Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Da-Lite Manuals
  4. Projection Screen
  5. Multi vision imager
  6. Instruction book

Da-Lite Multi vision imager Instruction Book

Hide thumbs Also See for Multi vision imager:
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual See also: Instruction Book
The Da-Lite Difference.
DA-LITE SCREEN COMPANY, INC.
Instruction Book for
3100 North Detroit Street
Post Office Box 137
multI vIsIon Imager
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com

Advertisement

loading

Related Manuals for Da-Lite Multi vision imager

Summary of Contents for Da-Lite Multi vision imager

  • Page 1 The Da-Lite Difference. DA-LITE SCREEN COMPANY, INC. Instruction Book for 3100 North Detroit Street Post Office Box 137 multI vIsIon Imager Warsaw, Indiana 46581-0137 Phone: 574-267-8101 800-622-3737 Fax: 574-267-7804 Toll Free Fax: 877-325-4832 www.da-lite.com e-mail: info@da-lite.com...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS When using your video equipment, basic safety precautions should always be followed, including the following: 1. Read and understand all instructions before using. 2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
  • Page 3 SIDE BOTTOm FIGURE 1 - FRONT VIEW MULTI VISION IMAGER FRAME ASSEMBLY 1. The main frame pieces are individually paper wrapped and taped. Remove all paper from the pieces. DO NOT USE A UTILITY KNIFE TO REMOVE PAPER. 2. Lay frame pieces out on the floor or table as shown in figure 2. The top frame assembly has the roller, motor and tensioned fabric attached to it.
  • Page 4 5. Assemble right side of frame to the top and bottom of frame. This is done exactly the same way as the left side. 6. Insert motor phone RJ-45 jack into receptacle located at the top of the junction box. Insert motor cable connector to the connector located on the side of junction box.
  • Page 5 MULTI VISION IMAGER INSTALLATION WALL MOUNT 1. The screen is shipped with two 46” wall brackets. Screens with less than 96” viewing area width (not standard sizes) are shipped with one wall bracket. Two small “L” brackets are included to hold frame securely to wall at bottom.

  • Page 6: Important Note

    MULTI VISION IMAGER INSTALLATION RJ-14 PIN-OUTS RJ-22 PIN-OUTS (TAB IS FACING UP) (TAB IS FACING UP) 120V WIRING DIAGRAM +12V BLUE BUS (RP DATA) WHITE BUS (RP DATA) YELLOW RQ DATA GREEN RQ DATA GREEN BLACK BLACK RQ CLOCK WHITE...

  • Page 7: Stop Button

    SCREEN ADJUSTMENT FOR 120V SCREENS 1. Locate the wall switch and remove the cover plate from the 3-button wall switch and remove the switch from the junction box. 2. Locate the two tactile buttons on the back of the switch. They are square silver with black round buttons. See Figure 8 (VPI) or Figure 10 (LVC) for diagram.

  • Page 8: Troubleshooting

    TROUBLESHOOTING SYMPTOM CAUSE SOLUTION 1. Screen will not operate. (a) Incorrect line voltage. (a) Verify 115-125V (or 220-240V). If insufficient voltage, rewire Motor does not hum. incoming electric line. (b) Blown fuse. (b) Replace fuse. (c) Tripped circuit breaker. (c) Reset circuit breaker. (d) No power to operating switch (d) Check above.