1. Manuals
  2. Brands
  3. Da-Lite Manuals
  4. Projection Screen
  5. ViewShare Tensioned Advantage Electrol...
  6. Instruction book

Da-Lite ViewShare Tensioned Advantage Electrol Retrofit Instruction Book

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTRUCTION BOOK FOR
ViewShare Tensioned
Advantage Electrol Retrofit

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ViewShare Tensioned Advantage Electrol Retrofit and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Da-Lite ViewShare Tensioned Advantage Electrol Retrofit

Summary of Contents for Da-Lite ViewShare Tensioned Advantage Electrol Retrofit

  • Page 1 INSTRUCTION BOOK FOR ViewShare Tensioned Advantage Electrol Retrofit...

  • Page 2: Important Safety Instructions

    Pre-Installation Important Safety Instructions When using your video equipment, basic safety precautions Prior to Retrofit installation, you will need to run a CAT5 or should always be followed, including the following: CAT5e network cable from the motor end of your screen to the area in which your computer will be located.
  • Page 3 Removal of Old Screen and Roller Assembly Run the screen to the up position. Access Door Screws 2. Remove the access door by removing the screws from each end (Figure 1). Be sure to support the door during this step to avoid injury.
  • Page 4 Pre-Installation of ViewShare Screen and Roller Assembly Remove existing motor and pin end roller assembly brackets from inside the case. NOTE: At this point the inside of case will be empty except for the junction box connections on the motor end. Circular Knockouts 2.
  • Page 5 Transfer of Existing Motor Once the old screen and roller assembly is out of the case, remove the Phillips head screw securing the screen tensioning cable to the roller on the motor end (Figure 9). 2. Remove motor from the old screen and roller assembly and set aside (Figure 10).
  • Page 6 Transfer of Existing Motor (continued) 5. Completely remove both shipping brackets from the board. 6. Remove the three Phillips head screws from motor end bracket and remove wooden block (Figure 12). 7. On the ViewShare screen and roller assembly, loosen (but do not remove) the nut on the motor end arm bracket (Figure 13).
  • Page 7 Transfer of Existing Motor (continued) 9. Carefully lift the roller above the mounting bracket and remove Motor Tensioning the Phillips head screw securing the tensioning cable to the roller Plug Cable Screw (Figure 14). 10. Remove the wood block and plug from the end of the roller (Figure 14).
  • Page 8 Installation of ViewShare Screen and Roller Assembly NOTE: The ViewShare screen and roller assembly, which includes brackets and arms, must be installed as a complete unit. Shipping Do not attempt to disassemble these components during L-Bracket installation. Remove two 1/4 – 20 nuts from pin end and motor end mounting brackets on the ViewShare screen and roller assembly shipping board (Figure 16).
  • Page 9 To prevent damage to the motor, the standard duty cycle is 1 minute on and 3 minutes off. NOTE: The up and down limits were pre-set by Da-Lite, but might have shifted during installation. If your screen and roller assembly needs adjustment, please see Appendix A for your motor type.
  • Page 10 Installation of ViewShare Screen and Roller Assembly (continued) 10. Remove the USB to CAT5 extender labeled “Remote” from the shipping carton. At the motor end of the case, attach the USB cable coming from the ViewShare screen and roller assembly. On the other end of the USB to CAT5 extender, attach the CAT5 cable that was run through the circular knockout.
  • Page 11 Camera and Speakerphone Installation Connections (see wiring diagram below) The following components are necessary and included for camera and speakerphone installation. Connect your CAT5 cable to the local CAT5 to USB extender, which should be located near your computer. Connect the local •...
  • Page 12 If the computer is NOTE: The Da-Lite bowtie around the camera will glow when the using Windows 7 or later version, the computer will automatically camera is selected. If the window says "No camera detected", go detect the camera, choose the proper drivers, and install the back to the Connections section and check each step.

  • Page 13: Troubleshooting

    Troubleshooting Visit www.da-lite.com/products/product_videos.php to find You can contact us by email at info@da-lite.com or by phone at installation and troubleshooting tutorials. You will also find a link 800.622.3737 or 574.267.8101 with any additional troubleshooting to Live Chat for interactive support.

  • Page 14: Appendix A: Screen Adjustment For Type 1 Motor (Hv Suffix In Part Number)

    Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da-Lite. Should it be necessary to adjust for more or less drop of screen, proceed in the following manner: Remove two screws to remove access door.
  • Page 15 Appendix A: Screen Adjustment for Type 2 Motor (LT suffix in Part Number) TYPE 2 MOTOR TYPE 2 WALL SWITCH No manual limit adjustments RJ-22 cable on end of motor 3-wire connection NOTE: If stop button is pressed, the wall switch will reverse Remove the cover plate from the 3-button wall switch and remove the switch from the junction box.
  • Page 16 Appendix A: Screen Adjustment for Type 3 Motor (LS suffix in Part Number) TYPE 3 MOTOR TYPE 3 WALL SWITCH No manual limit adjustments RJ-45 cable on end of motor 3-wire connection Locate the wall switch and remove the cover plate from the wall the screen.

  • Page 17: Appendix B: Arm Adjustment

    Appendix B: Arm Adjustment When screen is lowered approximately six inches below the case, the elbows of the arms should be horizontally aligned with each other (Figure 23) 2. If the arms are not horizontally aligned loosen (but do not remove) the adjustment nut found inside the case behind the screen and roller assembly (Figure 24).
  • Page 20 EQUIPMENT, OR FOR INCIDENTAL, DIRECT, OR CONSEQUENTIAL DAMAGES OF ANY NATURE. In the event that there is a defect in materials or workmanship of a Da-Lite product, you may contact our Sales Partners at PO Box 137, Warsaw, IN 46581-0137, (574) 267-8101, (800) 622-3737.

This manual is also suitable for:

Viewshare

Table of Contents