Troubleshooting - Panasonic TH-103PB1U Operating Instructions Manual

Troubleshooting

Before you call for service, determine the symptoms and make a few simple checks as shown below.
Symptoms
Picture
Interference
Normal Picture
No Picture
No Picture
No Color
No remote control operations can be performed.
A cracking sound is sometimes heard from the unit.
The top or bottom of the picture on the screen is cut
off when I use the zoom function.
Areas at the top and bottom of the screen where the
image is missing appear when I use the zoom function.
I can hear sounds coming from inside the unit.
Parts of the unit become hot.
Power automatically turns off unexpectedly.
Power indicator is blinking in red.
This Plasma Display uses special image processing. Hence a slight time lag may occur between image and audio, depending on the type of input
signal. However, this is not a malfunction.
Plasma Display panel
Symptoms
The screen darkens slightly when bright pictures with
minimal movements are shown.
It takes a while for the picture to appear.
The edges of the images À icker.
The brightness on both sides of images in 4:3 mode
changes.
Some parts of the screen do not light up.
Image retention appears
Whirring sounds can be heard from the display unit.
60
Sound
Electrical Appliances
Noisy Sound Cars / Motorcycles
Fluorescent light
Volume
No Sound (Check whether the mute function has been activated on the remote control.)
Check if speakers are connected properly.
Not plugged into AC outlet
Not switched on
No Sound
PICTURE and BRIGHTNESS/Volume setting
(Check by pressing the power switch or stand-by button on the remote control.)
If a signal with a non-applicable color system format, or frequency is input, only the input
Normal Sound
terminal indication is displayed.
Color controls set at minimum level. (see page 27, 28)
Normal Sound
COLOR SYSTEM (see page 50)
Check whether the batteries have discharged completely and, if they have not, whether they
were inserted properly.
Check whether the remote control sensor is exposed to an outdoor light or a strong À uorescent light.
Check whether the remote control designed speci¿ cally for use with the unit is being used.
(The unit cannot be operated by any other remote control.)
If there is nothing wrong with the picture or sound, this is the sound of the cabinet undergoing
very slight contractions in response to changes in the room temperature. There are no adverse
effects on the performance or other aspects.
Adjust the position of the picture on the screen.
When using a video software program (such as a cinema size program) with a screen wider than one in
the 16:9 mode, blank areas separate from the images are formed at the top and bottom of the screen.
When the power is turned on, a sound of the display panel being driven may be heard: This is
normal and not indicative of malfunctioning.
Even when the temperature of parts of the front, top and rear panels has risen, these temperature
rises will not pose any problems in terms of performance or quality.
Check the settings of "PC POWER MANAGEMENT", "DVI-D POWER MANAGEMENT", "NO
SIGNAL POWER OFF" and "NO ACTIVITY POWER OFF" in the SETUP menu. Any of them
may be set to "ON (ENABLE)". (see page 41, 44)
There is possibility of malfunction. Please contact an Authorized Service Center.
The screen will darken slightly when photos, still images of a computer or other pictures with minimal
movements are shown for an extended period. This is done to reduce image retention on the screen
and the shortening of the screen's service life: It is normal and not indicative of malfunctioning.
The unit digitally processes the various signals in order to reproduce esthetically pleasing
images. As such, it sometimes takes a few moments for the picture to appear when the power
has been turned on, when the input has been switched.
Due to the characteristics of the system used to drive the panel, the edges may appear to À icker
in the fast-moving parts of the images: This is normal and not indicative of malfunctioning.
When viewing the side panels at the "BRIGHT" or "MID" setting, the brightness on both sides
may change depending on the kind of program shown: This is normal and not indicative of
malfunctioning.
The plasma display panel is manufactured using an extremely high level of precision technology,
however, sometimes some parts of the screen may be missing picture elements or have luminous
spots. This is not a malfunction.
Do not allow a still picture to be displayed for an extended period, as this can cause a permanent
image retention to remain on the Plasma Display.
Examples of still pictures include logos, video games, computer images, teletext and images
displayed in 4:3 mode.
Note:
The permanent image retention on the Plasma Display resulting from ¿ xed image use is not
an operating defect and as such is not covered by the Warranty.
This product is not designed to display ¿ xed images for extended periods of time.
The display unit is ¿ tted with a cooling fan to dissipate heat generated during normal use. The
whirring sound is caused by rotation of the fan and is not a malfunction.
Checks
Check