Checking Drive Belts; Checking And Replacing Fuses; Replacing Accessory Fuse; Replacing A Fusible Link - Hyundai Elantra Owner's Manual

G190A01A-AAT

CHECKING DRIVE BELTS

CHECKING DRIVE BELTS CHECKING DRIVE BELTS CHECKING DRIVE BELTS CHECKING DRIVE BELTS
Water Pump Pulley
0.2 ~ 0.24 in.
(5.1 ~ 6 mm)
Generator Pulley
Crankshaft Pulley
Drive belts should be checked periodically for
proper tension and adjusted if necessary. At the
same time, belts should be examined for cracks,
wear, fraying or other evidence of deterioration
and replaced if necessary.
Belt routing should also be checked to be sure
there is no interference between the belts and
other parts of the engine. After a belt is re-
placed, the new belt should be adjusted again
after two or three weeks to eliminate slack
resulting from initial stretching after use.
DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE
DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE DO-IT-YOURSELF MAINTENANCE
G200A01A-AAT
CHECKING AND REPLACING CHECKING AND REPLACING CHECKING AND REPLACING CHECKING AND REPLACING CHECKING AND REPLACING
FUSES FUSES FUSES
FUSES FUSES

Replacing a Fusible Link

Replacing a Fusible Link Replacing a Fusible Link Replacing a Fusible Link Replacing a Fusible Link
SSA6190A
A fusible link will melt if the electrical circuits
from the battery are ever overloaded, thus pre-
venting damage to the entire wiring harness.
(This could be caused by a short in the system
drawing too much current.) If this ever happens,
have a Hyundai dealer determine the cause,
repair the system and replace the fusible link.
The fusible links are located in a relay box for
easy inspection.
CAUTION: CAUTION:
CAUTION: CAUTION: CAUTION:
When replacing a fusible link, never use When replacing a fusible link, never use When replacing a fusible link, never use When replacing a fusible link, never use When replacing a fusible link, never use
anything but a new fusible link with the anything but a new fusible link with the
anything but a new fusible link with the anything but a new fusible link with the anything but a new fusible link with the
same or lower amperage rating. Never use a same or lower amperage rating. Never use a same or lower amperage rating. Never use a
same or lower amperage rating. Never use a same or lower amperage rating. Never use a
piece of wire or a higher-rated fusible link. piece of wire or a higher-rated fusible link. piece of wire or a higher-rated fusible link. piece of wire or a higher-rated fusible link. piece of wire or a higher-rated fusible link.
This could result in serious damage and This could result in serious damage and This could result in serious damage and This could result in serious damage and This could result in serious damage and
create a fire hazard. create a fire hazard. create a fire hazard. create a fire hazard. create a fire hazard.
G200B01E-AAT

Replacing Accessory Fuse

Replacing Accessory Fuse Replacing Accessory Fuse Replacing Accessory Fuse Replacing Accessory Fuse
Bad Good
The fuse box for the lights and other electrical
AS60310A
accessories will be found in the backside of multi
box located in the left side of driver. Inside the box
you will find a list showing the circuits protected
by each fuse.
If any of your car's lights or other electrical
accessories stop working, a blown fuse could
be the reason. If the fuse has burned out, you
will see that the metal strip inside the fuse has
burned through. If you suspect a blown fuse,
follow this procedure:
1. Turn off the ignition and all other switches.
2. Open the fuse box and examine each fuse.
3. Be sure to check all other fuses even if you
Remove each fuse by pulling it toward you
(a small "fuse puller" tool is contained in the
fuse box to simplify this operation).
find one that appears to have burned out.
B200B01E
6-15