Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bosch Conettix ITS-D6682-INTL
Summary of Contents for Bosch Conettix ITS-D6682-INTL
- Page 1 Conettix ITS-D6682-INTL Installation Guide Ethernet Network Adapter...
-
Page 2: Table Of Contents
Conettix ITS-D6682-INTL | Installation Guide | Contents Contents Introduction............3 Network Interface..........3 Serial Interface..........3 LEDs ..............3 Installation............4 Mounting the D6682.......... 4 Connecting the D6682 ........4 Configuring and Programming the D6682 ..5 Factory Default IP Address ....... 5 Identifying the MAC Hardware Address .... -
Page 3: Introduction
Conettix ITS-D6682-INTL | Installation Guide | 1.0 Introduction Serial Interface Trademarks Figure 2: D6682 Network Interface ® ® Microsoft Windows 2000, XP, Vista™, and ®, MS-DOS are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. -
Page 4: Installation
Conettix ITS-D6682-INTL | Installation Guide | 2.0 Installation 2.0 Installation Figure 3: D6682 Connections Mounting the D6682 Mount the D6682 on a rail or other user-supplied spot behind the D6600 that it will be connected to. Refer to Figure 3. -
Page 5: Configuring And Programming The D6682
Conettix ITS-D6682-INTL | Installation Guide | 3.0 Configuring and Programming the D6682 Using ARP to Assign the IP 3.0 Configuring and Address Programming the D6682 Bosch Security Systems, Inc. recommends that you read this entire section before proceeding. Also, Factory Default IP Address ensure that power is applied to the D6682 and the Ethernet Network RJ45 connection is in place. -
Page 6: Arp Command Usage
Conettix ITS-D6682-INTL | Installation Guide | 3.0 Configuring and Programming the D6682 3. Type the arp –s command with the IP ARP Command Usage address and the MAC hardware address. Perform the following procedure when using the ARP For this example the IP address is command to assign an IP address to a D6682. -
Page 7: Using Telnet To Finish The Configuration
Conettix ITS-D6682-INTL | Installation Guide | 3.0 Configuring and Programming the D6682 Using Telnet to Finish the Configuration Although the screen shots are specific to Windows 2000, they are similar for Windows XP and Vista. In Windows Vista, Telnet is disabled by default. - Page 8 Conettix ITS-D6682-INTL | Installation Guide | 3.0 Configuring and Programming the D6682 12. If you pressed [ENTER] within five sec, you 15. When asked to set the Gateway IP address should see the following screen. (Figure 10), type N and press [ENTER] to Refer to Figure 9.
- Page 9 Conettix ITS-D6682-INTL | Installation Guide | 3.0 Configuring and Programming the D6682 19. Press [1] [ENTER] to configure Channel 1. Table 2: Netmask Address Baudrate 9600 appears. The D6682 must be set to a baud rate Number of Host Bits Netmask of 38400.
-
Page 10: Programming Overview For The D6600
Conettix ITS-D6682-INTL | Installation Guide | 3.0 Configuring and Programming the D6682 27. If you want to enable encryption, select 6 After you make all the changes and Security from the main menu and continue verify them for accuracy, you must save with Step 28. -
Page 11: Specifications
Conettix ITS-D6682-INTL | Installation Guide | 4.0 Specifications 4.0 Specifications Table 3: Specifications Supported ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, and HTTP Protocols Connectors Serial: 2 - DB9M DTE serial ports Network: 1 - RJ45 10Base-T/100Base-TX Ethernet port... - Page 12 Bosch Security Systems, Inc. 130 Perinton Parkway Fairport, NY 14450-9199 (800) 289-0096 © 2009 Bosch Security Systems, Inc. F01U126778-01...