User Config Menu - Sony LMD-2451TD Operating Instructions Manual

Submenu Setting
PICTURE CONTROL Adjusts to monitor the picture more
clearly.
• SIZE H: Adjusts the horizontal
• SIZE V: Adjusts the vertical size
• SHIFT H: Adjusts the position of
• SHIFT V: Adjusts the position of
• DOT PHASE: Adjusts the dot
• PITCH: Adjusts the horizontal
• RESOLUTION: Sets when the
• RESET: Resets the value of
size of the picture. The
higher the setting, the larger
the horizontal size of the
picture. The lower the
setting, the smaller the
horizontal size of the
picture.
of the picture. The higher
the setting, the larger the
vertical size of the picture.
The lower the setting, the
smaller the vertical size of
the picture.
the picture. As the setting
increases, the picture moves
to the right, and as the
setting decreases, the picture
moves to the left.
the picture. As the setting
increases, the picture moves
up, and as the setting
decreases, the picture moves
down.
phase. Adjust the picture
further for a finer picture
after APA (page 31) is
adjusted.
size of the picture with the
left side of the picture fixed.
The higher the setting, the
larger the width of the
picture. The lower the
setting, the narrower the
width of the picture.
computer signal is input and
it is difficult to understand
the signal type such as
XGA/60, WXGA/60,
UXGA/60 or WUXGA/60.
•XGA: Displayed as XGA
signal.
•WXGA: Displayed as
WXGA signal.
•UXGA: Displayed as
UXGA signal.
•WUXGA: Displayed as
WUXGA signal.
SIZE H, SIZE V, SHIFT H,
SHIFT V, DOT PHASE and
PITCH to the factory preset
value.

USER CONFIG menu

The USER CONFIG menu is used for setting the
system, marker, multi display, function button, closed
caption, audio, option and 3D.
USER CONFIG
S Y S T E M S E T T I N G :
M A R K E R S E T T I N G :
M U LT I D I S P L AY S E T T I N G :
F U N C T I O N B U T T O N S E T T I N G :
C L O S E D C A P T I O N S E T T I N G :
AU D I O S E T T I N G :
O P T I O N S E T T I N G :
3 D S E T T I N G :
SYSTEM SETTING
USER CONFIG – SYSTEM SETTING
M AT R I X :
C O M P O N E N T L E V E L :
N T S C S E T U P :
S C A N :
F O R M AT D I S P L AY:
L A N G U A G E :
P O W E R S AV I N G :
I / P M O D E :
B A C K G R O U N D :
Submenu Setting
MATRIX Applied to 480/60I or 480/60P
signal. Select 601 or 709.
COMPONENT LEVEL Selects the component level from
among three modes.
• SMPTE: for 100/0/100/0 signal
• BETA0: for 100/0/75/0 signal
• BETA7.5: for 100/7.5/75/7.5
NTSC SETUP Selects the NTSC setup level from
two modes.
The 7.5 setup level is used mainly
in North America. The 0 setup level
is used mainly in Japan.
SCAN Enables setting of the scan mode by
the button which the scan function
is assigned. Select from among
STANDARD and FULL+NATIVE.
The displayed picture differs
according to the selected mode (see
"Scan mode image" on page 28).
When STANDARD is selected
NORMAL scan (0% scan) and
OVER scan (5% over scan)
When FULL+NATIVE is selected
NORMAL scan, OVER scan,
FULL screen (LMD-2451TD) and
NATIVE
NATIVE is effective only when the
following signals are input:
1080i, 1080P, 720P.
1080P can be selected when BKM-
250TG is installed.
xxx
xxxx
x
xxxxx
xxxx
E N G L I S H
xxx
xxxxxxx
xxx
signal
Adjustment Using the Menus
27