Sony LMD-2451TD Operating Instructions Manual page 31

About the function assigned to the
function button
SCAN
Press the button to change the scan size of the picture
according to the setting of STANDARD or
FULL+NATIVE selected in SCAN (page 27).
ASPECT
Press the button to set the aspect ratio of the picture, 4:3
or 16:9.
Note
The panel of LMD-2451TD has 16:10 aspect ratio.
When the 16:9 signal is displayed, black bars appear in
the upper and lower positions of the display. This is not
a malfunction. (See "Scan mode image" on page 28.)
EXT SYNC (external sync)
Press the button to operate the unit on an external sync
signal through the EXT SYNC IN connector.
EXT SYNC works when the component/RGB signals
are input.
I/P MODE
Press the button to set the delay by the picture
processing to the minimum level when interlace signal
is input. The mode switches in the sequence INTER-
FIELD t FIELD MERGE t LINE DOUBLER with
every press of the button (see page 28).
MULTI DISPLAY
Press the button to display the multi display. Set the
multi display setting in the MULTI DISPLAY
SETTING menu (see page 29).
CLOSED CAPTION
Press the button to display the closed caption. Set the
closed caption setting in the CLOSED CAPTION
SETTING menu (see page 32).
Not available for the signal input from BKM-227W.
MONO
Press the button to display a monochrome picture. When
the buttons is pressed again, the monitor switches
automatically to color mode.
H/V DELAY
Press the button to observe the horizontal and vertical
sync signals at the same time.
MARKER
Press the button to display the marker. Set the aspect
marker and safety area size in the MARKER SETTING
menu (see page 29).
APA (Auto Pixel Alignment)
Press the button to adjust the picture automatically to
maximum clarity for the signal input to the HD15 input
connector. For finer according to the input signal, see
DOT PHASE on page 27.
When the menu screen is displayed, the APA does not
function.
Note
If the APA operation does not finish correctly depending
on the input signal, adjust DOT PHASE (page 27).
BLUE ONLY
Press the button to eliminate the red and green signals.
Only blue signal is displayed as an apparent
monochrome picture on the screen. This facilitates
chroma and phase adjustments and observation of signal
noise.
2D/3D SELECT
Press the button to switch from 2D display mode to 3D
display mode. For detailed 3D display settings, select
2D/3D SELECT under the 3D SETTING menu.
Pressing the button again switches to 3D display mode.
Install BKM-250TG with a serial number 7100001 or
later to display HD-SDI signal in 3D.
CHECKER BOARD
When displaying 2D images, press the button to display
input signals from the IN (INPUT)-1 and IN (INPUT)-2
connectors in grid pattern. Two input signals can be
monitored on the screen at a time. Pressing the button
again displays the input signals in default pattern. Install
BKM-250TG with a serial number 7100001 or later to
display HD-SDI signal in 3D.
Note
This function is only available in 2D display mode.
L/R SWITCH
Press the button to quickly switch between a dual-stream
HD-SDI signal from IN (INPUT)-1 connector on BKM-
250TG and one from IN (INPUT)-2 connector. You can
easily compare the two input signals. Install BKM-
250TG with a serial number 7100001 or later to display
HD-SDI signal in 3D.
Note
This function is only available in 2D display mode.
HOROPTER CHECK
Press the button to select display formats in monitoring
left/right signals for 3D image display. Select the desired
format from HOROPTER CHECK (page 34) under the
3D SETTING menu. Pressing the button again switches
to default display format. Install BKM-250TG with a
31
Adjustment Using the Menus