IBM Nortel Networks L2/3 Manual page 146

* 10.20.0.0
* 10.20.0.243
* 10.20.0.255
* 10.35.0.0
* 10.35.0.243
* 10.35.0.255
* 10.36.0.0
* 10.36.0.243
* 10.36.0.255
* 10.45.0.0
* 10.46.0.0
* 10.99.0.0
* 127.0.0.0
* 255.255.255.255 255.255.255.255 255.255.255.255 broadcast broadcast
>> GbESM_1 - IP Routing# /i/l3/rip
------------------------------------------------------------
[RIP Information Menu]
routes
dump
>> GbESM_1 - RIP Information# routes
10.10.0.0/24 via 10.20.0.244 metric 2
10.20.0.0/24 via 10.10.0.244 metric 2
10.35.0.0/24 via 10.20.0.244 metric 3
10.36.0.0/24 via 10.20.0.244 metric 3
10.45.0.0/24 via 10.10.0.244 metric 2
10.46.0.0/24 via 10.10.0.244 metric 2
10.99.0.0/24 via 10.36.0.246 metric 2
>> GbESM_1 - RIP Information# dump
Enter interface number: (1-128) or 0 to show all 10
RIP USER CONFIGURATION :
RIP on updat 30
RIP Interface 10 : 10.10.0.243,
version 2, listen enabled, supply enabled, default listen
poison disabled, trigg enabled, mcast enabled, metric 1
auth none,key none
Cisco commands to verify RIP
The sh ip route command is the CIsco equivalent of the dump command shown above. RIP
routes are marked by the letter R in the left hand column. Most OSPF commands are marked
by the letter O. The show ip protocol command (shown in Example 7-37) provides detailed
information about the operation of RIP when it is running (and also on OSPF when it is
running).
Example 7-37 Cisco commands to verify RIP
sh ip prot
*** IP Routing is NSF aware ***
Routing Protocol is "rip"
Sending updates every 30 seconds, next due in 19 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 2, receive version 2
Nortel Networks L2/3 Ethernet Switch Module for IBM Eserver BladeCenter
132
255.255.255.0 10.20.0.243
255.255.255.255 10.20.0.243
255.255.255.255 10.20.0.255
255.255.255.0 10.35.0.243
255.255.255.255 10.35.0.243
255.255.255.255 10.35.0.255
255.255.255.0 10.36.0.243
255.255.255.255 10.36.0.243
255.255.255.255 10.36.0.255
255.255.255.0 10.10.0.244
255.255.255.0 10.10.0.244
255.255.255.0 10.36.0.246
255.0.0.0 0.0.0.0
- Show RIP routes
- Show RIP user's configuration
direct fixed
local addr
broadcast broadcast
direct fixed
local addr
broadcast broadcast
direct fixed
local addr
broadcast broadcast
indirect rip
indirect rip
indirect rip
martian martian
enabled
20
20
20
35
35
35
36
36
36
2 10
2 10
2 36