Enhanced Remote Panic - Omega Crime Guard 850i4 Operation Manual

If a customized SecureCode has been programmed, the system will disarm a few
seconds after the correct entry, and if an incorrect entry is made, the system will
not disarm. A procedure which separate, but similar, to an Emergency Override
is the Alarm Valet Mode (page 21), which prevents the system from performing
any automatic arming operations which may be otherwise programmed to occur.
SecureCode:
Should a more secure access to Emergency Override be desired, the
"SecureCode" programmable feature may be used. Instead of "1 press" of the
Valet Switch to perform an Emergency Override, a customized programming of
the SecureCode would require from 2 to 12 presses. An owner-customized
SecureCode will only affect the Emergency Override operation, and the Anti-
Carjacking operations (if they are used). Placing the system into Alarm Valet
Mode, Starting Valet Mode, or Full Valet Mode is not affected; these operations
will still involve only a single Valet Switch press.
A customized SecureCode will add a slight delay to the Emergency Override-
if the pressing of the Valet Switch is the "as received" default setting of "1 press",
the system will disarm the moment the Valet Switch is released from the single
press. If a customized SecureCode has been programmed, the system will disarm
a few seconds after the correct entry. If an incorrect entry is made, the system will
not disarm.
SecureCode programming is described on page 29.

ENHANCED REMOTE PANIC

To Activate "Enhanced Remote Panic":
Press & Hold for 3 Seconds the "Arm/Lock" Button (
OR the "Disarm/Unlock" Button (
OR
Hold 3
Hold 3
seconds
seconds
* An optional doorlock interface must be installed
U
)
J
)
THE SIREN SOUNDS
THE PARKING LIGHTS
WILL FLASH
THE DOORS WILL LOCK
LOCK OR UNLOCK*
OR
Page 14
the Vehicle Recovery operation from the transmitter or transceiver in the event
that you are forced from your car. "Remote Activated" Vehicle Recovery is one
three methods of activating this feature, which is explained on page 25.
Programming Transmitter Activated Anti Car-Jacking:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released sixteen times. The system's response will be sixteen siren chirps, and
the Status Light flashing sixteen times, pausing, then repeating. Within 10
seconds, press and release the transmitter/transceiver's "Arm/Lock" button to
turn on the Transmitter Activated Vehicle Recovery feature (the siren chirps
once) or the "Disarm/Unlock" button to turn the feature off (the siren chirps twice).
Feature #17
This feature allows the permanent removal of the system's chirping the siren
as an audible confirmation when performing functions such as Arming and
Disarming. Please note that utilizing this feature to remove the confirmation
chirps does not affect siren chirping operations associated with the Unauthorized
Transmitter Alert warning, sensor prewarning or Programming Mode.
Note: Using this feature to turn off the siren chirps also turns the chirps in the
Echo transceiver- the Echo emulates the system's siren chirps.
Programming the Chirp Confirmation:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released seventeen times. The system's response will be seventeen siren chirps,
and the Status Light flashing seventeen times, pausing, then repeating. Within
10 seconds, press and release the transmitter/transceiver's "Arm/Lock" button to
turn the Chirp Confirmation on (the siren will chirp once) or the "Disarm/
Unlock" button to turn the Chirp Confirmation off (the siren will chirp twice).
Feature #18
This Feature sets the period of time that the engine will run after being
remotely started. If the engine is not stopped by a transmitter or transceiver, or
a safety circuit violation, the engine will automatically stop upon the expiration
of the selected time period.
Hold 3 Programming 10 or 20 Minute Run Time:
seconds
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released eighteen times. The system's response will be eighteen siren chirps, and
the Status Light flashing eighteen times, pausing, then repeating. Within 10
Hold 3
seconds, press and release the transmitter/transceiver's "Arm/Lock" button to
seconds
Chirp Confirmation
(Factory Default Setting On)
Remote Start Run Time 10 Or 20 Minutes
(Factory Default Setting 10 Minutes)
Page 35