Remote Sensor Bypass; Remote Engine Starting - Omega Crime Guard 850i4 Operation Manual

REMOTE SENSOR BYPASS

To Activate Remote Sensor Bypass:
Press & Release the "Arm/Lock" Button (
Release the "Auxiliary Output #2" Button ( II )
THE SIREN WILL CHIRP TWICE TO
THE SIREN THEN CHIRPS ONCE
AGAIN TO CONFIRM SENSOR
1st
2nd
2nd
" turning off" the sensor any- time the system is
armed using the transmitter or transceiver. When
1st
the sensor is bypassed, only the sensor zone is by-
passed and all other protected zones will remain fully
operational and vigilant. The sensor zone will reset to
its normal operation the next time the system is armed.
* An optional doorlock interface must be installed

REMOTE ENGINE STARTING

This unit is designed to be installed on
automatic transmission vehicles only!
The remote engine starting feature should not be used when
the vehicle is parked in an enclosed structure or garage!
4
Your Crime Guard 850i system offers the ultimate in comfort and convenience-
remote engine starting. This feature allows the vehicle's interior to be warmed
in the winter or cooled in the summer before you enter the vehicle. Simply leave
the climate controls set to the desired settings when leaving the vehicle prior to
using the remote starting feature. The following pages explain the remote engine
starting operations.
U
) to Arm, then Press &
CONFIRM ARMING
THE PARKING LIGHTS
BYPASS
WILL FLASH TWICE
TO CONFIRM
THE DOORS WILL LOCK
UPON ARMING*
Remote Sensor Bypass allows the option of
Page 18
Feature #5
This feature prevents your system from being disarmed accidentally, config-
uring the system to automatically rearm itself 90 seconds after it has been
Disarmed by the transmitter. The operation of the Automatic Rearming feature
is explained in more detail on pages 12-13.
Programming Automatic Rearming:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released five times. The system's response will be five siren chirps, and the Status
Light flashing five times, pausing, then repeating. Within 10 seconds, press and
ARMING
release the transmitter/transceiver's "Arm/Lock" button to turn on the Automatic
Rearming feature (the siren will chirp once) or the "Disarm/Unlock" button to
turn the Automatic Rearming feature off (the siren will chirp twice).
Feature #6
This feature configures the Auxiliary Output #2 to automatically Disarm the
system at the same when it is used.
Programming Auxiliary Channel #2 Disarms System:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released six times. The system's response will be six siren chirps, and the Status
Light flashing six times, pausing, then repeating. Within 10 seconds, press and
release the transmitter/transceiver's "Arm/Lock" button to have the system
Disarm when Auxiliary Output #2 is used (the siren will chirp once) or the
"Disarm/Unlock" button to have Auxiliary Output #2 not Disarm the system
when it is used (the siren will chirp twice).
Feature #7
This feature configures the system to illuminate the vehicle's parking and
interior lights for 30 seconds when it is Disarmed. Otherwise, if this feature is
turned off, the parking lights will illuminate only 5 seconds upon Disarming.
Programming Parking Light Illumination Upon Disarm:
Follow Steps 1 to 4 on page 27; at Step 4 the Valet Switch will be pressed and
released seven times. The system's response will be seven siren chirps, and the
Status Light flashing seven times, pausing, then repeating. Within 10 seconds,
press and release the transmitter/transceiver's "Arm/Lock" button to have the
parking lights turn on for 30 seconds when the system is Disarmed (the siren will
chirp once) or the "Disarm/Unlock" button to have the parking lights on for 5
seconds when the system is Disarmed (the siren will chirp twice).
Automatic Rearming
(Factory Default Setting Off)
Auxiliary Output #2 Also Disarms System
(Factory Default Setting On)
Parking Light Illumination Upon Disarm
(Factory Default Setting On)
Page 31