Programming The 850I 4 - Omega Crime Guard 850i4 Operation Manual

To Enter Alarm Valet Mode:
With the system disarmed, and without pressing the brake pedal, Press & Hold
the Valet Switch for 2 seconds.
• The siren will chirp twice, the parking lights will flash twice and the Status
Indicator Light will illuminate solid Red, then a series of Green flashes, then
return to solid Red. The Green flashes, numbering from 1 to 6 times, is a
remote starting diagnostic code (see page 24).
• To indicate that the system is in Alarm Valet Mode, the Status Indicator Light
remains solid Red whenever the system is in Alarm Valet Mode.
• To remind the user that the system is in Alarm Valet Mode, the siren will
chirp once every time the vehicle's ignition is turned off.
To Enter Starting Valet Mode:
With the system disarmed, and depressing the brake pedal, Press & Hold the
Valet Switch for 2 seconds.
• The siren will chirp twice, the parking lights will flash twice and the Status
Indicator Light will illuminate solid Green to confirm that the system is in
Starting Valet Mode.
• There is no audible reminder that the system is in Starting Valet mode.
To Enter both Modes (Full Valet Mode):
With the system disarmed, Press & Hold the Valet Switch for 4-6 seconds with
the brake pedal in both conditions. For example, start pressing the Valet Switch
with the brake pedal unpressed; as soon as two chirps are heard, press the brake
pedal but do not release the Valet Switch. As soon as a second set of chirps is
heard, the Valet Switch may be released. The system is now in Full Valet Mode.
It does not matter in what order the pressed or unpressed brake pedal occurs.
• Once the system is in Full Valet Mode the Status Indicator Light will slowly
alternate Green and Red to confirm that the system is in Full Valet Mode. This
indication is present whenever the system is in Full Valet Mode.
• There will be the single chirp reminder every time the ignition turns off. This
is for the Valet Mode part of the Full Valet Mode condition.
To Exit any of the 3 forms of Valet Mode:
Simply Press & Release the Valet Switch at any time.
• The Status Indicator Light will turn off to confirm exit from either Alarm
Valet Mode, Starting Valet Mode, or both.
The Echo Transceiver's Reaction to Valet Mode:
If the Echo transceiver was last used to operate the system, when the system
is placed into alarm Valet Mode it will send a signal to the Echo. When this occurs:
Page 22
PROGRAMMING THE 850i
The Crime Guard 850i 4 is a sophisticated, yet flexible security and convenience
system. Many of its operations may be configured as the user desires.
"Programming Mode" allows you to configure 29 operational features to suit
your wants and needs. Your vehicle's ignition key and the Valet Switch are used
to enter the Programming Mode, as described by the three steps listed below.
Once in Programming Mode, the Valet Switch is used to access the desired
feature, and the transmitter or transceiver is then used to change the chosen
feature's status. During the process, the siren and the Status Indicator Light
indicate certain conditions of Programming Mode and the chosen feature's
status.
Once the system is in Programming Mode, the Valet Switch is then pressed
and released the number of times equal to the feature number which is to be
accessed for programming. After pressing the Valet Switch as many times as the
feature number, the siren will chirp the same number of times and the Status
Indicator Light will flash the same number, between pauses.
Once the feature has been selected its status, or setting, can be chosen by
pressing the appropriate button on the transmitter. Basically, pressing the
transmitter's "Arm/Lock" button turns the feature on, or pressing the transmitter's
"Disarm/Unlock" button turns the feature off. Features which are not "on or off"
features, such as the activated alarm duration of 30 or 60 seconds, are noted
otherwise.
To Enter Programing Mode:
Step 1 Turn the vehicles's ignition on.
Step 2 Turn the ignition off.
Step 3 Within 5 seconds, Press & Release the Valet Switch 5 times.
•The siren will chirp and sound briefly and the Status Light will
flash to confirm that the system is entering Programing Mode.
•Once in Programming Mode, if 10 seconds of no programming
activity occurs, the system will exit Programming Mode. Program-
ming activity is the pressing of the Valet Switch or pressing a trans-
mitter button once a feature is accessed.
To Access a Feature:
Step 4 Within 10 seconds, Press & Release the Valet Switch the same num-
ber of times as the desired feature's number.
•The siren will chirp and the Status Indicator Light will flash as
many times as the Valet Switch was pressed to indicate the feature
number which is now accessed.
4
Page 27