Download  Print this page

Kenmore 2220693 Use & Care Manual page 7

Hide thumbs

Advertisement

NOTE: It may only be necessary to remove either the door handle
or the doors to get your product through the doorway of your
residence. Measure the door opening to determine whether to
remove the refrigerator handles or the doors.
Handle Removal
(optional)
1. Apply firm pressure with your hand on the face of trim. Slide
top trim up and bottom trim down away from handle. Lift trim
pieces off shoulder screws (see Graphic 1).
2. Remove handle screws and handles.
3. Move refrigerator into place. Replace handles as shown (see
Graphic 1).
Door Removal
Door and Hinge Replacement
1. Replace both bottom hinges, if removed. Tighten screws.
2. Assistance may be needed to feed the water line through the
bottom hinge while reinstalling the freezer door. Carefully feed
the dispenser tubing through the bottom left hinge before
replacing the door on the hinge.
NOTE: Provide additional support for the doors while the top
hinges are being replaced. Do not depend on the door magnets
to hold the doors in place while you are working.
3.
Reconnect water dispenser tubing by pushing tubing into
fitting until it stops and black mark touches face of fitting (see
Graphic 3). On some models, replace tubing in hose clip.
4. Align and replace the top left hinge as shown (see Graphic 4).
Tighten screws.
Electrical Shock Hazard
Disconnect power before removing doors.
Failure to do so can result in death or
electrical shock.
1. Unplug refrigerator or disconnect
power.
2. Open both refrigerator doors. Remove the base grille by
pulling up on the bottom outside corners (see Graphic 2).
3. Close both doors and keep them closed until you are ready to
lift them free from the cabinet.
4. If you have a dispenser (ice or water), disconnect
the water
dispenser tubing located behind the base grille on the freezer
door side (see Graphic 3).
Press red outer ring against the face of fitting and pull the
dispenser tubing free.
On some models, remove tubing from hose clip.
5. Remove top left hinge screw and cover as shown (see
Graphic 4).
6. Disconnect
wiring plug and both ground wires from ground
wire screw (on some models) as shown (see Graphic 4).
7. Remove remaining left hinge screws and hinge as shown (see
Graphic 4). Do not remove screw 1.
8. Carefully lift freezer door straight up off bottom hinge (see
Graphic 5). The water dispenser tubing remains attached to
the freezer door and pulls through the bottom le_ hinge.
Make sure you protect the dispenser tubing from damage.
9. Remove top right hinge cover and screws as shown (see
Graphic 6). Do not remove screw 1.
10. Lift the refrigerator door straight up off bottom hinge.
11. It may not be necessary to remove the bottom hinge to move
the refrigerator through a doorway. Both bottom hinges have
similar construction.
Disassemble the hinges as shown (see Graphic 7). Do not
remove screw 1.
Electrical Shock Hazard
Reconnect both ground wires.
Failure to do so can result in death or
electrical shock.
Style 1
Reconnect both ground wires.
Reconnect wiring plug.
Style 1
Style 2
Reconnect wiring plug.
5.
Replace left hinge cover and screws.
6.
Replace the refrigerator door by carefully lifting the door onto
the bottom right hinge.
7. Align and replace the top right hinge as shown (see
Graphic 6). Tighten screws.
8.
Replace hinge cover and screws. Tighten screws.
9.
Plug into a grounded 3 prong outlet.

Advertisement

Table of Contents
loading

  Related Manuals for Kenmore 2220693

This manual is also suitable for:

Elite 106 series