Error Messages And Warning Messages; About Error Messages; About Warning Messages - Sony SRMASTER SR-R4 Operation Manual

Error Messages and
Warning Messages

About Error Messages

When the system stops operating incorrectly
because of an internal error, a warning tone
sounds and a popup window appears in the
display of the control panel with an error
message.
Tip
Only one message is displayed at one time, even if
multiple errors occur. The number of current errors
appears at the bottom of the popup window. Be sure to
check the messages for all errors.
Example:
Popup window displaying error message "0010:
FAN1 STOP" (fan stopped)
dB
SDI SDI SDI SDI SDI SDI
0
-10
-20
-30
-60
EMP EMP EMP EMP EMP EMP
EE
L R L R L R L R L R L R
1 2 3 4 5 6
0010 0010
FAN STOP FAN STOP
PLAY LOCK
TCR LTC INTRP
00 00
H
1 Error(s)/
16.5V REMAIN
10min
Indicates that there is one
current error message.
Indicates that there are two current
warnings (see page 52).
To view the other messages, rotate the
SELECT/ENTER dial on the control panel.
When an error message appears
Eliminate the cause of the error, and power the
system off and on again.
If the same error message appears again when the
system is powered on, contact a Sony service
representative.
52

Error Messages and Warning Messages

SDI SDI SDI SDI SDI SDI SDI SDI SDI SDI
E RR OR
EMP EMP EMP EMP EMP EMP EMP EMP EMP EMP
L R L R L R L R L R L R L R L R L R L R
7 8 9 10 11 12 13 14 15 16
VTR OOOOO
DF EXT-LK KEYINHI
FAN 1 Stopped
RECINHI
00 00
M S F
2 Warning(s)
IN: --:--:--:--
LOCAL
ENCODE F65RAW
EE
STANDARD 23.98P
21:46
To close the error message popup window
Press the HOME button or the BACK button.
The error code is shown in the operation status
and warnings section of the HOME screen (see
page 13) until the cause of the error is removed.

About Warning Messages

If an error is detected, a warning message code
appears in the operation status and warnings
section of the HOME screen (see page 13).
To check the content of warning messages
Press the SELECT/ENTER dial on the control
panel. A popup window appears to display
messages for the current warnings.
Tip
Only one message is displayed at one time, even if
multiple warnings occur. The number of current errors
and warnings appears at the bottom of the popup
window. Be sure to check the messages for all errors and
warnings.
Example:
Popup window displaying warning message
"0007: REC INHIBIT MODE" (recording inhibit
mode)
dB
SDI SDI SDI SDI SDI SDI SDI SDI
0
-10
WARNING
-20
-30
-60
EMP EMP EMP EMP EMP EMP EMP EMP
EE
L R L R L R L R L R L R L R L R
1 2 3 4 5 6 7 8
0007 0007
REC INHIBIT MODE REC INHIBIT MODE
PLAY LOCK
TCR LTC INTRP DF
Rec Inhibit Mode
00 00
H M
O Error(s)/
REMAIN
16.5V ENCODE
STANDARD
10min
Indicates that there are no current
error messages (see page 52).
Indicates that there are three
current warnings.
To view the other messages, rotate the
SELECT/ENTER dial on the control panel.
When a warning message appears
Take any action that may be needed to eliminate
the cause of the warning.
SDI SDI SDI SDI SDI SDI SDI SDI
EMP EMP EMP EMP EMP EMP EMP EMP
L R L R L R L R L R L R L R L R
9 10 11 12 13 14 15 16
VTR OOOOO
EXT-LK KEYINHI
RECINHI
00 00
S F
3 Warning(s)
IN: --:--:--:--
LOCAL
F65RAW
EE
23.98P
21:46