Network Parameter Setting - Xerox Phaser 3160B User Manual

• MAC Address : Find the machine's MAC address from the
Network Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
• IP Address: Enter a new IP address for your printer.
For example, if your computer's IP address is 192.168.1.150,
enter 192.168.1.X. (X is number between 1 and 254 other than
the computer's address.)
• Subnet Mask: Enter a Subnet Mask.
• Default Gateway: Enter a Default Gateway.
6. Click Apply, and then click OK. The machine will automatically print
the Network Configuration Report. Confirm that all the settings are
correct.
7. Click Exit to close the SetIP program.
8. If necessary, restart the computer's firewall.
IP setting using SetIP Program (Macintosh)
For using SetIP program, disable the computer firewall before continuing
by performing the following:
1. Open System Preferences.
2. Click Security.
3. Click the Firewall menu.
4. Turn firewall off.
The following instructions may vary for your model.
1. Connect your machine to the network with a network cable.
2. Insert the Installation CD-ROM, and open the disk window, select
MAC_Installer > MAC_Printer > SetIP > SetIPapplet.html.
3. Double click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPapplet.html page that shows
the printer's name and IP address information.
4. Click on the icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter the machine's new information into the configuration window
as follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
• MAC Address : Find the machine's MAC address from the
Network Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
• IP Address: Enter a new IP address for your printer.
For example, if your computer's IP address is 192.168.1.150,
enter 192.168.1.X. (X is number between 1 and 254 other than
the computer's address.)
6. Select Apply, then OK, and OK again. The printer will automatically
IP setting using SetIP Program (Linux)
SetIP program should be automatically installed during the printer driver
installation.
1. Print the machine's network configuration report to find your
2. Open the /opt/Xerox/mfp/share/utils/.
3. Double click the SetIPApplet.html file.
4. Click to open the TCP/IP configuration window.
5. Enter the network card's MAC address, IP address, subnet mask,
6. The machine prints the network configuration report. Confirm all the
7. Close the SetIP program.

Network parameter setting

You can also set up the various network settings through the network
administration programs such as CentreWare IS.
Restoring factory default settings
You may need to reset the machine to the factory default settings when
machine that you are using is connected to new network environment.
Restoring factory default settings using CentreWare IS
1. Start a web browser such as Internet Explorer, Safari or Firefox and
2. When the CentreWare IS window opens, click Properties >
3. Click Reset. Then, click on the button below to restroe defaults.
4. Turn off and restart machine to apply settings.
Network Setup (Phaser 3160N only)_ 28
• Subnet Mask: Enter a Subnet Mask.
• Default Gateway: Enter a Default Gateway.
print the configuration report. Confirm that all the settings are correct.
Quit Safari. You may close and eject the installation CD-ROM. If
necessary, restart the computer's firewall. You have successfully
changed the IP address, subnet mask, and gateway.
machine's MAC address.
default gateway, and then click Apply.
When you enter the MAC address, enter it without a colon(:).
settings are correct.
enter your machine's new IP address in the browser window.
For example,
General.