Subscribe to Our Youtube Channel
Related Manuals for Alliance Laundry Systems 505828
Summary of Contents for Alliance Laundry Systems 505828
- Page 1 D311IE3A KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE. (If the dryer changes ownership, be sure this manual accompanies the dryer.) Part No. 505828 August 1999...
- Page 3 • Installation and service must be performed by a qualified installer or service agency. W257 © Copyright 1999, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher.
-
Page 4: Table Of Contents
Before You Call for Service ............... 21 If Service is Required ................. 21 Information for Handy Reference ............ 22 If replacement parts are required, contact the source Alliance Laundry Systems LLC where you purchased your dryer, or contact Shepard Street P.O. Box 990... - Page 5 10. Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product. 11. To reduce the risk of fire, DO NOT DRY plastics or articles containing foam rubber or similarly textured rubberlike materials. 505828...
-
Page 6: Important Safety Instructions
Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do not understand. 505828... -
Page 7: Tools
10.2 cm (4.0") (4.0") 1.1 cm (0.4") 71.1 cm 68.3 cm 59.7 cm (28") (26.9") (23.5") D312IE3H * WITH LEVELING LEGS TURNED INTO BASE For most installations, the basic tools you will need are: WRENCH SCREWDRIVERS LEVEL D074IE1K DUCT TAPE 505828... -
Page 8: Location Requirements
To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors. W116 NOTE: Failure to exhaust dryer properly will void D314IE0C D315IE0C warranty. DON'T NOTE: Venting materials are not supplied with the dryer (obtain locally). 505828... - Page 9 Connect Electrical Cord Consult Section on Electrical Requirements. D276IE1B D189IE1C Two-Wire Connection Three-Wire Connection NOTE: Dryer is shown with access cover removed for illustration purposes only. NEVER operate dryer with access cover removed. 505828...
-
Page 10: Wipe Out Inside Of Dryer
Close the loading door and start the dryer in a heat setting (refer to the Operating Instructions). After the dryer has operated for three minutes, the exhaust air or exhaust pipe should be warm. 505828... - Page 11 D272PE1B D271PE1C D268PE1D D273PE1D D269PE1G D276PE1D D270PE1D D274PE1C D275PE1C 505828...
- Page 12 5. Secure the strain relief to the power cord, or wires, reduce the risk of an electric shock, serious where they enter the dryer cabinet. injury or death, NEVER operate the dryer with the access cover removed. 6. Reinstall access cover and screw. W157 505828...
-
Page 13: Grounding Instructions
TERMINAL 3. Use the three screws from the envelope located in the cylinder to attach the power cord wires to the terminal block. 4. Tighten all screws and reinstall access cover removed in Step 1. “L2” TERMINAL D286IE0B 505828... - Page 14 260 sq. cm/open (40 sq. in./open) *Louvered door with equivalent air openings is acceptable. (Minimum clearances are shown.) ** NOTE: For new installations, locate top of wall vent 106.7 cm (42 inches) above floor to make venting easier to connect. 505828...
-
Page 15: Exhaust System Materials
Never install flexible duct in concealed spaces, such as accommodate on demand make-up air needs in the a wall or ceiling. home. These devices can be obtained through your building contractor or building material suppliers. D315IE0A D314IE0B DON'T 505828... -
Page 16: Exhaust System
7.3 m (24 feet) 6.1 m (20 feet) 6.1 m (20 feet) 4.9 m (16 feet) 4.9 m (16 feet) 3.7 m (12 feet) 3.7 m (12 feet) 2.4 m (8 feet) NOTE: Deduct 1.8 m (6') for each additional elbow. 505828... -
Page 17: Dryer Airflow
WATER COLUMN MANOMETER 1.5 cm(.6") EXHAUST D012IE0A DUCT D320I Reduced Clearance Elbow Installing the dryer in shallow closets can be accomplished by using an Elbow, Part No. 62688, which is one inch narrower than a standard venting elbow. D319IE0A 505828... -
Page 18: Energy Saving Tips
• Follow the care labels on FLAME RETARDANT, SCOTCH-GUARD™, etc., garments for the proper washing and drying. • If loads should be damp for ironing, turn timer knob to the ENERGY SAVER setting, marked with a dot ( ), in Automatic or Time Dry cycles. 505828... -
Page 19: Time Dry Cycle
NOTE: The timer knob will not advance as quickly in the AUTOMATIC cycles as it does in the TIME DRY cycle. The time it takes for the timer to advance depends on the type and size of the load being dried. 505828... -
Page 20: End Of Cycle Signal
D323IE1B 4. Close loading door. Dryer will not operate with the door open. D325IE1B D326IE1A 5. Select FABRIC SELECTOR. Follow garment manufacturer’s care labels for recommended temperature settings. 505828... -
Page 21: Care Of Your Dryer
If automatically in the event of an overload. After overload protector cycles again, remove the dryer from cooling, the overload protector will reset itself. Dryer use and call the service person to correct the problem. 505828... -
Page 22: Before Drying
If the filter is not in place, clothing CLEAN THE LINT FILTER BEFORE DRYING could fall into the front air duct and get into the EACH LOAD. exhaust system, causing damage to the motor. D321IE2B 505828... -
Page 23: Motor Overload Protector
If service is required, contact the nearest Factory Authorized Service Center. If you are unable to locate an authorized service center or are unsatisfied with the service performed on your dryer, write to: Alliance Laundry Systems Shepard Street P.O. Box 990 D324IE0C Ripon, WI 54971-0990... - Page 24 Alliance Laundry Systems LLC Shepard Street P.O. Box 990 Ripon, WI 54971-0990 Date Purchased Model Number Serial Number Dealer’s Name Dealer’s Address Phone Number Service Agency Service Agency Address Phone Number NOTE: Record the above information and keep your sales slip. Model and serial numbers are located on the nameplate.
- Page 25 505828...
- Page 26 505828...
Need help?
Do you have a question about the 505828 and is the answer not in the manual?
Questions and answers