Alliance Laundry Systems 512685R2 Installation & Operation Manual
  1. Manuals
  2. Brands
  3. Alliance Laundry Systems Manuals
  4. Dryer
  5. 512685R2
  6. Installation & operation manual
Alliance Laundry Systems 512685R2 Installation & Operation Manual

Alliance Laundry Systems 512685R2 Installation & Operation Manual

Alliance laundry systems stacked clothes dryer installation/operation manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Clothes Dryer
Para bajar una copia de estas instrucciones
en español, visite www.comlaundry.com.
Keep These Instructions for Future Reference.
(If this machine changes ownership, this manual must accompany machine.)
Stacked
Nonmetered and Metered
Electric and Gas Models
www.comlaundry.com
D009C
Part No. 512685R2
July 2007

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 512685R2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Alliance Laundry Systems 512685R2

Summary of Contents for Alliance Laundry Systems 512685R2

  • Page 1 Para bajar una copia de estas instrucciones en español, visite www.comlaundry.com. Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Stacked Nonmetered and Metered Electric and Gas Models www.comlaundry.com D009C Part No. 512685R2 July 2007...

  • Page 3: For Your Safety

    • A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance. • This appliance must not be installed in a bedroom or bathroom. 512685 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WARNING W033...

  • Page 4: Table Of Contents

    All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information...
  • Page 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Operation Instructions for Electronic Display Control Dryers... 35 Step 1: Clean Lint Filter... 35 Step 2: Load Laundry... 35 Step 3: Close Loading Door... 35 Step 4: Determine Proper Dryer ... 35 Step 5: Set Fabric Selector ...

  • Page 6: Safety Information

    NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information Important Safety Instructions Save These Instructions...
  • Page 7 21. If supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 22. Install this dryer according to the INSTALLATION INSTRUCTIONS.

  • Page 8: Installation

    23.5 in. 28 in. (59.7 cm) (71.1 cm) *With leveling legs turned into base. 3/8 in. N.P.T. Gas Connection © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installation 4 in. (10.2 cm) 26.9 in. (68.3 cm) ELECTRIC MODELS 15.5 in.

  • Page 9: Metered Models

    NOTE: Side, rear and bottom exhaust openings are 4 inch (10.2 cm) ducting. Gas models cannot be vented out left side of cabinet because of burner housing. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 4 in. (10.2 cm) 26.9 in.

  • Page 10: Before You Start

    Figure 1 NOTE: An 8 in. (20.32 cm) coin drawer is required for coin operated MDC and NetMaster models. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Additional Security Torx security screws are available (as optional equipment at extra cost) for securing both lower access panels to each dryer base.

  • Page 11: Installing The Dryer

    Dryer Top (Rear 24 Dryer Rear Dryer Top (Front 4 Exhaust Duct from Combustible Construction © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 No other fuel burning appliance should be installed in the same closet with the dryer.

  • Page 12: Step 2: Connect Dryer Unit Exhaust System

    © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 2: Connect Dryer Unit Exhaust System To reduce the risk of fire and combustion gas accumulation the dryer MUST be exhausted to the outdoors.
  • Page 13 • DO NOT install flexible duct in concealed spaces, such as a wall or ceiling. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 • Static pressure in exhaust duct should not be greater than .6 inches water column (1.5 cm),...

  • Page 14: Exhaust Direction

    Maximum length of 4 in. (10.2 cm) diameter flexible metal duct. NOTE: Deduct 6 feet (1.8 m) for each additional elbow. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Exhaust System For best drying results, recommended maximum length of exhaust system is shown in Table 1.

  • Page 15: Multi-Dryer Installation Exhaust Requirements

    CLEARANCE TO ROOF/GROUND 58786 Backdraft Damper (Available through your local authorized parts source) Clean Out Cover (Must be provided). Inspect monthly. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Figure 5 Installation METERED MODELS ILLUSTRATED...
  • Page 16 Figure 7 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT EXHAUST AIR FLOW MAXIMUM LENGTH OF DUCT 30 feet (9.1 m)

  • Page 17: Step 3: (Gas Dryer Only) Connect Gas Supply Pipe

    • Any disassembly requiring the use of tools must be performed by a suitably qualified service person. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 1. Make certain your dryer is equipped for use with the type of gas in your laundry room.

  • Page 18: Step 4: (Electric Dryer Only) Connect Electrical Plug

    For proper operation at altitudes above 3500 feet (1070 m) the L.P. gas valve spud orifice size must be reduced to ensure complete combustion. Refer to Table 3. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT L.P. Altitude Adjustments Altitude feet...

  • Page 19: Grounding Information

    Do not connect dryer to 110, 115, or 120 volt circuit. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 • Heating elements are available for field...
  • Page 20 FOUR-WIRE Typical Receptacle Power Cord Strain Relief Nut Strain Relief Figure 9 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT THREE-WIRE CONNECTION D275I D006I FOUR-WIRE CONNECTION NOTE: Dryer is shown with access cover removed for illustration purposes only. NEVER operate the dryer with access cover removed.

  • Page 21: Connecting Power Cord With Three-Wire Plug

    30 Ampere Fuses or Circuit Breaker Neutral Wire 1. Disconnect power to dryer. 2. Remove access cover from rear of dryer. Figure 12 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 POWER SUPPLY INTERMEDIATE FUSE BOX (may...

  • Page 22: Connecting Power Cord With Four-Wire Plug

    8. Reinstall access cover and screw. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Connecting Power Cord with Four-Wire Plug NOTE: Four-wire cord is required for mobile homes or where codes do not permit grounding through neutral.
  • Page 23 4. Use a strain relief and insert end of power cord through power supply hole. Figure 18 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 5. Attach power cord ground (green) wire to rear bulkhead using ground screw removed in Step 3.

  • Page 24: Step 5: Reverse Door, If Desired

    3. Pull bottom of door liner out, then pull down, removing door liner from door panel. Figure 22 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 4. Rotate door panel 180 degrees as shown. 5. Remove door strike from door liner and reinstall on opposite side.

  • Page 25: Step 6: Wipe Out Inside Of Dryer

    Figure 29 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Step 7: Plug In the Dryer Electric Dryer Connect the dryer to an electrical power source.

  • Page 26: Step 8: Recheck Steps 1-7

    Do not operate other appliances on the same circuit when this appliance is operating. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT WARNING To reduce the risk of an electric shock or...

  • Page 27: Gas Dryers

    Closed Position Shut-Off Valve Handle Air Shutter Lockscrew Air Shutter © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 After either dryer has operated for approximately five minutes, observe burner flame through lower front panel. Adjust the air shutter to obtain a soft, uniform blue flame.

  • Page 28: Vending

    Start button has not been pressed. The IN USE LED will be lit. The timer will not count down until the Start button is pressed. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Vending PERM PRESS...

  • Page 29: Topoffs

    LED three times separated by a one and a half second pause. This sequence is repeated as long as the Shorted Thermistor error is sensed. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Setting Dry Time Dipswitches To change the dry time on the dryer, combinations of dipswitches can be set on the control.

  • Page 30: Dipswitch Settings

    Vending Dipswitch Settings Heat Time Per Coin Pulse (in minutes) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Heat Switch Number Table 4 (continued) 512685...
  • Page 31 Cool Down Per Cycle (in minutes) 3 (preset at factory) Total Cycle Time = Heat Time + Cool Down Time © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Table 4 (continued) Heat Switch Number Cool Down Switch Number...

  • Page 32: Test Setting

    Then set them all to the off position. Refer to Figure 34. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 3. Plug in the machine and initiate a cycle. NOTE: With all the control dipswitches off, the total cycle time will be four minutes long.

  • Page 33: Slide Extension

    Figure 36 5. Torque nut between 2 and 2.26 Nm (18 and 20 inch-pounds), or tighten nut firmly. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 6. Install extension spring in bracket hole and hole in upper arm of lever.
  • Page 34 NOTE: To avoid long run-down time (45 minutes factory default) when testing operation, refer to Test Setting section. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Installing Extension Onto Coin Slide: Option 2 1. Install coin slide according to manufacturer’s instructions.

  • Page 35: Operation

    Step 1: Clean Lint Filter Clean lint filter before each use. D608I Figure 39 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Operation Step 2: Load Laundry Load clothes loosely into dryer drum. Add fabric softener sheet if desired.

  • Page 36: Copyright, Alliance Laundry Systems Llc – Do Not Copy Or Transmit

    CASUAL DELICATE NORMAL FABRIC SELECTOR Figure 43 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 6: Start Dryer Nonmetered Models Rotate timer knob to desired time setting (up to 60 minutes). Press the PUSH-TO-START button.

  • Page 37: Operation Instructions For Electronic Display Control Dryers

    IMPORTANT: To avoid damage to dryer, do not use more than one fabric softener sheet per load. Figure 47 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open.

  • Page 38: Step 5: Set Fabric Selector

    NOTE: Always follow manufacturer’s care label instructions. Figure 49 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 6: Insert Coin(s) or Card To Insert Money Insert coin(s) in coin slot. Check pricing as seen on digital display.

  • Page 39: Step 7: Start Dryer

    The PUSH START status word flashes at one-second intervals when activated. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 DRYING DRYING is lit to indicate that one of the heated cycles (HIGH TEMP, MED TEMP, LOW TEMP) is currently in operation.

  • Page 40: Operation Instructions For Mdc Dryers

    IMPORTANT: To avoid damage to dryer, do not use more than one fabric softener sheet per load. Figure 54 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open.

  • Page 41: Step 6: Insert Coin(S) Or Card

    Remove knits when slightly damp because overdrying may cause shrinkage. Do not tumble dry knit woolens. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Step 7: Start Dryer To start dryer, push START pad.

  • Page 42: Operation Instructions For Netmaster Dryers

    IMPORTANT: To avoid damage to dryer, do not use more than one fabric softener sheet per load. Figure 62 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open.

  • Page 43: Step 5: Set Fabric Selector

    To Insert Money Insert coin(s) in coin slot. Check pricing as seen on digital display. Figure 66 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 To Insert Card Insert card into opening. DO NOT remove the card until the REMOVE CARD LED is lit.

  • Page 44: Indicator Lights

    DRYING will turn off at the end of a heated cycle or when the COOL DOWN cycle begins. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT COOL DOWN COOL DOWN is lit whenever the COOL DOWN portion of a heated cycle is active.

  • Page 45: Maintenance

    Some spray pretreat products may harm the finish on the control panel. NOTE: The wiring diagram is located inside the control panel. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Maintenance Label all wires prior to disconnection when servicing controls.

  • Page 46: Lint Filter

    START pad. If overload protector cycles again, remove the dryer from use and call the service person to correct the problem. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT For Energy Conservation • Make sure the lint filter is always clean.

  • Page 47: Troubleshooting

    Dryer doesn’t dry clothes satisfactorily Dryer is noisy Clothes are too wrinkled Clothes have odor © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512685 Troubleshooting Possible Cause/Solution • Nonmetered models - Turn timer knob further into cycle.

  • Page 48: Contact Information

    If service is required, contact the nearest Factory Authorized Service Center. If you are unable to locate an authorized service center or are unsatisfied with the service performed on your dryer, contact: Alliance Laundry Systems Shepard Street P. O. Box 990 Ripon, WI 54971-0990 U.S.A.

  • Page 50: Installer Checklist

    (Refer to the manual for more detailed information) • Position and Level the Dryer. LEVEL D255I D255I CHECK • Connect Dryer Exhaust System. CHECK GAS ONLY • Connect Gas Supply Pipe Hoses. • Check for Gas Leaks. CHECK ELECTRIC ONLY •...

Table of Contents

Save PDF