Connections; Connecting Antenna/Cable - Daewoo DVR-S05 User Manual

Rear panel
!
! AC Power Cord
Plug into a power outlet.
AUDIO OUT (L, R)
@
Connect to a TV or other equipment with audio
inputs.
COMPONENT/PROGRESSIVE VIDEO OUT (Y Pb Pr)
#
Connect to a TV with Component Video (Y Pb Pr)
inputs.
$ AV OUT (VIDEO, L-AUDIO-R)
Connect to a TV with video and audio inputs.
% LINE2 (VIDEO, L-AUDIO-R)
Connect to the audio/video outputs of an external
source (VCR, Camcorder, etc.).
Caution
• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage
to the DVD Recorder+VCR.
10
Identification of Controls
@ # $% ^
DVD & VCR OUT
ANT. IN
AUDIO OUT COMPONENT OUT OUT LINE 2
Pr
R R
AUDIO
S-VIDEO
L Pb L
OUT
COAXIAL
DIGITAL Y
VIDEO
AUDIO OUT
RF OUT
( * &
^ RF IN (FROM ANT.)
Connect to your antenna or cable TV outlet.
RF OUT (TO TV)
&
Connect to a TV with an RF coaxial input.
COAXIAL (Digital Audio Out)
*
Connect to an amplifier with a coaxial digital
audio input.
( S-VIDEO OUT
Connect to a TV with an S-Video Input.

Connections

Connections
• There are a variety of ways to connect the DVD Recorder+VCR to your TV and other equipment. Use only one of
the connections described below. Whichever TV connection you use will work with all input sources.
• Please refer to the manuals for your TV, VCR, stereo system, or other devices as necessary to make the best
connections.
• For better sound reproduction, connect the DVD Recorder+VCR's AUDIO OUT jacks to the audio in jacks of your
amplifier, receiver, stereo, or audio/video equipment. See 'Connecting an Amplifier/Receiver' on page 13.
Caution
• Make sure the DVD Recorder+VCR is connected directly to the TV, and the TV is set to the correct video input.
• Do not connect the DVD Recorder+VCR's AUDIO OUT jack to the phono in jack (record deck) of your audio system.
• Do not connect the DVD Recorder+VCR via your VCR. The DVD image could be distorted by the copy protection
system.

Connecting Antenna/Cable

1
Disconnect the antenna/cable from the rear of your
TV.
2
Connect this cable to the jack marked RF IN (FROM
ANT.) on the rear panel of the DVD Recorder+VCR.
Cable Service Without Cable Box
If your cable wire is connected to your TV without a
converter or descrambler box, unscrew the wire from your TV and attach it to the RF IN (FROM ANT.) jack on the
rear panel of the DVD Recorder+VCR.
Use the supplied coaxial cable to connect between the DVD Recorder+VCR's OUT (TO TV) jack and the antenna
input jack on your TV. With this connection, you can receive all midband, superband, and hyperband channels
(all cable channels).
Cable Service With Cable Box
If a cable box is required in your cable system, follow
the instructions shown at right. This hookup permits
both TV and DVD Recorder+VCR operation.
To view or record a CATV channel:
1
Tune the TV to the correct video input channel.
2
Set the DVD Recorder+VCR to the output channel of
the cable box using the [CH .../†] or the [0-9] keys
on your DVD Recorder+VCR (e.g., CH3).
3
Select the channel you wish to view on the cable
box.
• If you are using a cable box to tune channels, it is not necessary to run Auto Channel Search as indicated on page
18.
Antenna Antenna
Cable TV
Wall Jack
Flat Wire
(300 ohm)
300/75 ohm
OR OR
Adaptor
(Not supplied)
DVD & VCR OUT
OUT LINE 2
AUDIO OUT COMPONENT OUT
Pr
R R
AUDIO
DEO
Pb
L L
T
COAXIAL
DIGITAL Y
VIDEO
AUDIO OUT
Rear of DVD Recorder+VCR
Cable TV
Wall Jack
Back Panel of
Typical Cable Box
DVD & VCR OUT
AUDIO OUT COMPONENT OUT OUT LINE 2
Pr
R R
AUDIO
EO
L Pb L
T
COAXIAL
DIGITAL Y
VIDEO
AUDIO OUT
Rear of DVD Recorder+VCR
ANT. IN
RF OUT
ANT. IN
RF OUT
11