Related Manuals for Planet ISW-621 Series
Summary of Contents for Planet ISW-621 Series
- Page 1 4-Port 10/100Mbps +1/2 100FX Fiber Port Industrial Fast Ethernet Switch ISW-511 / ISW-621Series User's Manual...
-
Page 2: Fcc Warning
Trademarks Copyright © PLANET Technology Corp. 2009. Contents subject to revision without prior notice. PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective owners. Disclaimer PLANET Technology does not warrant that the hardware will work... -
Page 3: Ce Mark Warning
Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET 4-Port 10/100Mbps +1/2 100FX Fiber Port Industrial Fast Ethernet Switch User’s Manual For Models: ISW-511 / ISW-621 Series Revision: 1.0 (February, 2009) Part No: EM-ISW-511_621_v1.0 (2350-AH0150-000) -
Page 4: Table Of Contents
TABLE OF CONTENTS 1. INTRODUCTION ................ 6 1.1 Package Contents ............... 6 1.2 How to Use This Manual ............. 6 1.3 Product Features ..............7 Physical Port ............... 7 Layer 2 Features ..............7 Industrial Case / Installation ..........8 1.4 Product Specifications ............ - Page 5 4. SWITCH OPERATION ..............24 4.1 Address Table ..............24 4.2 Learning ................24 4.3 Forwarding & Filtering ............24 4.4 Store-and-Forward .............24 4.5 Auto-negotiation ..............25 5. TROUBLESHOOTING ..............26 APPENDIX A: NETWORKING CONNECTION ........27 A.1 Switch’s RJ-45 Pin Assignments ..........27 A.2 RJ-45 cable Pin Assignments ..........27...
-
Page 6: Introduction
1. INTRODUCTION 1.1 Package Contents Check the contents of your package for following parts: ● Industrial Fast Ethernet Switch x 1 ● User's Manual x 1 ● DIN Rail Kit x 1 ● Wall Mount Kit x 1 If any of these are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the original packing material, and use them against to repack the product in case there is a need to return it to us for repair. -
Page 7: Product Features
802.3x PAUSE frame flow control (Full-Duplex) □ Backplane (Switching Fabric): ISW-511 Series: 1Gbps, ISW-621 Series: 1.2Gbps □ Integrated address look-up engine, support 2K absolute MAC addresses □ 1Mbit on-chip frame buffer on ISW-511 / ISW-621 Series □ Automatic address learning and address aging... -
Page 8: Industrial Case / Installation
□ -10 to 60 Degree C operation temperature on ISW-511 / ISW- 511S15 / ISW-621 / ISW-621S15 □ -40 to 75 Degree C operation temperature on ISW-511T / ISW- 511TS15 / ISW-621T / ISW-621TS15... -
Page 9: Product Specifications
1.4 Product Specifications Model ISW-511 ISW-511S15 Hardware Specification Ports 4 x 10/100Base-TX, Auto-negotiation, Auto-MDI/MDI-X Copper 10Base-T: 2-pair UTP Cat. 3, 4, 5 cable (100meters, max.) Cable 100Base-TX: 2-pair UTP Cat. 5 cable (100meters, max.) Port 1 x 100Base-FX Cable 50/125μm or 62.5/125μm fiber 9/125μm fiber Fiber Optical Mode... - Page 10 Model ISW-511T ISW-511TS15 Hardware Specification Ports 4 x 10/100Base-TX, Auto-negotiation, Auto-MDI/MDI-X Copper 10Base-T: 2-pair UTP Cat. 3, 4, 5 cable (100meters, max.) Cable 100Base-TX: 2-pair UTP Cat. 5 cable (100meters, max.) Port 1 x 100Base-FX Cable 50/125μm or 62.5/125μm fiber 9/125μm fiber Fiber Optical Mode...
- Page 11 Model ISW-621 ISW-621S15 Hardware Specification Ports 4 x 10/100Base-TX, Auto-negotiation, Auto-MDI/MDI-X Copper 10Base-T: 2-pair UTP Cat. 3, 4, 5 cable (100meters, max.) Cable 100Base-TX: 2-pair UTP Cat. 5 cable (100meters, max.) Port 2 x 100Base-FX Cable 50/125μm or 62.5/125μm fiber 9/125μm fiber...
- Page 12 Model ISW-621T ISW-621TS15 Hardware Specification Ports 4 x 10/100Base-TX, Auto-negotiation, Auto-MDI/MDI-X Copper 10Base-T : 2-pair UTP Cat. 3, 4, 5 cable (100meters, max.) Cable 100Base-TX : 2-pair UTP Cat. 5 cable (100meters, max.) Port 2 x 100Base-FX Cable 50/125μm or 62.5/125μm fiber 9/125μm fiber Fiber Optical Mode...
-
Page 13: Installation
ISW-511 / ISW-621 series. 2.1 Product Description The PLANET ISW-511 / ISW-621 series is 4-Port 10/100Mbps + 1/2 100FX Fiber Port Industrial Fast Ethernet Switch with non-blocking wire- speed performance and new slim type with IP 30 metal shape for easily deployment in Heavy Industrial demanding environments. -
Page 14: Switch Front Panel
2.1.1 Switch Front Panel Figure 2-1 & 2-2 & 2-3 & 2-4 shows a front panel of Industrial Fast Ethernet Switch. Figure 2-1 ISW-511 / ISW-511S15 front panel Figure 2-2 ISW-621 / ISW-621S15 front panel... - Page 15 Figure 2-3 ISW-511T / ISW-511TS15 front panel Figure 2-4 ISW-621T / ISW-621TS15 front panel...
-
Page 16: Led Indicators
2.1.2 LED Indicators Color Function Green Lit: indicate the power 1 has power. Green Lit: indicate the power 2 has power. Lit: indicate the either power 1 or power 2 has no FAULT Green power. Lit: indicate the Fiber port is successfully Fiber Green connecting to the network at... -
Page 17: Wiring The Power Inputs
2.1.4 Wiring the Power Inputs The 6-contact terminal block connector on the top panel of Industrial Fast Ethernet Switch is used for two DC redundant powers input. Please follow the steps below to insert the power wire. 1. Insert positive / negative DC power wires into the contacts 1 and 2 for POWER 1, or 5 and 6 for POWER 2. -
Page 18: Wiring The Fault Alarm Contact
2.1.5 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. Inserting the wires, the Industrial Fast Ethernet Switch will detect the fault status of the power failure, or port link failure (available for managed model) and then forms an open circuit. -
Page 19: Mounting Installation
2.2 Mounting Installation This section describes how to install the Industrial Fast Ethernet Switch and make connections to it. Please read the following topics and perform the procedures in the order being presented. In the installation steps below, this Manual use IGS- 801 (PLANET 8 Port Industrial Gigabit Switch) as the example. - Page 20 Step 2: Lightly press the button of DIN-Rail into the track. Step 3: Check the DIN-Rail is tightly on the track. Step 4: Please refer to following procedures to remove the Industrial Fast Ethernet Switch from the track. Step 5: Lightly press the button of DIN-Rail for remove it from the track.
-
Page 21: Wall Mount Plate Mounting
2.2.2 Wall Mount Plate Mounting To install the Industrial Fast Ethernet Switch on the wall, please follows the instructions described below. Step 1: Remove the DIN-Rail from the Industrial Fast Ethernet Switch; loose the screws to remove the DIN-Rail. Step 2: Place the wall mount plate on the rear panel of the Industrial Fast Ethernet Switch. -
Page 22: Application
3. AppLICATION In this paragraph, we will describe how to install Industrial Fast Ethernet Switch and the installation points for the attention. Fiber Switch ISW-511S15 15km 15km Serial Device ISW-511S15 Server 15km ICA-525 Control Center ICA-651 ICA-350 ICS-2100 ISW-511S15 ICS-2100 Harbor Warehouse ICA-310 Robot... -
Page 23: Installation Steps
Installation Steps Step 1: Unpack the Industrial Fast Ethernet Switch. Step 2: Check the DIN-Rail is screwed on the Industrial Fast Ethernet Switch. (Please refer to DIN-Rail Mounting section for DIN- Rail installation. If the DIN-Rail is not screwed on the Industrial Fast Ethernet Switch.). -
Page 24: Switch Operation
4. SwITCh OpeRATION 4.1 Address Table The Industrial Fast Ethernet Switch is implemented with an address table. This address table composed of many entries. Each entry is used to store the address information of some node in network, including MAC address, port no, etc. This information comes from the learning process of Industrial Fast Ethernet Switch. -
Page 25: Auto-Negotiation
Therefore, no error packets occurrence, it is the best choice when a network needs efficiency and stability. The Industrial Fast Ethernet Switch scans the destination address from the packet-header, searches the routing table provided for the incoming port and forwards the packet, only if required. The fast forwarding makes the switch attractive for connecting servers directly to the network, thereby increasing throughput and availability. -
Page 26: Troubleshooting
5. TROUBLeShOOTING This chapter contains information to help you solve issues. If the Industrial Fast Ethernet Switch is not functioning properly, make sure the Industrial Fast Ethernet Switch was set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Fast Ethernet Switch. -
Page 27: Appendix A: Networking Connection
AppeNDIX A: NeTwORKING CONNeCTION A.1 Switch’s RJ-45 Pin Assignments 10/100Mbps, 10/100Base-TX RJ-45 Connector pin assignment MDI-X Contact Media Dependant Interface Media Dependant Interface -Cross Tx + (transmit) Rx + (receive) Tx - (transmit) Rx - (receive) Rx + (receive) Tx + (transmit) 4, 5 Not used Rx - (receive) Tx - (transmit) - Page 28 Straight Cable SIDE 1 SIDE 2 SIDE 1 1 2 3 4 5 6 7 8 1 = White/Orange 1 = White/Orange 2 = Orange 2 = Orange 3 = White/Green 3 = White/Green 4 = Blue 4 = Blue 5 = White/Blue 5 = White/Blue 1 2 3 4 5 6 7 8...
Need help?
Do you have a question about the ISW-621 Series and is the answer not in the manual?
Questions and answers