Page 4
Preface (This page intentionally left blank.) System Manual Color Coronis 2MP...
Page 5
BarcoView software products are the property of BarcoView. They are distributed under copyright by Barco N.V. or BarcoView, LLC., for use only under the specific terms of a software license agreement between Barco N.V. or BarcoView LLC. and the licensee. No other use, duplication, or disclosure of a BarcoView software product, in any form, is authorized.
Page 6
Disposal Information The lamps inside the display contain mercury. Do not throw the display in the trash. Dispose of it as required by local ordinances or regulations. System Manual Color Coronis 2MP...
After unpacking the display ........33 Power connection ..........36 Video connection..........37 USB connection........... 40 RS-232 connection ..........41 Cable routing............42 Attaching the display to an arm stand ....44 Installing the software ......... 46 System Manual Color Coronis 2MP...
Page 8
Table of Contents Software Installation ........... 47 Using the BarcoMed Product Installation Wizard . 47 BARCO DPMS Screen Saver Installation .... 53 Barco monitor plug and play software....55 Display Controller settings ......59 BarcoMed Driver Tab ..........61 Introduction............61 Languages supported ........
Page 9
Use As Logon Screen Saver ......74 Getting started with the BARCO DPMS Screen Saver ..........74 Using the BARCO DPMS Screen Saver ....75 Installing or Reinstalling BARCO DPMS ....79 BARCO Display Tab ..........82 Introduction ............82 Using The BARCO Display Tab .......
Page 10
Reinstalling or Updating your BarcoMed 2MP2CF-3D Driver ............133 Uninstalling the BarcoMed 2MP2CF-3D driver..135 Uninstalling the BarcoMed 2MP2CF-3D driver..135 Technical Information ........139 Technical specifications........141 Connector pin assignments ......... 144 Glossary .............. 146 Warranty Statement ........149 System Manual Color Coronis 2MP...
Power connection • Power requirements: The apparatus must be powered using the 12 VDC power supply that is supplied with the apparatus. • The 12 VDC power supply must be powered by the AC mains voltage. System Manual Color Coronis 2MP...
Page 12
3 monitors. If you use an unstable cart or stand, the set may fall, causing serious injury to a child or adult, and serious damage to the equipment. More warnings in the Installation chapter. System Manual Color Coronis 2MP...
Page 13
Safety Instructions This apparatus conforms to: CE, IEC 60950, UL 60950, CAN/CSA C22.2 No. 950-95 (cUL) System Manual Color Coronis 2MP...
UL regulations Indicates the display is approved according to the c-UL regulations Indicates the USB connectors on the display Symbols used throughout the manual: Important notice or remark Warning or caution Hint, tip System Manual Color Coronis 2MP...
DICOM standards without administrator intervention. Ambient Light Compensation (ALC) When enabled, the ALC system automatically adapts the display light output, depending on the ambient light in System Manual Color Coronis 2MP...
24-bit True Color for medical viewing applications. Minimum system requirements • Pentium 4 or compatible processor • 256MB of system memory (minimum) for optimum performance consult your application provider for their recommended minimum system memory requirements System Manual Color Coronis 2MP...
Display properties control panel to dynamically change display settings • Control panel supports the English (U.S.), Dutch, German, Korean, Japanese, Simplified Chinese and Traditional Chinese languages • Displays VGA boot messages on Color Coronis displays. System Manual Color Coronis 2MP...
• 1024 x 1280 @ 59 Hz, 24-bit true color The following resolution is also available on head 1 when the OS is booted in VGA mode. • 640x480 @ Default Refresh Rate, 16 colors System Manual Color Coronis 2MP...
Two velcro strips to bind the cables • European power cord • American power cord • Chinese power cord If some of the items are missing, please contact the reseller from whom you have purchased the unit. System Manual Color Coronis 2MP...
The control wheel can be pushed like a push button and turned like a knob. It allows to put the display in stand-by, navigate through the on-screen display (OSD) menus and change values in the OSD. System Manual Color Coronis 2MP...
Page 23
& swivel mechanism during transport. After unpacking, you should remove this strap. Do not throw the strap away! Should the display have to be packed and shipped later, the strap must be applied to the foot again. System Manual Color Coronis 2MP...
Page 24
Amplitude: 500 mV to 4V 6. USB downstream port USB 1.1 standard is supported. When the display is connected to the PC USB bus, you can connect USB devices, such as keyboard, mouse, digital camera, to this connector. System Manual Color Coronis 2MP...
Page 25
In that case, the RS-232 input of the first display must be connected to a PC COM port. 10. RS-232 input (D-Sub 9 female) Connect this connector to a PC COM port if you wish to control the display via RS-232. System Manual Color Coronis 2MP...
Page 26
Parts, controls and connectors System Manual Color Coronis 2MP...
Place the display on a strong and stable table or desk. • Keep the display away from heat sources and provide enough ventilation around the display. • Do not scratch or apply pressure to the LCD panel. This may damage the panel permanently. System Manual Color Coronis 2MP...
Figure 4: The BarcoMed 2MP2CF-3D display controller Install the BarcoMed 2MP2CF-3D controller in your computer following these steps: 1. Turn off the power to your computer and disconnect the power cord, however make sure that the computer chassis is still grounded. System Manual Color Coronis 2MP...
Page 31
5). For a dual-headed BarcoMed 2MP2CF-3D setup, connect the secondary display to the other connector on the display controller. 6. Reconnect the power cord, turn on the power, and boot the system as usual. System Manual Color Coronis 2MP...
Page 32
Display Controller installation Figure 5 System Manual Color Coronis 2MP...
3. Keep the strap in case the display needs to be shipped later. Adjust the panel orientation You can change the orientation of the panel at any time, but it is more convenient to select landscape or portrait orientation before connecting the cables. System Manual Color Coronis 2MP...
Page 34
2. Very important: Tilt the panel before changing the orientation. Should you change the panel orientation without tilting it first, you might irreversibly damage the tilt & swivel mechanism. Figure 7 3. To change from portrait to landscape, turn the panel counterclockwise. System Manual Color Coronis 2MP...
Page 35
“Orientation” in the OSD Geometry menu is set to “Automatic”. To change the orientation of the image, you will have to change the resolution in the Windows Display control panel (if possible). System Manual Color Coronis 2MP...
2. Connect the output of the 12V DC power supply to the DC input of the display. Figure 9 3. Connect one end of the proper power cable to the AC input of the 12V DC power supply. Figure 10 System Manual Color Coronis 2MP...
Note: In a Coronis system, the video source is the BarcoMed display controller. In that case, only DVI signal connection is applicable. System Manual Color Coronis 2MP...
Page 38
Proceed as follows: 1. Connect one end of the VGA cable to the D15 input of the display. 2. Connect the other end of the VGA cable to the analog video output of your computer. System Manual Color Coronis 2MP...
Page 39
2. Connect the Video signal to the display’s BNC input labeled “Video”. 3. Connect the horizontal or composite sync signal to the display’s BNC input labeled “HS/CS”. 4. Connect the vertical sync signal to the display’s BNC input labeled “VS”. System Manual Color Coronis 2MP...
To connect the USB cable: 1. Connect the display’s USB upstream connector to the USB port of the PC. 2. Connect any USB device to any of the display’s USB downstream connectors. System Manual Color Coronis 2MP...
2. Connect the other end of the RS-232 cable to the display’s RS232 IN connector. 3. If the system contains more than one display, connect the first display’s RS232 OUT connector to the following display’s RS232 IN connector. System Manual Color Coronis 2MP...
To put the foot cover in place: 1. Push the upper side of the cover onto the foot, so that the hooks inside the cover are positioned right under the bulges at the rear of the foot. System Manual Color Coronis 2MP...
Page 43
Display installation Figure 17 2. Slide the cover upward while moving the lower side of the cover towards the foot. 3. Press the cover to the foot so that it makes a clicking sound. System Manual Color Coronis 2MP...
2. Remove the tilt & swivel foot cover. 3. Remove the small screw (A) fixing the small plastic cover on top of the foot. Next, remove the small cover itself. System Manual Color Coronis 2MP...
Page 45
6. Remove the four screws fixing the foot while supporting the foot. 7. Attach the arm stand firmly to the panel using 4 screws M4 x 8 mm. 4 screws M4 x 8mm Figure 19 System Manual Color Coronis 2MP...
2. Connect the Color Coronis display panel(s) to the BarcoMed 2MP2CF-3D display controller and power supply. 3. Decide if you want to install the Barco DPMS Screen Saver Software in addition to the driver. Using the BarcoMed Product Installation Wizard...
Page 48
If it determines that the Microsoft Installer is either out of date or missing, it will display the screen shown in figure 21 below. Click “OK” to continue, the wizard will then install a newer version of the System Manual Color Coronis 2MP...
Page 49
If you do not want to install a particular BarcoMed Software product at this time, deselect it by clearing the checkbox next to it. 5. Click “Install” to continue or “Cancel” to exit the wizard. System Manual Color Coronis 2MP...
“Finish” or “Cancel”. Select the device you want to install and then click “Next”. Caution: You can install the driver for only one type of BarcoMed device at a time. If you have multiple types of BarcoMed devices installed in your computer, System Manual Color Coronis 2MP...
Page 51
Click “OK” to continue. 8. When the screen shown in figure 24 on page 52 or figure 25 on page 52 appears, click “Yes” or “Continue Anyway” to continue. This screen may appear multiple times. System Manual Color Coronis 2MP...
Page 52
When the Driver Install Wizard tells you that it has successfully installed the selected driver, click “Finish”. The wizard will now begin installing the next selected piece of BarcoMed Software. If you are working with System Manual Color Coronis 2MP...
Note: Clicking “Cancel” will also return you to the BarcoMed Product Install Wizard, but will not delete the Barco Display Driver. The wizard will also begin to install the next selected piece of BarcoMed Software. If the Wizard failed to successfully install the selected driver, it will warn you that the installation failed.
Page 54
12. The “Ready to Install Program” page will now appear, click “Install” to install DPMS or “Back” if you wish to change any of your DPMS installation settings. During installation the wizard will display a progress screen. System Manual Color Coronis 2MP...
Installing the software 13. When the Windows Installer has finished installing DPMS, the “InstallShield Wizard Completed” page will appear, click “Finish” to exit the BARCO DPMS InstallShield Wizard and return to the BarcoMed Product Install Wizard Welcome Screen. After returning to the BarcoMed Product Install Wizard Welcome Screen, the wizard will clear the checkbox next to DPMS Screen Saver.
Page 56
Figure 27: Windows 2000 Digital Signature Not Found Warning Figure 28: Windows XP Windows Logo Testing Warning The Barco Monitor Plug and Play software will automatically set the resolution for the displays of your Color Coronis System. However, the second head of a dual headed system may be inactive.
Page 57
Installing the software your panels please turn to the section “Display resolution” on page 131 of the Troubleshooting Section of this manual for instructions on setting the resolution. System Manual Color Coronis 2MP...
Page 58
Installing the software System Manual Color Coronis 2MP...
BarcoMed Tabs of the Windows Display Control Panel to change any display settings. 1. Open the “Display Properties Control Panel” by right clicking on the desktop, then select “Properties”. System Manual Color Coronis 2MP...
BarcoMed Display Controller, driver, and the currently selected display resolution. Graphics Board This displays the current BarcoMed Display Controller. Driver Version This displays the current BarcoMed driver version. Resolution This displays the currently selected display resolution. System Manual Color Coronis 2MP...
This option allows you to enable or disable the Direct-3D and OpenGL support of the BarcoMed 2MP2CF-3D. If you disable 3D, 3D operations will not be accelerated by the hardware, resulting in significant performance loss. System Manual Color Coronis 2MP...
BarcoMed Driver Tab Monitor Configuration If the options in this section are grayed out, then they are not available for the model controller with which you are working. System Manual Color Coronis 2MP...
PCI and Firm- 1MP2FH ware Information PCI Information 2MP1 Only PCI Information 2MP1NT Only PCI Information 2MP2 Only PCI and Firm- 2MP2H ware Information PC and Firmware 2MP2CF–3D Information PCI and Firm- 2MP2FH ware Information System Manual Color Coronis 2MP...
2. Click on the “Settings” tab. Double click on the rectangle that represents one of the heads of the BarcoMed Display Controller you are working with to bring up its properties page. Click on the “BarcoMed Hardware Tab” (see figure 30 on page 67). System Manual Color Coronis 2MP...
BarcoMed Hardware Tab Figure 30 Device Displays the current BarcoMed Display Controller, driver, and the currently selected display resolution. System Manual Color Coronis 2MP...
“Advanced ...” Button: By clicking on this button, the user can display more information about the BarcoMed Display Controller installed in the selected PCI slot. “Generate Report” Button: Clicking this button will produce two reports. It will first run the Windows System Manual Color Coronis 2MP...
Page 69
BarcoMedSystemReport.txt. The other report that is generated contains information about the Barco display adapters installed in the system and will be named BarcoMedDeviceInfo.txt. This report will be saved on the desktop.
DPMS states as requested by the display controller. The default state for the BARCO DPMS Screen Saver is the Off state. In addition to simply entering the Off state after the work day, the user can specify that the display first go through two other DPMS Screen Saver states before going into Off state.
(Stand-By, Suspend, or Off) by the display controller during user inactivity. Screen Saver During Work Day On CRT based displays, such as the Barco MGD series, a “regular” screen saver can be invoked during user inactivity during the work day. This “regular” screen saver and its settings can be chosen from the “Screen...
Barco DPMS Screen Saver Saver During Work Day” section. We recommend using an all black screen saver, such as the “Barco Blank Screen” saver, for the longest phosphor life. On LCD based displays, such as the Barco CORONIS displays, it is not necessary to invoke a screen saver as there is no CRT phosphor to preserve.
If you have a Barco Medical Display, select “Barco Quick Start.” If a non-Barco display is being used, select the amount of time it takes your display to warm up via the “Monitor Setting”...
Barco DPMS Screen Saver Use As Logon Screen Saver Check the box to use the BARCO DPMS Screen Saver when no one is logged into the system. Uncheck the box to use the default screen saver when no one is logged into the system.
Barco DPMS Screen Saver so that Windows will store the selection in the user’s profile. If a user does not select the BARCO DPMS Screen Saver as his screen saver, the next time he logs on to the system the screen saver selection may be blank.
Page 76
Barco DPMS Screen Saver Figure 31: Windows 2000 Screen Saver Tab Figure 32: Windows XP Screen Saver Tab System Manual Color Coronis 2MP...
Page 77
Barco DPMS Screen Saver 2. Click on the “Settings” button. The “BARCO DPMS Screen Saver Control Panel” will open (see figure 33). Figure 33: BARCO DPMS Settings Control Panel 3. Use the default schemes by selecting one of the three default schemes.
Page 78
“Properties” from the drop down menu; then select the “Screen Saver” tab. 2. Select the “BARCO DPMS Screen Saver” in the “Screen Saver” drop down menu if it is not already selected.
Off state. 8. Select the amount of time it takes for your display to warm up. If you have a Barco Medical Display, select “Barco Quick Start”. If you are using a non-Barco display, select the amount of time it takes your display to warm up via the “Monitor Setting”...
Page 80
1. Select only the DPMS Screen Saver on the BarcoMed Product Install Wizard’s welcome screen and click “Install”. 2. Click “Next” on the Welcome Screen of the BARCO DPMS InstallShield Wizard to begin the installation. 3. Select the radio button next to “Remove” on the Program Maintenance screen of the Wizard and click “Next”.
Page 81
Barco DPMS Screen Saver Figure 35 5. When the Wizard has finished removing the program, click “Finish” on the InstallShield Wizard Completed Screen of the Wizard. 6. Click “Quit” to exit the BarcoMed Product Installation Wizard. System Manual Color Coronis 2MP...
BARCO Display Tab BARCO Display Tab Introduction The BARCO Display Tab is used for gathering information about the BarcoMed Flat Panel Display(s). To access the BARCO Display Tab do the following: 1. Open the “Display Properties Control Panel” by right clicking on the desktop, then select “Properties”.
Using The BARCO Display Tab Displays All of the available display adapters that are of the same type as the current barco display adapter are shown here graphically, with one display icon representing each port of a display adapter. The icon orientation reflects the display resolution.
Page 84
I-Guard sensor on the front of the display. Current Luminance Value: This is the current luminance value of the display. It may vary a bit from time to time, for the display continuously calibrates itself to meet the target luminance value. System Manual Color Coronis 2MP...
Page 85
BARCO Display Tab Figure 37 System Manual Color Coronis 2MP...
Page 86
BARCO Display Tab System Manual Color Coronis 2MP...
The LED turns orange. Push and hold BARCO Figure 38 When the display is in stand-by, press control wheel to switch it back on. System Manual Color Coronis 2MP...
The following functions are present in analog mode but are not present in digital (DVI) mode: • Autoset • Video Contrast • Video Brightness • Preset This is indicated throughout this manual. System Manual Color Coronis 2MP...
1. Turn the control wheel to select Yes (to save the changes) or No (if you do not wish to save the changes). 2. Click the control wheel to confirm the choice. Using the Autoset function * Not available in DVI mode System Manual Color Coronis 2MP...
Page 92
(0% video amplitude) and parts that are full white (100% video amplitude). To perform Autoset: 1. Turn the control wheel to display the on-screen display. The Main Menu appears. The Autoset menu is selected. System Manual Color Coronis 2MP...
2. Turn the control wheel to select Adjustments. 3. Click the control wheel to enter the Adjustments menu. 4. Turn the control wheel to select Geometry. 5. Click the control wheel to enter the Geometry menu. System Manual Color Coronis 2MP...
Auto: The OSD orientation auto- matically follows the orientation of the display Portrait: The OSD is displayed in portrait orientation Landscape: The OSD is displayed in landscape orientation Contrast adjustment This adjustment is not necessary (and not available) System Manual Color Coronis 2MP...
Contrast menu. 2. Turn the wheel to select Contrast CAL Pos. 3. Click the wheel to switch to calibrated position. Additional information If you change Contrast manually, the changed value is saved in the memory. System Manual Color Coronis 2MP...
Video Brightness menu. To return to calibrated position: 1. Proceed as described above to enter the Video Brightness menu. 2. Turn the wheel to select Brightness CAL Pos. 3. Click the wheel to switch to calibrated position. System Manual Color Coronis 2MP...
The native, unmodified color temperature of the panel. This setting also results in the maximum possible luminance on the LCD panel 7. Click the control wheel to confirm the selection and return to the menu. System Manual Color Coronis 2MP...
Page 98
Then turn the wheel to change the value. At last, click the wheel again to confirm the change. 10. Exit the menus. Notes: • The Native White color temperature cannot be modified. System Manual Color Coronis 2MP...
Page 99
6. Turn the control wheel to select the color temperature you wish to reset. 7. Click and hold the control wheel for approximately two seconds. 8. Turn the control wheel to select Factory Reset Color Temp. 9. Turn the wheel to select Proceed. System Manual Color Coronis 2MP...
Color Temperature ClearBase Automatic Menu Exit EXIT 4. Turn the control wheel to select User Controls. 5. Click the control wheel to switch from “On” to “Off”. 6. Exit the menus and save the changes. System Manual Color Coronis 2MP...
Page 101
Color Temperature ClearBase Automatic Menu Exit EXIT 7. Turn the control wheel to select User Controls. 8. Click the control wheel to switch from “Off” to “On”. 9. Exit the menus and save the changes. System Manual Color Coronis 2MP...
Rename the current Preset or select another Preset that matches the characteristics of the selected video signal Information Read information about the dis- play and the selected video sig- Autoset The Autoset menu is not available in DVI mode. System Manual Color Coronis 2MP...
Page 103
15% video amplitude. E.g., a Windows desktop pattern would be a good image, provided the background is not too dark. • Automatic Phase: The image should contain sharp black-white transitions, like a line pattern or characters. System Manual Color Coronis 2MP...
Page 104
Switch to calibrated position of contrast Man Contrast adj Manually adjust contrast Video Brightness This menu is not available in DVI mode. Name Description Brightness CAL Switch to calibrated position of brightness Man Brightness Manually adjust brightness System Manual Color Coronis 2MP...
Page 105
Standard Display operation Luminance Name Description Target Value Manually adjust the luminance The luminance is indicated in cd/ m² System Manual Color Coronis 2MP...
Page 106
OSD: Auto: The OSD orientation automatically follows the ori- entation of the display Portrait: The OSD is dis- played in portrait orientation Landscape: The OSD is dis- played in landscape orienta- tion Adjustments: Phase System Manual Color Coronis 2MP...
Page 107
Adjust the video sampling fre- quency manually. However, we recommend you use the Automatic Phase function (Autoset menu). Man Phase adj Adjust the video sampling phase manually. However, we recom- mend you use the Automatic Phase function (Autoset menu). System Manual Color Coronis 2MP...
Page 108
LED will turn orange, even if it was switched off by this setting. User Controls Disable the control wheel functions Ambient Light Com- Switch on/off the Ambient Light pensation Compensation (ALC) system System Manual Color Coronis 2MP...
Page 109
Preset. Find next preset Select another Preset from mem- ory that matches the incoming video and sync signals. The num- ber displayed in the OSD is the number of the actual Preset's memory location. System Manual Color Coronis 2MP...
Page 110
The name of the current memory Preset Hor Frequency The currently measured horizontal sync frequency Vert Frequency The currently measured vertical sync frequency Resolution Displays the actual video signal resolution * These functions are not available in DVI mode. System Manual Color Coronis 2MP...
The functions described in this chapter are intended for trained service staff only! Improper use of these functions may disorder the display. BARCO cannot be held responsible for the results or damage caused by improper use of these functions. About the Advanced functions The advanced functions are extensions of the OSD menus.
Low Pass Filter This function is not available in DVI mode The display electronics provide 4 different low-pass System Manual Color Coronis 2MP...
Page 113
Select a different filter in case the image contains high- frequent noise or distortion. Select the filter that gives the best result. Readjustment of sample phase is necessary after selection of a different filter. System Manual Color Coronis 2MP...
Native If you select Native, a linear LUT will be selected Test This selection is meant for internal test purposes. It should not be selected for normal operation. System Manual Color Coronis 2MP...
Page 115
To change the Input Mode setting, click the control wheel. Turn the wheel to select Standard or Extended input mode. Then click the wheel again to enter the selected submenu. The following input mode settings can be selected: System Manual Color Coronis 2MP...
Page 116
RGB sub- pixels of the panel equally. R->Y The Red video signal from the imaging board is used as lumi- nance value to drive the RGB sub- pixels of the panel equally. System Manual Color Coronis 2MP...
Page 117
The RGB video signals from the imaging board are calculated and transformed into a single lumi- nance value according to the for- mula 0.3B + 0.59G + 0.11R. This single luminance signal drives the RGB sub-pixels of the panel equally. System Manual Color Coronis 2MP...
Advanced functions in the Presets menu Clear user Presets Click the control wheel if you wish to reset all the settings of all user Presets. In the menu that appears next, click on Proceed to reset the settings. System Manual Color Coronis 2MP...
The version of the internal run code CPLD Code Version The version of the internal CPLD code FPGA Version The version of the internal FPGA code Mezzanine Version The version of the internal Mezza- nine circuit code System Manual Color Coronis 2MP...
Page 120
Backlight Runtime Indicates the time the backlight has been on since the last time it was switched off (e.g., in stand- by). This counter stops after 1092 minutes. System Manual Color Coronis 2MP...
Page 122
Cleaning (This page intentionally left blank.) System Manual Color Coronis 2MP...
Page 123
A dust remover is composed of a blend of compressed liquid gases functioning as propellant. They provide a jet of dry inert gas that acts like compressed air for a quick and safe removal of dust System Manual Color Coronis 2MP...
Page 124
Repeat with water only and wipe dry with a dry cloth. • The cabinet has been tested for resistance to the following products: Cidex, Betadine, Alcohol (Isopropyl and Ethyl), Ammonia-based cleaners (Windex) and Aquasonic Gel. System Manual Color Coronis 2MP...
If one display from a multi-head system exhibits problems, try to eliminate the problem by switching video cables or power supplies. In that way you can find out if the problem resides in the display or not. System Manual Color Coronis 2MP...
Image contains miss- • A number of missing pixels ing pixels may be normal. Please check the Technical Specifications in this manual to find out the maximum allowed number of missing pixels System Manual Color Coronis 2MP...
Page 129
• Switch the “Scaling” function (Geometry menu) in the display OSD to “None” or “Best Fit” The image on the • Select another resolution in screen is rotated 90° the Windows “Display Properties” control panel System Manual Color Coronis 2MP...
Page 130
On a dual-head sys- • Switch the video cables at the tem, the images on display controller or at the the left and right dis- display video inputs play seem to be switched System Manual Color Coronis 2MP...
To set the resolution of the second display attached to the BarcoMed Display Controller you are working with, go back to the “Settings” tab of the “Display Properties Control Panel”. Attach the second display by right System Manual Color Coronis 2MP...
Page 132
“Attached”. Now repeat steps 4–7 above for this display. Figure 39 Note: The system shown in figure 39 above is a dual- head, single BarcoMed 2MP2CF-3D Display Controller. Your system may look different. System Manual Color Coronis 2MP...
Color Coronis Software CD and double click on the file: “Setup.exe” to start the wizard. The wizard will begin by displaying the screen shown in figure 40 on page 134. System Manual Color Coronis 2MP...
Page 134
3. To update the driver, clear the checkbox next to “DPMS Screen Saver” (Figure 3) and click “Install”. Figure 41 4. Please turn to Step 6 on page 50 and following the instructions in the section titled “Driver System Manual Color Coronis 2MP...
2. The BarcoMed Product Installation Wizard will display its welcome screen. 3. Make certain that the checkbox next to the driver is checked and that all other checkboxes are unchecked (see figure 42 on page 136). Click “Install” to continue. System Manual Color Coronis 2MP...
Page 136
Re-installation or updates Figure 42 4. Click “Next”. 5. On the next screen (figure 43), check the checkbox next to “Uninstall this device” and click “Next” to continue. Figure 43 6. Click “Next”. System Manual Color Coronis 2MP...
Page 137
Re-installation or updates 7. Click “Reboot”, next click “Finish” and then click “Yes” when Windows prompts you to restart your system in order for the system changes to take effect. System Manual Color Coronis 2MP...
Page 138
Re-installation or updates System Manual Color Coronis 2MP...
Push / turn control wheel for stand-by switching and OSD controls Input connectors DVI single link, D-Sub15 pin, BNC (monochrome only) Signal systems DVI Digital, RGB Analog DVI compliance Complying to DVI Rev 1.0 specifications System Manual Color Coronis 2MP...
Page 142
In perpendicular vertical posi- tion, highest position, tilt = 0°, swivel = 0°: 385 x 585 x 250 mm Net weight 13.9 kg Operating Temperature 0°C to 40°C, 15°C to 35°C within specs Storage Temperature -20°C to 60°C System Manual Color Coronis 2MP...
Page 143
Technical specifications Item Specification Humidity 8% - 80% (non-condensing) for operation 5% - 95% (non-condensing) for storage Altitude 7500 m storage 3000 m operation System Manual Color Coronis 2MP...
DVI connector: Signal Signal TMDS DATA 2- +5V POWER TMDS DATA 2+ HOT PLUG DETECT TMDS DATA 0- TMDS DATA 0+ DDC CLOCK DDC DATA TMDS DATA 1- TMDS DATA 1+ TMDS CLOCK- TMDS CLOCK+ System Manual Color Coronis 2MP...
Page 145
Connector pin assignments D-Sub 15 connector: Signal Signal Red in DDC 5V IN Green in VGA PRES Blue in DDC SDA HS IN VS IN DDC SCL System Manual Color Coronis 2MP...
This is called a dual head imaging board. It is like two complete imaging boards implemented on one single unit. A dual head board in the computer behaves exactly as if two separate boards were installed. System Manual Color Coronis 2MP...
Page 147
When you make adjustments and save the changes, the current Preset is saved as programmable Preset. If this happens while all programmable Presets are occupied, the oldest programmable Preset is overwritten automatically. System Manual Color Coronis 2MP...
Page 148
Glossary System Manual Color Coronis 2MP...
Warranty Statement System Manual Color Coronis 2MP...
Page 150
Warranty Statement (This page intentionally left blank.) System Manual Color Coronis 2MP...
Page 151
1.4 Replacement parts used shall be new or equivalent to new parts for the revision level of the equipment. The warranty period for the replacement parts will expire at the same moment as the original warranty period of the System Manual Color Coronis 2MP...
Page 152
2.6 Any specific services or procedures, asked for by Customer, related to verification of repaired equipment. System Manual Color Coronis 2MP...
Page 153
BarcoView. Any attempt to do so, voids the warranty. ARTICLE 5: DISCLAIMER OF WARRANTIES Barcoview disclaims all warranties, expressed or implied, including all implied warranties of merchantability and fitness for a particular purpose System Manual Color Coronis 2MP...
Page 154
ARTICLE 8: GENERAL 8.1 Customer acknowledges its understanding that all software and electronic devices, including BarcoView products are subject to possible error, mechanical or electrical failure, and should not be relied upon in System Manual Color Coronis 2MP...
Page 155
8.2 BarcoView shall not be responsible for machine failure and/or its failure to render service or maintenance due to causes beyond its reasonable control. System Manual Color Coronis 2MP...
Page 156
Warranty Statement (This page intentionally left blank.) System Manual Color Coronis 2MP...