Advertisement
Copyright
Copyright © 2003 by PLANET Technology Corp. All rights reserved. No part
of this publication may be reproduced, transmitted, transcribed, stored in a
retrieval system, or translated into any language or computer language, in any
form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual or otherwise, without the prior written permission of PLANET.
PLANET makes no representations or warranties, either expressed or implied,
with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Any software described
in this manual is sold or licensed "as is". Should the programs prove defec-
tive following their purchase, the buyer (and not PLANET, its distributor, or
its dealer) assumes the entire cost of all necessary servicing, repair, and any
incidental or consequential damages resulting from any defect in the software.
Further, PLANET reserves the right to revise this publication and to make
changes from time to time in the contents hereof without obligation to notify
any person of such revision or changes.
All brand and product names mentioned in this manual are trademarks and/or
registered trademarks of their respective holders.
FCC Regulation
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference
and (2) this device must accept any interference received, including interfer-
ence that may cause undesired operation.
Revision
Quick Installation Guide for PLANET 2.4GHz WLAN Booster
Model: WBT-500/1000
Rev: 1.0 (December, 2003)
Part No. EMQ-WBT
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Planet WBT-1000
Summary of Contents for Planet WBT-1000
- Page 1 Copyright Copyright © 2003 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
- Page 2 OUTDOOR INSTALLATION WARNING IMPORTANT SAFETY PRECAUTIONS: LIVES MAY BE AT RISK! Carefully observe these instructions and any special instructions that are included with the equipment you are installing. IMPORTANT: Look over the site before beginning any installation, and anticipate possible hazards, especially these. CONTACTING POWER LINES CAN BE LETHAL.
- Page 3 building protective ground or to one or more approved grounding rods, using 1 OAWG ground wire and corrosion-resistant connectors. • Refer to the National Electrical Code for grounding details. • Lightning arrestors for antenna feed coaxial cables are available from Hyper- Link Technologies, Inc.
-
Page 4: Table Of Contents
Table of Contents Package Content Features Preparations Hardware Installation Troubleshooting... -
Page 5: Package Content
Specifications Booster Operating Frequency 2400 – 2500MHz Operating Mode Bi-directional TDD (Time Division Duplex) WBT-500: 500mW (27dBm) Transmitter Output Power WBT-1000: 1000mW (30dBm) Transmitter Input Power 2dBm – 15dBm Receiver Input Power -16dBm (max.) Receiver Gain 20dB Frequency Response Flatness ±... -
Page 6: Features
• 2400~2500 MHz unlicensed ISM Band • Provides DC Power to the booster without an additional Power cord • Booster has 500/1000mW output power levels • 20dB(WBT-500)/22dB(WBT-1000) receive gain for the booster • Bi-directional TDD technology • Transmitter and receiver LED indicator •... -
Page 7: Hardware Installation
Misc. Loss means loss of connector, adapter and DC injector and NOTE: estimates to be around 2 dB. 4. When the input signal level exceeds the Receiver Input Power of booster, the booster can’t identify the input signal. Under this circumstance, user should lower the input signal level to fit the requirement such as using an attenuation pad or a higher loss cable and vice versa. -
Page 8: Troubleshooting
Troubleshooting If there is no signal output, please check the following item: 1. Check whether the LED indicator on the DC injector is on. If not, it means there is problem with the power component. (1) Check if the power cord is correctly connected with the power adapter and the power outlet. - Page 10 Part No.:EMQ_WBT...
Need help?
Do you have a question about the WBT-1000 and is the answer not in the manual?
Questions and answers