Related Manuals for Patton electronics 1200P
Summary of Contents for Patton electronics 1200P
- Page 1 Doc #: 112001UA Part #: 07M1200P-A MODEM E , RS-232 LIMINATOR 1200P (CTS ME-V.24) NSTALLATION AND PERATIONS ANUAL May 15, 2000 An ISO-9001 Copyright© 2000 Patton Electronics Co., All Rights Reserved Certified Company...
- Page 2 Doc #: 112001UA Part #: 07M1200P-A MODEM E , RS-232 LIMINATOR 1200P (CTS ME-V.24) NSTALLATION AND PERATIONS ANUAL An ISO-9001 Copyright© 2000 Patton Electronics Co., All Rights Reserved Certified Company...
-
Page 3: Radio And Tv Interference
Patton Electronics Co. 1200P NSTALLATION PERATIONS ANUAL 112001UA PROPRIETARY NOTICE The information contained herein is proprietary and confidential to Patton Electronics Co. Any reproduction or redistribution of this publication, in whole or in part, is expressly prohibited unless written authorization is given by Patton Electronics Co. - Page 4 Patton Electronics Co. 1200P NSTALLATION PERATIONS ANUAL 112001UA This Page Left Blank...
-
Page 5: Table Of Contents
Patton Electronics Co. 1200P NSTALLATION PERATIONS ANUAL 112001UA Contents CHAPTER 1 - OPERATION CHAPTER 2 - SETUP AND INSTALLATION Power Connection ..................2-1 Factory Configuration ................... 2-1 Installation....................2-1 CTS Delay (SW2-1,2) .................. 2-2 DSR Control (SW2-3,4) ................2-2 DCD Control (SW2-5,6) ................2-3 Clocking (SW1-1,2,3,4,5) ................ -
Page 6: Chapter 1 - Operation
RS-232 / V.24 terminal to another RS-232 / V.24 terminal without the use of two Modems. The 1200P (CTS ME-V.24) provides sync baud rates up to 76.8Kbps. When the 1200P (CTS ME-V.24) is used with async data, baud rate selection is not required, because the Modem Eliminator is transparent to the data. -
Page 7: Chapter 2 - Setup And Installation
CHAPTER 2 - SETUP AND INSTALLATION Power Connection Before connecting the 1200P (CTS ME-V.24) to an AC power source the top cover must be installed and secured with the supplied screws. The unit is supplied with a 110/220VA voltage switch, turn the switch with a coin or screw driver to the appropriate voltage for your country. -
Page 8: Cts Delay (Sw2-1,2)
Patton Electronics Co. 1200P NSTALLATION PERATIONS ANUAL 112001UA CTS Delay (SW2-1,2) SW2 position 1 selects RTS to CTS delay for the terminal connected to J3. Set SW2 position 1 to ON ON for no delay and OFF OFF for 25ms of delay. SW2 position 2 selects RTS to CTS delay for the terminal connected to J2. -
Page 9: Dcd Control (Sw2-5,6)
Patton Electronics Co. 1200P NSTALLATION PERATIONS ANUAL 112001UA DCD Control (SW2-5,6) SW2 position 5 selects DCD control for the terminal connected to J2. Setting SW2 position 5 to ON ON will select DCD on J2 to switch in responce to RTS from J3 OFF will force DCD on J2 to Active. -
Page 10: Appendix
Patton Electronics Co. 1200P NSTALLATION PERATIONS ANUAL 112001UA Appendix Technical Specifications Applications Power Requirements RS-232 Sync or Async Terminal to 110-120/200-240 VAC, 50 to 60Hz, Terminal interconnection. 0.16/0.08 A, Switch Selectable Capacity Approvals Two RS-232 Terminals MET, c-MET,& CE Data Format Environmental Data Coding: .. - Page 11 Patton Electronics Co. 1200P NSTALLATION PERATIONS ANUAL 112001UA 1200P Signal Routing Diagram Appendix...
- Page 12 7622 Rickenbacker Drive Gaithersburg, MD 20879 Sales: 301 975-1000 Support: 301 975-1007 Web Address: www.patton.com...