Electrical Data - Pump Package Option; Installer-Supplied Components - Trane RTAA-70 Installation & Maintenance Manual

Table 11

Electrical Data - Pump Package Option

Rotated Pump
Unit Size Voltage HP
RTAA 70
460/60 2
460/60 3
460/60 5
RTAA 80
460/60 2
460/60 3
460/60 5
460/60 7 .5
RTAA 90 460/60 3
460/60 5
460/60 7 .5
RTAA 100 460/60 3
460/60 5
460/60 7 .5
RTAA 110 460/60 3
460/60 5
460/60 7 .5
RTAA 125 460/60 3
460/60 5
460/60 7 .5
(1) MOP - Maximum Overcurrent Protection - may be either type breaker (UL/CSA) or with circuit breakers (CSA only). MOP = 225 percent of the largest
compressor RLA plus 100 percent of the second compressor plus the sum of the condenser fans FLAs per NEC 440-22.
(2) MCA - Minimum Circuit Ampacity - 125 percent of largest compressor RLA plus 100 percent of second compressor plus the sum of the condenser
fans FLAs per NEC 440-33.
(3) RECOMMENDED TIME DELAY OR DUAL ELEMENT (RDE) FUSE SIZE: 150 percent of the largest compressor RLA plus 100 percent of the
second compressor RLA and the sum the condenser fan FLAs.
(4) RLA -Rated Load Amps -rated in accordance with UL Standard 465.
(5) Local codes may take precedence.
(6) Control kw includes operational controls only. Does not include heat tapes.
(7) LRA - Locked Rotor Amps -based on full winding start units.
(8) VOLTAGE UTILIZATION RANGE:
Rated Voltage
200/60
230/60
460/60
575/60
400/50
(9) 60 HZ UNITS - A 115/60/1, 15 amp. customer provided power connection is required to power the evaporator heat tape 420 watts
(10) 50 HZ UNITS - A separate 220/50/1 15 amp. customer provided power connection is needed to power evaporator heat tape 420 watts @ 220 volts.
RTAA-SVX01A-EN
Installation — Electrical
Unit Wiring
Pump
FLA MCA (2) MOP (1)
3.1 136 175
4.1 137 175
6.6 139 175
3.1 163 200
4.1 164 225
6.6 166 225
10.3 170 225
4.1 194 250
6.6 196 250
10.3 200 250
4.1 218 300
6.6 221 300
10.3 224 300
4.1 239 300
6.6 242 300
10.3 246 300
4.1 256 350
6.6 259 350
10.3 263 350
Utilization Range
180-220
208-254
414-506
516-633
340-460

Installer-Supplied Components

All wiring must comply with local codes and the National Electrical Code. The
installing (or electrical) contractor must provide and install the system inter-
connecting wiring, as well as the power supply wiring. It must be properly
sized and equipped with the appropriate fused-disconnect switches. The type
and installation location(s) of the fused-disconnects must comply with all
applicable codes.
The installer must provide the following components if not ordered with the
unit:
• Power supply wiring (in conduit) for all field-wired connections.
• All control (interconnecting) wiring (in conduit) for field supplied devices.
• Fused-disconnect switches.
Remote Evaporator Only:
• Control wiring between the outdoor unit and the evaporator terminal box.
Motor Data
Rec Time
Delay or Comp(Ea)
RDE (3) Qty RLA (4)
150 2 50/50
150 2 50/50
175 2 50/50
200 2 62/62
200 2 62/62
200 2 62/62
200 2 62/62
225 2 84/62
225 2 84/62
225 2 84/62
250 2 84/84
250 2 84/84
350 2 84/84
300 2 101/84
300 2 101/84
300 2 101/84
300 2 101/101
300 2 101/101
300 2 101/101
Fans
(Ea)
LRA (7) Qty KW FLA
330/330 8 1.0 2.5
330/330 8 1.0 2.5
330/330 8 1.0 2.5
380/380 8 1.0 2.5
380/380 8 1.0 2.5
380/380 8 1.0 2.5
380/380 8 1.0 2.5
410/380 9 1.0 2.5
410/380 9 1.0 2.5
410/380 9 1.0 2.5
410/410 10 1.0 2.5
410/410 10 1.0 2.5
410/410 10 1.0 2.5
522/410 10 1.0 2.5
522/410 10 1.0 2.5
522/410 10 1.0 2.5
522/522 10 1.0 2.5
522/522 10 1.0 2.5
522/522 10 1.0 2.5
Control
KW (6)
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
0.75
51