Access Code Programming; Access Codes; Master Code] (When Disarmed); User Code Attributes - DSC Impassa User Manual

15. Access Code Programming

In addition to the master code, you can program up to 16 additional user access codes.
To program User Access Codes:
1. Disarm your system, if it is armed/set.
2. Press [ ][5][Master Access Code (i.e., 4- or 6-digit code)]; the armed ( ) indicator will turn on.
,
3. Enter the 2-digit number to be programmed. This number is used to identify the User Access Code
being entered (e.g., 06 for User Access Code 6; enter 40 for the master access code), or press the
scroll [<][>] buttons to find the specific code and press [
4. Enter the new 4-digit or 6-digit access code. When programming is complete, enter another 2-digit
code to program or press [#] to exit.
The access codes have programmable attributes which allow zone bypassing, duress, supervisor,
remote access, or one-time use activation.
On WT5500P keypads, you will be prompted to swipe a proximity tag once the last character of the
access code is entered. To delete proximity tags, the associated user access code must be deleted as
described, then re-programmed if required.
NOTE: If wireless keys have been programmed, wireless key #1 will log as User Access Code #1 (if
that access code has been programmed). User Access Codes 1-16 will correspond to wireless keys or
proximity tags 1-16.
NOTE: When using 6-digit access codes, the minimum number of variations of access codes is 58,823.
15.1 Access Codes — [
The [ ][5] User's Programming command is used to program additional access codes (see Access
,
Code Programming).
User Codes - User codes 1-16 are available for the system.
Master Code (Access Code 40)
ble Attributes list below except for Duress (2) and One-Time Use (8) and is required to program all
supervisor code attributes.
Supervisor Codes
ming or [ ][6] User Function sections. However, these codes can only program additional codes
,
which have equal or lesser attributes. Once programmed, the supervisor codes receive the master
code's attributes. These attributes are changeable. Any user code can be made a supervisor code by
enabling User Code Attribute 1 (please see below for details).
- Duress codes are standard user codes that will transmit the Duress Alarm Reporting
Duress Codes
Code whenever the code is entered to perform any function on the system. Any user code can be
made a duress code by enabling User Code Attribute 2 (see below for details).
One-Time Use Code - This code permits temporary access to the system for a 24-hour time period. During
the 24hr period, the temporary user may disarm the system once. There is no restriction on the number of
times the temporary user may arm/set the system during the time period.
NOTE: Duress codes are not valid when entering [
NOTE: Access codes cannot be programmed as a duplicate or as a Code +/- 1.

15.2 User Code Attributes

The default attributes of a new code will be the attributes of the code used to enter [
a new code or an existing code being programmed.
System Master (Code 40) has Attribute 3 on by default.
NOTE: These attributes are not changeable.

15.3 Inherent Attributes (all codes except installer)

Arm (Set) / Disarm (Unset)
Command Outputs ([
code is valid for performing the [
Programmable Attributes ([
To program an access code attribute enter [
access code (e.g., 2-digit number 01-16) you want to program. Press [
,

][5][Master Code] (when disarmed)

- The master code has all of the attributes listed in the Programma-
- These codes are always valid when entering the [
- Any access code will be valid for arming and disarming the system.
, ,
][7][1] and [ ][7][2])
][7][1-2][Access Code] functions on the system.
,
,
][5][Master/Supervisor Code][9][Code])
] to select.
,
][5], [ ][6] or [
, ,
- If these outputs require access code entry, any access
][5][Master/Supervisor Code][9] then [<][>] scroll to the
,
9
][5] User Code Program-
,
][8] sections.
,
,
] to select the access code.
,
][5] whether it is