Toa Q-CV24VP-3 Operating Instructions Manual
Toa Q-CV24VP-3 Operating Instructions Manual

Toa Q-CV24VP-3 Operating Instructions Manual

Vandal proof dome camera
Hide thumbs Also See for Q-CV24VP-3:

Advertisement

Quick Links

VANDAL PROOF
DOME CAMERA
Thank you for purchasing Vandal Proof Dome Camera. Please carefully follow the instructions in this
manual to ensure long, trouble-free use of your equipment.
OPERATING INSTRUCTIONS
Q-CV24VP-3
Q-CV24VP-4

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Q-CV24VP-3 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Toa Q-CV24VP-3

  • Page 1 OPERATING INSTRUCTIONS VANDAL PROOF Q-CV24VP-3 DOME CAMERA Q-CV24VP-4 Thank you for purchasing Vandal Proof Dome Camera. Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.
  • Page 2: Table Of Contents

    TABLE OF CONTENTS 1. SAFETY PRECAUTIONS ................3 2. HANDLING PRECAUTIONS ................4 3. UNPACKING ....................... 4 4. DESCRIPTION & SPECIFICATIONS ............4 5. NOMENCLATURE ..................... 5 6. COVER REMOVAL & REPLACEMENT ............. 6 7. INSTALLATION 7.1. Connecting Low Voltage Power & Video Signal ..........6 7.1.1.
  • Page 3: Safety Precautions

    • Should the following irregularity be found during use, immediately switch off the power, disconnect the power supply plug from the AC outlet and contact your nearest TOA dealer. Make no further attempt to operate the unit in this condition as this may cause fire or electric shock.
  • Page 4: Handling Precautions

    Modifications Any modifications made to this device that are not approved by TOA Corporation may void the authority granted to the user by the FCC to operate this equipment.
  • Page 5: Nomenclature

    5. NOMENCLATURE [Bottom view] [Top view] [Side view] [Side view of the camera with a dome cover] (1) Monitor output terminal (7) Video output cable (RCA pin jack) (8) Zoom ring fixing screw (2) Vari-focal lens (9) Focus ring fixing screw (3) Mode setting switch (10) Focus ring (4) Iris control...
  • Page 6: Cover Removal & Replacement

    6. COVER REMOVAL & REPLACEMENT 1. Using the special Allen wrench provided, remove the 4 tamper resistant screws located on the cover. The screws are captive and will remain with the cover. Refer to Figure 1. 2. Lift the housing off the base to make required camera adjustments. 3.
  • Page 7: Connecting Low Voltage Power

    7.1.1. Connecting Low Voltage Power Connect the line and neutral wires. 1. 12 VDC Applications: Connect the 12 volt plus wire to the red lead. Connect the neutral/ common wire to the black lead. 2. 24 VAC Applications: Camera operation is not affected by the polarity of the 24 VAC wires. However, in multiple camera systems, consistent wiring configurations will help maintain roll-free switching.
  • Page 8: Adjustment

    8. ADJUSTMENT Note Do not touch any component other than the pc board, the lens or the DIP SW, as this will damage the camera. 1. Switch on the camera power after completing camera connections.Power is supplied to the camera. 2.
  • Page 9: About The Mode Setting Switch

    9. ABOUT THE MODE SETTING SWITCH Note Do not touch any component other than the pc board, the lens or the DIP SW, as this will damage the camera. Set the Mode setting switch for the best possible picture reproduction depending on installation conditions. Mode setting switch (Factory-preset setting) OFF ON...
  • Page 10: Specifications

    10. SPECIFICATIONS Q-CV24VP-3 Q-CV24VP-4 Model No. 24 V AC, 50/60 Hz, or 12 V DC Power Source Power Consumption 1/4 type IT-CCD Image Device 768 (H) x 494 (V), 380,000 pixels Number of Effective Pixels 2:1 interlace Scanning System Horizontal: 15.734 kHz, Vertical: 59.94 Hz (V)
  • Page 12 Printed in Japan 6 3 3 - 1 2 - 0 3 2 - 2 0...

This manual is also suitable for:

Q-cv24vp-4

Table of Contents