PT10-PRV 2 X 1 Preview Switcher System C a m e ra C o n t r o l S y s t e m s...
Page 2
This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party.
Table of Contents Table of Contents PT10-PRV 2 x 1 Preview Switcher System Package ..........1 PT10-PRV System Components..................1 2 x 1 Video Preview Switcher Configuration ..............2 Installation and Wiring .....................3 Wiring Information for the AV2SM..................3 Using the CC-REL connection cable..................3 Operation...........................
Page 4
Table of Contents PT10-PRV 2 x 1 Preview Switcher System...
PT10-PRV 2 x 1 Preview Switcher System Package PT10-PRV 2 x 1 Preview Switcher System Package The AMX Preview Switcher System uses the AXP-PLV PosiTrack Pilot Video Panel Camera Controller in conjunction with the AXB-REL8 Relay Controller and the AV2SM 2 x 1 A/V Switcher.
PT10-PRV 2 x 1 Preview Switcher System Package 2 x 1 Video Preview Switcher Configuration The following example (FIG. 1) adds a 2 x 1 video preview switcher to any of the other AMX Camera Control Systems. Video Feed 1 (to VIDEO-INPUT A on rear)
Installation and Wiring Installation and Wiring This section covers the steps necessary to connect and operate a PT10-PRV 2 x 1 Video Preview System. Before continuing, verify that you have received the correct components for your package. Refer to the PT10-PRV System Components section on page 1 for more information.
Recommended Lenses for Sony PosiTrack Systems For optimal performance AMX recommends the use of direct analog voltage controllable lenses. These lenses allow the PT10 or PT30 full control of lens functions. If direct analog voltage control lenses are not available the PT10 and PT30 can support lenses controlled via the camera’s RS232 port such as the double hot shoe type.
AXB-PT10's are factory set to device 90 which corresponds to camera 1 on the controller. Additional PT10's should be set sequentially. AXlink Device Camera Number Use the DIPSwitch.exe program to reference the correct switch settings. Power must be cycled for changes to take effect. PT10-PRV 2 X 1 Preview Switcher System...
• Upgrade to Master Axcess code version 1.56 or later with enhanced Sony communication reliability. • Verify AMX devices are set to 9600 baud. 1. On the PT10 switch S2 should have all switches up (on) except switch 7 which should be down (off).
Page 12
Troubleshooting PT10-PRV 2 X 1 Preview Switcher System...
Professional Group. Staffed with full-time agents, the center is the focal point of contact for any Broadcast and Professional Group inquiry. The BIC is designed to provide general information, including product specifications, literature and list prices to inquiring callers. Tel: 1-800-686-SONY Email: http://bpgprod.sel.sony.com/cic.htm PT10-PRV 2 X 1 Preview Switcher System...
Page 14
Sony Technical Support PT10-PRV 2 X 1 Preview Switcher System...
Page 17
Sony Technical Support PT10-PRV 2 X 1 Preview Switcher System...
Page 18
AMX reserves the right to alter specifications without notice at any time. brussels • dallas • los angeles • mexico city • philadelphia • shanghai • singapore • tampa • toronto* • york 3000 research drive, richardson, TX 75082 USA • 469.624.8000 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993...
Need help?
Do you have a question about the PT10-PRV 2 X 1 and is the answer not in the manual?
Questions and answers