Related Manuals for Miele SE 213
Summary of Contents for Miele SE 213
-
Page 1: Operating Instructions
Operating instructions for hob control units SE 213, SE 233 Q\@ä} It is to read these operating instructions before installing or using the machine, to avoid the risk of accident, or damage to the machine. M.-Nr. 04 392 021... - Page 2 Contents ......... 3 .
- Page 3 Description of the appliance Hob lock Cooking zone control: front left Cooking zone control: back left Cooking zone control: back right Cooking zone control: front right When the control unit has been built in the data plate can not be seen. A further data plate is supplied with this appliance.
- Page 4 Caring for the environment Old machines contain materials which can be reclaimed or recycled. Please The transport and protective packing contact your dealer, your local waste has been selected from materials collection centre or scrap merchant which are environmentally friendly for about potential recycling schemes.
- Page 5 The appliance in combination with qualified and competent persons to en- a Miele hob / cooktop is intended sure safety. Repairs and other work by for domestic use to cook food, and in unqualified persons could be dan- particular to boil, simmer, stew, fry and gerous.
- Page 6 The appliance is only completely In areas which may be subject to isolated from the electricity supply infestation by cockroaches or other when: vermin, pay particular attention to keeping the appliance and its sur- – it is switched off at the wall socket roundings in a clean condition at all –...
- Page 7 Safety feature Use a coin to turn the slit to the "I" The hob lock can be set so that the setting. cooking zones cannot be turned on. The cooking zones can be used again. Use a coin to turn the slit to the "0" setting.
- Page 8 Cleaning and care Never use cleaners containing Use a mild cleaning agent or a dash of sand, soda or scouring agents, detergent in hot water. Wipe dry with a These will leave scratches. soft cloth. Use a non-scouring stainless steel cleaner.
- Page 9 – your Miele Dealer are shown on the data plate. Please also quote the model and serial – the nearest Miele Service Depart- number of your hob. ment, (see address on the back page).
- Page 10 If the connection requires a different cable, the Miele Service dept must Connection of this appliance should be be consulted. made via a suitable isolator which com-...
- Page 11 The fuse rating is 32 amps. The control unit is fitted with an approx. 1.8 metres long cable. If the connection requires a different cable, the Miele Service dept must be consulted. See the data plate for the maximum rated load.
- Page 12 @ä @ä Electrical connection The wire which is coloured green and Electrical connection of the yellow must be connected to the termi- appliance should be undertaken by nal in the plug which is marked with the a qualified electrician in strict ac- letter E or by the earth symbol z or cordance with national and local coloured green or green and yellow.
- Page 13 KM 243 KSE 202-1 KM 247 The fuse rating is 25 amps for SE 213 KM 251 KSE 204-1 and SE 233 (max. rated load 8400 W) with hob. ä...
- Page 14 Installation Before building in the control unit pull the control knobs out of the openings in the facia. Draw out the control unit from the re- taining plate. The control unit must be separated by a removable shelf from the rest of the space in the base unit, to make it inaccessible.
- Page 15 The plugs on the control unit / hob and the sockets on the hob elec- tronic control are coded with the same colour for matching. Fit the plugs into the sockets. Insert the knobs for the control unit into the control facia. Put the hob electronic control into the control unit.
- Page 16 Fit the hob plugs into the sockets. When pushing the control unit into Feed the connection cable without a place, ensure that no connecting plug through a suitable hole in the cables are crushed or caught. base unit. Connect to the electricity supply with an isolator which com- The mains cable must not come into plies with national and local regula-...
- Page 17 For safety reasons, a protective shelf must be installed as shown to ensure that inadvertant contact with the hot underside is prevented. The distance between the lower edge of the worktop and the upper edge of the removable barrier must be a minimum of 125 mm.
- Page 18 This unit is obtainable from your Miele dealer, or the Miele Spare Parts dept, and consists of a 3.5 metre long con- necting cable and an additional con-...
- Page 19 connection cabling (in ducting behind plaster) connection cabling (in ducting behind the wall units) The control unit must be built in within view of the hob.
- Page 20 The cable conduit must meet statu- Disconnect the mains electricity tory electrical requirements and supply to the appliance. have an inner diameter of at least 23 mm for data cable und 29 mm Install the hob. for power cable. Starting from the wall unit push the The conduit length should be suffi- cables into the ducting.
- Page 21 Screw the additional connector box to the protective shelf underneath the hob. In doing so make sure the connection protective shelf above box is as close to the back wall of control unit the unit as possible. wall unit facia cut-out cable in ducting The ducting for the electric cabling must continue right up to the addi-...
- Page 22 Before building in the control unit pull the control knobs out of the openings in the facia. Draw out the control unit from the re- taining plate. Set the control unit retaining plate into the furniture unit cut-out. Put the hob electronic control into Fix the retaining plate to the side the control unit.
- Page 23 Pull the connection cables as far as The plugs on the control unit / the possible in the direction of the con- connection cable and the sockets trol unit, and roll up if possible. on the hob electronic control are coded with the same colour for matching.
- Page 24 Feed the connection cable through a suitable hole in the base unit. Con- nect to the electricity supply with an isolator which complies with national and local regulations. Use the cable clamp to secure the cables together. When pushing the control unit into place, ensure that no connecting cables are crushed or caught.
- Page 25 For safety reasons, a protective shelf must be installed as shown to ensure that inadvertant contact with the hot underside is prevented. The distance between the lower edge of the worktop and the upper edge of the protective shelf must be a minimum of 125 mm.
- Page 28 Alterations rights reserved / 22 GB / IRL / AUS / NZ / ZA – 1597 M.-Nr. 04 392 021 This paper consists of cellulose which has been bleached without the use of chlorine.