Roland FP-7F Implementation Manual page 30

● 0175: Telephone
No Parameter Value
1 Voice Quality #1 0-15
2 Treble 0-30
3 Balance #2 0-100
4 Level 0-127
● 0156: Gate Reverb
This is a special type of reverb in which the reverberant sound is cut off before
its natural length.
No Parameter Value
1 Type #1 0-3
2 Pre Delay 0-125
3 Gate Time 0-99
4 Low Gain 0-30
5 High Gain 0-30
6 Balance #2 0-100
7 Level 0-127
● 0200: Overdrive→Chorus
This effect connects an overdrive and a chorus in series.
No Parameter Value
1 Overdrive Drive 0-127
2 Overdrive Pan 0-127
3 Chorus Pre Delay 0-125
4 Chorus Rate Mode 0-1
5 Chorus Rate #1 1-127
6 Chorus Rate 0-21
7 Chorus Depth 0-127
8 Chorus Balance #2 0-100
9 Level 0-127
● 0201: Overdrive→Flanger
This effect connects an overdrive and a flanger in series.
No Parameter Value
1 Overdrive Drive 0-127
2 Overdrive Pan 0-127
3 Flanger Pre Delay 0-125
Description
Audio quality of the telephone
0-15
voice
-15 - +15 dB Bandwidth of the telephone voice
D100:0 - Volume balance between the direct
D0:100W sound (D) and the effect sound (W)
0-127 Output level
Description
Type of reverb
Normal: conventional gated
Normal, reverb
Reverse, Reverse: backwards reverb
Sweep1, Sweep1: the reverberant sound
Sweep2 moves from right to left
Sweep2: the reverberant sound
moves from left to right
Adjusts the delay time from the
0.0-100.0 ms direct sound until the reverb
sound is heard.
Adjusts the time from when the
5-500 ms
reverb is heard until it disappears.
-15 - +15 dB Gain of the low range
-15 - +15 dB Gain of the high range
Volume balance between the direct
D100:0W -
sound (D) and the reverb sound
D0:100W
(W)
0-127 Output Level
Description
Degree of distortion Also changes
0-127
the volume.
Stereo location of the overdrive
L64 - 63R
sound
Adjusts the delay time from the
0.0-100.0 ms direct sound until the chorus
sound is heard.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
0.05 - 10.00 Hz Frequency of modulation (Hz)
note Frequency of modulation (note)
0-127 Depth of modulation
Adjusts the volume balance
between the sound that is sent
D100:0W -
through the chorus (W) and the
D0:100W
sound that is not sent through the
chorus (D).
0-127 Output Level
Description
Degree of distortion Also changes
0-127
the volume.
Stereo location of the overdrive
L64 - 63R
sound
Adjusts the delay time from when
0.0-100.0 ms the direct sound begins until the
flanger sound is heard.
4 Flanger Rate Mode 0-1
5 Flanger Rate #1 1-127
6 Flanger Rate 0-21
7 Flanger Depth 0-127
8 Flanger Feedback 0-98
9 Flanger Balance #2 0-100
10 Level 0-127
● 0202: Overdrive→Delay
This effect connects an overdrive and a delay in series.
No Parameter Value
1 Overdrive Drive #1 0-127
2 Overdrive Pan 0-127
3 Delay Mode 0-1
4 Delay Time 0-127
5 Delay Time 0-21
6 Delay Feedback 49-89
7 Delay HF Damp 0-17
8 Delay Balance #2 0-100
9 Level 0-127
● 0203: Distortion→Chorus
The parameters are essentially the same as in "Overdrive→Chorus," with the
exception of the
following two.
Overdrive Drive→Distortion Drive
Overdrive Pan→Distortion Pan
● 0204: Distortion→Flanger
The parameters are essentially the same as in "Overdrive→Flanger," with the
exception of the
following two.
Overdrive Drive→Distortion Drive
Overdrive Pan→Distortion Pan
● 0205: Distortion→Delay
The parameters are essentially the same as in "Overdrive→Delay," with the
exception of the
following two.
Overdrive Drive→Distortion Drive
Overdrive Pan→Distortion Pan
30
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
0.05-10.00 Hz Frequency of modulation (Hz)
note Frequency of modulation (note)
0-127 Depth of modulation
Adjusts the proportion of the
flanger sound that is fed back into
-98 - +98%
the effect. Negative (-) settings will
invert the phase.
Adjusts the volume balance
between the sound that is sent
D100:0W -
through the flanger (W) and the
D0:100W
sound that is not sent through the
flanger (D).
0-127 Output Level
Description
Degree of distortion Also changes
0-127
the volume.
Stereo location of the overdrive
L64 - 63R
sound
When this is set to "note," the
ms, note effect is synchronized with the
tempo.
Adjusts the delay time from the
0 - 2540 ms direct sound until the delay sound
is heard. (Hz)
Adjusts the delay time from the
note direct sound until the delay sound
is heard. (note)
Adjusts the proportion of the delay
0 - +80% sound that is fed back into the
effect.
Adjusts the frequency above which
sound fed back to the effect will be
200-8000 Hz,
cut. If you do not want to cut the
Bypass
high frequencies, set this
parameter to Bypass.
Adjusts the volume balance
between the sound that is sent
D100:0W -
through the delay (W) and the
D0:100W
sound that is not sent through the
delay (D).
0-127 Output Level