Roland FP-7F Implementation Manual page 26

● 012d: Rotary2
This type provides modified response for the rotary speaker, with the low end
boosted further.
This effect is a descendant of the Roland VK Series' built-in rotary speaker.
No Parameter Value
1 Speed #1 0-1
2 Brake #2 0-1
3 Woofer Slow Speed 1-127
4 Woofer Fast Speed 1-127
5 Woofer Trans Up 0-127
6 Woofer Trans Down 0-127
7 Woofer Level 0-127
8 Tweeter Slow Speed 1-127
9 Tweeter Fast Speed 1-127
10 Tweeter Trans Up 0-127
11 Tweeter Trans Down 0-127
12 Tweeter Level 0-127
13 Spread 0-10
14 Low Gain 0-30
15 High Gain 0-30
16 Level 0-127
● 0300: Rotary Multi
This is an effect combining the VK series internal effect with an organ effect
with the same features.
It comprises vibrato/chorus, overdrive, and rotary effects.
No Parameter Value
1 Vib/Cho Switch 0-1
2 Vib/Cho Type 0-5
3 Vib/Cho Vintage 0-2
4 Vib/Cho Level 0-127
5 OD Switch 0-1
6 OD Drive #2 0-127
7 OD Level 0-127
8 Rotary Switch 0-1
9 Rotary Speed #1 0-1
10 R-Wf Slow Sp 1-127
11 R-Wf Fast Sp 1-127
Description
Rotational speed of the rotating
Slow, Fast
speaker
Switches the rotation of the rotary
speaker. When this is turned on, the
Off, On rotation will gradually stop. When it
is turned off, the rotation will
gradually resume.
Low-speed rotation speed of the
0.05-10.00 Hz
woofer
High-speed rotation speed of the
0.05-10.00 Hz
woofer
Adjusts the rate at which the woofer
rotation speeds up when the
0-127
rotation is switched from Slow to
Fast.
Adjusts the rate at which the woofer
rotation speeds up when the
0-127
rotation is switched from Fast to
Slow.
0-127 Volume of the woofer
0.05-10.00 Hz
Settings of the tweeter The
0.05-10.00 Hz
parameters are the same as for the
0-127
woofer.
0-127
0-127
Sets the rotary speaker stereo
image.
0-10
The higher the value set, the wider
the sound is spread out.
-15 - +15 dB Gain of the low range
-15 - +15 dB Gain of the high range
0-127 Output Level
Description
Switches the vibrato and chorus
Off, On
effects
Vibrato and chorus effect types
V-1, V-2, V-3: Adds a wavering
(vibrato) that is created by
changes in the pitch.
V-1, V-2, V-3, The effect deepens as the value is
C-1, C-2, C-3 increased
C-1, C-2, C-3: Adds a fullness and
breadth (chorus) to the sound.The
effect deepens as the value is
increased.
This reproduces the subtle
differences in the vibrato and
'50, '60, '70
chorus effects in organs built in
different years.
0-127 Vibrato/chorus effect volume
Off, On Switches the overdrive effect
0-127 Amount of distortion
0-127 Overdrive effect volume
Off, On Switches the rotary effect
Low- and high-frequency rotation
Slow, Fast speeds (Rate) Slow: (Slow Rate)
Fast: (Fast Rate)
Rate with low-frequency rotor set to
0.05-10.00 Hz
Slow rate
Rate with low-frequency rotor set to
0.05-10.00 Hz
Fast rate
12 R-Wf Accel 0-15
13 R-Wf Level 0-127
14 R-Tw Slow Sp 1-127
15 R-Tw Fast Sp 1-127
16 R-Tw Accel 0-15
17 R-Tw Level 0-127
18 Rotary Separat 0-127
19 Rotary Level 0-127
● 015b: Stereo Delay1
This is a stereo delay.
No Parameter Value
1 Delay Left Mode 0-1
2 Delay Left 0-127
3 Delay Left 0-21
4 Delay Right Mode 0-1
5 Delay Right 0-127
6 Delay Right 0-21
7 Phase Left 0-1
8 Phase Right 0-1
9 Feedback Mode 0-1
10 Feedback #1 49-89
11 HF Damp 0-17
12 Low Gain 0-30
13 High Gain 0-30
14 Balance #2 0-100
15 Level 0-127
26
Speed at which the low-frequency
0-15 rotor's rotation rate changes when
the rotation speed is switched
0-127 Low-frequency rotor volume
0.05-10.00 Hz
High-frequency rotor setting This
parameter is the same as that for
0.05-10.00 Hz
the low-frequency rotor.
0-15
0-127
0-127 Amount of breadth in the sound
0-127 Output volume
Description
When this is set to "note," the
ms, note effect is synchronized with the
tempo.
Adjusts the time until the delay
0-1270 ms
sound is heard. (Hz)
Adjusts the time until the delay
note
sound is heard. (note)
When this is set to "note," the
ms, note effect is synchronized with the
tempo.
Adjusts the time until the delay
0-1270 ms
sound is heard. (Hz)
Adjusts the time until the delay
note
sound is heard. (note)
Normal,
Phase of the delay sound
Inverse
Selects the way in which delay
Normal, Cross sound is fed back into the effect.
(See the figures above.)
Adjusts the amount of the delay
0 - +80% sound that's fed back into the
effect.
Adjusts the frequency above which
sound fed back to the effect is
200-8000 Hz,
filtered out. If you don't want to
Bypass
filter out any high frequencies, set
this parameter to Bypass.
-15 - +15 dB Gain of the low frequency range
-15 - +15 dB Gain of the high frequency range
D100:0W - Volume balance between the direct
D0:100W sound (D) and the delay sound (W)
0-127 Output level