Roland FP-7F Implementation Manual page 22

● 0127: 3D Flanger
This applies a 3D effect to the flanger sound. The flanger sound will be
positioned 90 degrees left and 90 degrees right.
No Parameter Value
1 Filter Type 0-2
2 Cutoff Freq 0-16
3 Pre Delay 0-125
4 Rate Mode 0-1
5 Rate #1 1-127
6 Rate 0-21
7 Depth #2 0-127
8 Phase 0-90
9 Feedback 0-98
10 Output Mode 0-1
11 Low Gain 0-30
12 High Gain 0-30
13 Balance 0-100
14 Level 0-127
● 0128: 2Band Flanger
A flanger that lets you apply an effect independently to the low-frequency and
high-frequency ranges.
No Parameter Value
1 Split Freq 0-16
2 Low Pre Delay 0-125
3 Low Rate Mode 0-1
4 Low Rate #1 1-127
5 Low Rate 0-21
6 Low Depth 0-127
7 Low Phase 0-90
8 Low Feedback 0-98
9 High Pre Delay 0-125
10 High Rate Mode 0-1
Description
Type of filter
Off: No filter is used
Lpf: Cuts the frequency range
Off, Lpf, Hpf
above the Cutoff Freq
Hpf: Cuts the frequency range
below the Cutoff Freq
200-8000 Hz Basic frequency of the filter
Adjusts the delay time from when
0.0-100.0 ms the direct sound begins until the
flanger sound is heard.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
0.05-10.00 Hz Frequency of modulation (Hz)
note Frequency of modulation (note)
0-127 Depth of modulation
0-180 deg Spatial spread of the sound
Adjusts the proportion of the
flanger sound that is fed back into
-98.98 the effect.
Negative (-) settings will invert the
phase.
Adjusts the method that will be
used to hear the sound that is
output to the OUTPUT jacks. The
Speaker,
optimal 3D effect will be achieved
Phones
if you select Speaker when using
speakers, or Phones when
using headphones.
-15 - +15 dB Gain of the low range
-15 - +15 dB Gain of the high range
Volume balance between the direct
D100:0 -
sound (D) and the flanger sound
WD0:100W
(W)
0-127 Output Level
Description
Frequency at which the low and
200-8000 Hz
high ranges will be divided
Delay time from when the original
0.0-100.0 ms sound is heard to when the low-
range flanger sound is heard
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
Rate at which the low-range flanger
0.05-10.00 Hz
sound is modulated (Hz)
Rate at which the low-range flanger
note
sound is modulated (note)
Modulation depth for the low-range
0-127
flanger sound
Spaciousness of the low-range
0-180 deg
flanger sound
Proportion of the low-range flanger
sound that is to be returned to the
-98 - +98%
input (negative values invert the
phase)
Delay time from when the original
0.0-100.0 ms sound is heard to when the
high-range flanger sound is heard
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
11 High Rate #2 1-127
12 High Rate 0-21
13 High Depth 0-127
14 High Phase 0-90
15 High Feedback 0-98
16 Balance 0-100
17 Level 0-127
● 0121: Auto Wah
Cyclically controls a filter to create cyclic change in timbre.
No Parameter Value
1 Filter Type 0-1
2 Manual #2 0-127
3 Peak 0-127
4 Sens 0-127
5 Polarity 0-1
6 Rate Mode 0-1
7 Rate #1 1-127
8 Rate 0-21
9 Depth 0-127
10 Phase 0-90
11 Low Gain 0-30
12 High Gain 0-30
13 Level 0-127
22
Rate at which the high-range
0.05-10.00 Hz
flanger sound is modulated (Hz)
Rate at which the high-range
note
flanger sound is modulated (note)
Modulation depth for the
0-127
high-range flanger sound
Spaciousness of the high-range
0-180 deg
flanger sound
Proportion of the high-range
flanger sound that is to be
-98 - +98%
returned to the input (negative
values invert the phase)
D100:0W - Volume balance of the original
D0:100W sound (D) and flanger sound (W)
0-127 Output volume
Description
Type of filter
Lpf: The wah effect will be applied
Lpf, Bpf over a wide frequency range.
Bpf: The wah effect will be applied
over a narrow frequency range.
Adjusts the center frequency at
0-127
which the effect is applied.
Adjusts the amount of the wah
effect that will occur in the range
0-127 of the center frequency. Set a
higher value for Q to narrow the
range to be affected.
Adjusts the sensitivity with which
0-127
the filter is controlled.
Sets the direction in which the
frequency will change when the
autowah filter is modulated. Up:
Up, Down The filter will change toward a
higher frequency. Down: The filter
will change toward a lower
frequency.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
0.05-10.00 Hz Frequency of modulation (Hz)
note Frequency of modulation (note)
0-127 Depth of modulation
Adjusts the degree of phase shift
0-180 deg of the left and right sounds when
the wah effect is applied.
-15 - +15 dB Gain of the low range
-15 - +15 dB Gain of the high range
0-127 Output Level