Related Manuals for Roberts CR9902
Summary of Contents for Roberts CR9902
- Page 1 CR9902 3 Band Dual Alarm Clock Radio CR 9902 CR 9902 CR 9902 CR 9902 3 Band Clock Radio Please read this manual before use...
- Page 2 Controls (Top) C R 9 9 0 2 3 B a n d C lo c k R a d io (Left side) (Right side) 1. Dimmer switch 6. Time set button 11. Alarm set button 2. Alarm selector switch 7.
- Page 3 Controls (Front) 1 5 0 1 7 0 2 1 0 2 4 0 2 6 0 k H z 5 4 0 6 0 0 8 0 0 1 0 0 0 1 3 0 0 1 6 0 0 k H z 1 0 0 1 0 4...
-
Page 4: Switching On And Setting The Time
Switching on and setting the time Before using your clock radio you must first set the correct time. 1. Place the unit on a flat surface. Plug the mains lead into a wall socket 1 5 0 1 7 0 2 1 0 2 4 0 2 6 0... -
Page 5: Listening To The Radio
Listening to the Radio O ff B u z z A u to O n 1. Turn on the radio by sliding the Function switch to the 'On' position. 1 5 0 1 7 0 2 1 0 2 4 0 2 6 0 k H z The LED dial pointer will light up indicating that the radio is switched... -
Page 6: Setting Alarm Times
Setting alarm times The alarms can be set to wake you by either the buzzer or the radio. Your alarm clock radio has 2 separate alarms which can be set to activate at different times. Setting alarm 1 1 + 2 1. -
Page 7: Checking The Alarm Times
3. Whilst holding down the Alarm Set button press the fast forward (Fast) or slow reverse (Slow) buttons to set the required alarm time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected. -
Page 8: Setting The Alarms To Wake To Buzzer
Setting the alarms to wake to buzzer 1 + 2 O ff B u z z A u to O n 1. Set the alarm time as previously described. Set the Function switch to the 'Buzz' position. Set the Alarm selector switch to the ' ' or ' ' position. -
Page 9: Snooze Control
Snooze control The radio or buzzer alarm can be silenced for 7 minutes by pressing the Snooze button. This sequence can be repeated whilst the alarm is sounding. Sleep timer The radio can be set to turn off after a preset time has elapsed. Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps). -
Page 10: Mains Supply
IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN. Mains supply Back-up Battery (not necessary for the unit to function) The CR9902 will operate from a supply of AC 230volts, 50Hz only. Slide the battery cover catch in the direction of the arrow. Remove the battery cover. -
Page 11: Specifications
Frequency Coverage 87.5 - 108MHz Built-in Ferrite aerial 525 - 1610kHz 150 - 260kHz Built-in Ferrite aerial ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH SOUTH YORKSHIRE S64 8YT The Company reserves the right to amend the specification without notice. If you need any further advice, please call our Technical Helpline on :-... - Page 12 In the event that it is not possible to return the instrument to the Roberts dealer from whom it was purchased, please contact Roberts Radio Technical Services department at the address shown below before taking further action.
Need help?
Do you have a question about the CR9902 and is the answer not in the manual?
Questions and answers