Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Roberts CR9953
Summary of Contents for Roberts CR9953
- Page 1 CR9953 2 Band Auto Set Dual Alarm Clock Radio Please read this manual before use...
-
Page 2: Table Of Contents
Contents Contents ... 1 Controls ... 2-4 Switching on ... 5 Setting the time ... 5 Setting the date ... 6 Setting alarm times ... 6 Setting Alarm 1 ... 7 Setting Alarm 2 ... 7 Alarm modes ... 8 Weekday alarm ... -
Page 3: Controls
Controls (top) 1. Time button 2. Sleep button 3. Week Mode button 4. Up button 5. Radio On/Off button 6. Down button 7. Alarm 1 button 8. Snooze button 9. Alarm 2 button 10. Date button 11. Time Zone button If you need any further advice, please call our Technical Helpline on :- 020 8758 0338 (Mon-Fri) Time... - Page 4 Controls (front) 12. Day of week indicators 13. AM indicator 14. Alarm indicator 15. Clock display 16. Low battery indicator 17. Tuning dial...
-
Page 5: Controls
Controls (left and right side) Radio Buzz Radio Buzz Dimmer High If you need any further advice, please call our Technical Helpline on :- 020 8758 0338 (Mon-Fri) 18. Alarm 1 switch 19. Alarm 2 switch 20. Dimmer switch 21. Tuning control 22. -
Page 6: Switching On
Switching on 1. Place your clock radio on a flat surface. Plug the power cord into the wall socket and switch on. 2. After a few seconds the time, day and date will set automatically. Your clock radio is fitted with a long life back-up battery to maintain the factory set time, day and date. -
Page 7: Setting The Date
4. Whilst holding down the Date button set correct date using Up or Down buttons. Setting alarm times Your alarm clock radio has 2 separate alarms which can be set to activate at different times. The alarms can be set to wake you by either the buzzer or the radio. -
Page 8: Setting Alarm 1
Setting alarm 1 1. Press and hold down the Alarm 1 button. 2. Whilst holding down the Alarm 1 button press the Up or Down buttons to set the alarm time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with an AM indicator. Ensure that the correct 12 hour cycle is selected. -
Page 9: Alarm Modes
Alarm modes Your clock radio has three alarm modes for each of the alarms. The alarm modes are Weekdays only - the alarm will switch on Monday to Friday. Weekends only - the alarm will switch on Saturday and Sunday only. -
Page 10: Weekend Alarm
Weekend alarm 1. Press and hold down the Alarm 1 or Alarm 2 buttons (depending on which alarm you wish to set mode for). 2. Whilst holding down Alarm 1 or Alarm 2 buttons repeatedly press and release the Week Mode button until Sat and Sun indicators are lit. 3. -
Page 11: Setting The Alarms To Wake To Buzzer
Setting the alarms to wake to buzzer 1. Set the alarm time as previously described. Set the Alarm 1 or Alarm 2 switch to the “Buzz” position. The Alarm indicator will light. 2. The buzzer alarm will sound every day at the preset time for 1 hour. To switch off the alarm until the next day press the Alarm 1 or Alarm 2 button. -
Page 12: Checking The Alarm Times
2. Tune in to the desired station using the Tuning control. Adjust volume using the Volume control. 3. The Wire aerial located on the rear of your clock radio is for FM reception. The wire should be fully extended and positioned for optimum reception. -
Page 13: Snooze Control
Snooze button. This sequence can be repeated whilst the alarm is sounding. Sleep timer You can program you clock radio to play the radio for up to 90 minutes and then switch off. 1. Press the Sleep button. The display will show the sleep time. -
Page 14: Dimmer Switch
2 years even if it is never connected to a mains supply. If your clock radio was connected to the AC mains supply within a few months after it was manufactured and you experience only short interruptions to the mains supply, your battery may last for up to 2-3 years or even longer. -
Page 15: Changing The Backup Battery
Changing the backup battery 1. Purchase a replacement lithium backup battery type CR2032 or equivalent. 2. Remove the fresh battery from its packaging so that it is ready to install. 3. Important. Maintain connection to AC mains supply during battery replacement. -
Page 16: Time Zones
Time Zones Your clock radio is set up to UK time zone 00 GMT(UTC). Should you wish to take your clock radio to other countries the time zone will need to be reset. 1. Press and hold down the Time Zone button - the display will show the time zone e.g 00. -
Page 17: Specifications
Specifications Power Requirements Mains AC 230 volts, 50Hz Back-up Battery 1 x CR2032 Lithium (2-3 year life) Frequency Coverage 87.5 - 108MHz 522 - 1610kHz The Company reserves the right to amend the specification without notice. If you need any further advice, please call our Technical Helpline on :- 020 8758 0338 (Mon-Fri) Circuit Features Loudspeaker... -
Page 18: General
MW band. Mains supply The CR9953 will operate from a supply of AC 230volts, 50Hz For your convenience this product is supplied with a plug which is fitted with a fuse of the appropriate rating. If the plug supplied is not suitable for your socket outlet, it should be removed by unscrewing the plug top, the terminal screws and removing the cable. -
Page 19: Guarantee
In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please contact Roberts Radio service department at the address shown on the rear of this manual before taking further action. - Page 20 ROBERTS RADIO TECHNICAL SERVICES 97-99 Worton Road Isleworth Middlesex TW7 6EG Technical Helpline :- 020 8758 0338 (Mon-Fri) Issue 1...