Roberts CR9922 Manual
  1. Manuals
  2. Brands
  3. Roberts Manuals
  4. Clock Radio
  5. CR9922
  6. Manual
Roberts CR9922 Manual

Roberts CR9922 Manual

3 band dual alarm clock radio
Hide thumbs
Table of Contents

Advertisement

Quick Links

CR9922
3 Band Dual Alarm
Clock Radio
Please read this manual before use

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CR9922 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Roberts CR9922

Summary of Contents for Roberts CR9922

  • Page 1 CR9922 3 Band Dual Alarm Clock Radio Please read this manual before use...
  • Page 2 Controls 5. Fast forward button 9. Slow reverse button 1. Clock display 13. Alarm 1 indicator 2. Alarm 2 indicator 6. Time set button 10. Snooze button 14. PM indicator 3. Headphone socket (on rear) 7. Alarm set/Off button 11. Alarm type indicators 8.
  • Page 3 Controls 18. Volume control 15. Display brightness switch 16. Alarm selector switch 19. Waveband selector 20. Tuning control 17. Function switch 21. Battery compartment (on underside) If you need any further advice, please call our Technical Helpline on :- 020 8758 0338 (Mon-Fri)

  • Page 4: Switching On And Setting The Time

    Switching on and setting the time Before using your clock radio you must first set the correct time. 1. Place the unit on a flat surface. Plug the mains lead into a wall socket and switch on. 2. The clock display will flash 12:00. 3.

  • Page 5: Listening To The Radio

    Listening to the Radio 1. Switch on the radio by sliding the Function switch to the 'On' position. The LED dial pointer will light up indicating that the radio is switched on. 2. Select the required waveband using the Waveband selector switch. 3.

  • Page 6: Setting Alarm Times

    Setting alarm times The alarms can be set to wake you by either buzzer or the radio alarms. Your alarm clock radio has 2 separate alarms which can be set to activate at different times. Setting alarm 1 1. Slide the Alarm function switch to the ' ' position.

  • Page 7: Checking The Alarm Times

    3. Whilst holding down the Alarm Set button press the fast forward (Fast) or slow reverse (Slow) buttons to set the required alarm time. Release the buttons when the correct alarm time is reached. The clock uses a 12 hour display with a PM indicator. Ensure that the correct 12 hour cycle is selected.

  • Page 8: Setting The Alarms To Wake To Buzzer

    Setting the alarms to wake to buzzer 1. Set the alarm time as previously described. Set the Function switch to the 'Buzz' position. Set the Alarm selector switch to the ' ', ' ' or ' ' position. The corresponding Alarm indicators will light.

  • Page 9: Snooze Control

    Snooze control The buzzer or radio alarm can be silenced for 7 minutes by pressing the Snooze button. This sequence can be repeated whilst the alarm is sounding. Sleep timer The radio can be set to switch off after a preset time has elapsed. Press and hold down the Sleep button until the desired time is reached (maximum 59 minutes in 1 minute steps).
  • Page 10 IF IN DOUBT - CONSULT A QUALIFIED ELECTRICIAN. Mains supply Back-up Battery (not necessary for the unit to function) The CR9922 will operate from a supply of AC 230volts, 50Hz only. Slide the battery cover catch in the direction of the arrow. Remove the battery cover.

  • Page 11: Specifications

    Frequency Coverage 87.5 - 108MHz Built-in Ferrite aerial 525 - 1610kHz 150 - 260kHz Built-in Ferrite aerial ROBERTS RADIO LIMITED PO BOX 130 MEXBOROUGH SOUTH YORKSHIRE S64 8YT The Company reserves the right to amend the specification without notice. If you need any further advice, please call our Technical Helpline on :-...
  • Page 12 In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please contact Roberts Radio service department at the address shown on the rear of this manual before taking further action.

Table of Contents