Roberts Pisa Three CR9935 Manual
  1. Manuals
  2. Brands
  3. Roberts Manuals
  4. Clock Radio
  5. Pisa Three CR9935
  6. Manual

Roberts Pisa Three CR9935 Manual

Pll rds dual alarm clock radio
Hide thumbs
Table of Contents

Advertisement

Quick Links

CR9935
PLL RDS Dual Alarm
Clock Radio
Please read this manual before use

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Pisa Three CR9935 and is the answer not in the manual?

Questions and answers

Wendy
March 29, 2025

How do I advance the time one hour

0
1 comments:
Mr. Anderson
March 29, 2025

To advance the time by one hour on the Roberts Pisa Three CR9935:

1. Press and hold the Time button.
2. While holding the Time button, press the Up button repeatedly until the time advances by one hour.
3. Release the Time button when the correct time is set.

Note: The clock uses the 24-hour format, so 2:30 PM is shown as 14:30.

This answer is automatically generated

0
Wendy
January 29, 2025

How do I switch the sleep mode button off

-1
1 comments:
Mr. Anderson
May 14, 2025

To turn off the sleep mode on the Roberts Pisa Three CR9935 before the preset time expires, press the On/Off button.

This answer is automatically generated

0

Related Manuals for Roberts Pisa Three CR9935

Summary of Contents for Roberts Pisa Three CR9935

  • Page 1 CR9935 PLL RDS Dual Alarm Clock Radio Please read this manual before use...

  • Page 2: Table Of Contents

    Contents Important Information ............1 Radio Data System (RDS) ..........15 Automatic plug and play setup .......... 2 Operating your radio using RDS ........16 Controls ................3-4 Display modes ..............16 Display ................5 Radio text ................ 17 Mains Operation ..............6 Programme type display (PTY) ........

  • Page 3: Automatic Plug And Play Setup

    Automatic Plug and Play setup When your Clock Radio is first connected to the mains supply or after a power failure (when backup battery is not installed), the Auto setup will proceed as follows:- • Automatically search all wavebands and store stations in presets.

  • Page 4: Controls

    Controls 9 10 11 12 (Top) 1. Preset buttons 5. Radio text button 9. Snooze/Night Light button 13. Alarm 1 button 2. Display button 6. Time button 10. Weekend cancel/Traffic button 14. Band button 3. Sleep button 7. Program type button 11.
  • Page 5 Controls (Left side) (Right side) 17. Headphone socket 18. Volume control If you need any further advice, please call our Technical Helpline on :- 020 8758 0338 (Mon-Fri)

  • Page 6: Display

    Display 1. Waveband indicators 8. Weekend cancel indicator 2. Auto time indicator 9. Sleep time indicator 3. Traffic information indicator 10. Radio text indicator 4. Enhanced other networks indicator 11. Programme type indicator 5. RDS indicator 12. Alarm 2 indicators 6.

  • Page 7: Mains Operation

    Mains operation 1. Place your radio on a flat surface. 2. Plug the mains plug into a wall socket and switch on the wall socket. Display backlight The display back light will be switched on for 10 seconds whenever any button is pressed.

  • Page 8: Setting The Clock Automatically

    Setting the clock automatically The clock time and day of week can be set automatically when receiving an RDS station that transmits clock time (CT). The CT information is transmitted once every minute. If the station has sufficient signal strength the clock will set within one or two minutes. 1.

  • Page 9: Setting The Clock Manually

    Setting the clock manually 1. Ensure that the radio is switched off. 2. Repeatedly press the Time button until the auto time symbol is removed from the display. 3. Press and hold down the Time button. 4. Whilst the Time button is held down set the time by pressing the Up or Down buttons.

  • Page 10: Setting The Alarm Time

    Setting the alarm times 1. Press and hold down the Alarm 1 or Alarm 2 buttons. 2. Whilst the Alarm 1 or Alarm 2 button is held down set the alarm time by pressing the Up or Down buttons. The clock uses the 24 hour system e.g.

  • Page 11: Wake To Radio

    Wake to radio 1. Set the alarm time as previously described. 2. Press and release the Alarm 1 or Alarm 2 button until the symbol appears in the display. 3. At the preselected time the radio will switch on. The radio will switch off automatically after 90 minutes.

  • Page 12: Weekend Alarm Cancel

    Weekend alarm cancel 1. Your clock radio can be set to automatically cancel alarms at the weekend. Ensure that your clock radio is switched off. 2. Press the WEC/Traffic button until the WEC symbol appears in the display. The alarm will now only sound on weekdays. 3.

  • Page 13: Operating Your Radio - Manual Tuning

    Operating your radio - manual tuning 1. Switch on your radio by pressing the On/Off button. 2. Select the required waveband by pressing the Band button. The waveband selected will appear in the display. On FM fully extend the pigtail aerial from the rear of your clock radio. On MW rotate your radio for best reception.

  • Page 14: Presetting Stations

    Pre-setting stations You may store up to 10 different stations on each of the two wavebands giving a total of 20 preset stations. 1. Switch on your radio using the On/Off button. 2. Select the desired waveband using the Band button. 3.

  • Page 15: Recalling A Preset Station

    Recalling a preset station 1. Switch on your radio using the On/Off button. 2. Select the desired waveband using the Band button. 3. Press one of the Preset buttons to recall the station. Presets 6 to 10 are obtained by pressing the Preset button twice. Last station memory 1.

  • Page 16: Radio Data System (Rds)

    Radio Data System (RDS) The Radio Data System (RDS) is a system in which inaudible digital information is transmitted in addition to the normal FM radio programme. RDS offers several useful features, the following are available on your radio:- Programme Identification (PI) Clock Time (CT) automatic adjustment This information consists of a code, which is assigned to each individual The Clock Time information transmitted from the broadcasting station...

  • Page 17: Operating Your Radio Using Rds

    Operating your radio using RDS (Radio data system) 1. Switch on your radio and select the FM waveband. 2. Tune into a station, the display will indicate frequency for two seconds and then change to show the station name. The symbol will appear in the display 3.

  • Page 18: Radio Text

    Radio Text (RT) The RDS system provides a text message of up to 64 characters in length. It is displayed by scrolling the characters of the message from right to left. 1. Switch on your radio and select the FM waveband. Tune into a station carrying RDS information.

  • Page 19: Programme Type Search

    Programme Type search (PTY) 1. To search for a station of a particular type, repeatedly press and release the PTY button until the required programme type is shown in the display. Press and release either the Up or Down buttons. 2.
  • Page 20 5. If the station carries Enhanced Other Network information the EON symbol will appear in the display. The radio will automatically tune to other stations transmitting traffic information. When the traffic announcement has finished the radio will re-tune to the previously selected station.

  • Page 21: Demonstration Mode

    Demonstration mode Your radio is equipped with a demonstration mode which when active highlights the main features available on your clock radio. 1. Press and hold down the Display button until the display enters Demonstration mode. 2. Press any key to cancel demonstration mode. Headphones 1.

  • Page 22: General

    Fuse General Do not allow this unit to be exposed to moisture (e.g. dripping or This apparatus must be protected by a 3A fuse (BS1362) in a 13A plug (BS1363). If another type of plug is used a 5A fuse should be fitted in splashing) or to temperatures exceeding 70 degrees centigrade.

  • Page 23: Specifications

    Specifications Circuit Features Power Requirements Loudspeaker 77mm 8ohms Mains AC 230 volts, 50Hz only Batteries 2 x LR6 (AA size) for clock/memory Output Power 500mW into 8ohms Headphone socket 3.5mm dia Frequency Coverage Aerial System FM Wire aerial 87.5-108MHz 522- 1620kHz Built-in Ferrite aerial The Company reserves the right to amend the specification without notice.
  • Page 24 In the event that it is not possible to return the instrument to the Roberts' dealer from whom it was purchased, please contact Roberts Radio Technical Services at the address shown below. These statements do not affect the statutory rights of a consumer.

Table of Contents

Save PDF