Table of Contents
Advertisement
. VOLUME
up /
Used to adjust the volume on amplifier and other components
equipped with volume control.
⁄0 CURSOR/TRANSPORT CONTROL buttons
Used to operate on-screen and other displays used by amplifier and
other components, as well as to operate the PLAY, STOP, PAUSE,
NEXT, and PREVIOUS functions of each source.
⁄1 < • 3 (CURSOR/ TRANSPORT
CONTROL switching) button
Used to switch the function of the CURSOR/ TRANSPORT CONTROL
buttons ⁄0 between the CURSOR and TRANSPORT CONTROL
functions, with the currently selected function displayed on the LCD
when the DVD, LD, or VCR functions are selected. When functions
other than DVD, LD, or VCR are selected, the < • 3 button remains
inactive.
⁄2 Channel
up /
Used to controls the up/down function of tuner, or to cycle through the
tuner presets.
⁄3 MUTE button
Used to temporarily mute the sound for preamplifiers, receivers, etc.
⁄4 GUIDE button
Used to call up the on-screen menus used to control DVD players,
digital satellite systems (DSS), and other menu-equipped systems.
⁄5 CLEAR button
Used to clear the contents of memory or programmed functions.
⁄6 MEMO button
Used to program your CD player's track memory, or to enter a VCR
recording program, and can be used to provide the MEMO function
included with other components in your system.
⁄7 Ten-Key pad/Surround Mode buttons
Used to enter numeric digits, useful for finding a specific track on a
CD or DVD, etc. When the function is set to AMP, it is possible to
choose Surround Mode, etc.
⁄8 Infrared Transmitter/Receiver Window
Used to transmit remote control signals based on beams of infrared
light to system components. To ensure that these signals are
properly received, make sure that this window is pointing in the
general direction of the infrared receiver on the amplifier or other
components. This window should also be pointed toward the source
remote controller when using Programmable Learning function.
Note:
The MODE z , MACRO x , Jog Dial n and < • 3 (CURSOR/
TRANSPORT CONTROL switching) ⁄1 cannot be programmed.
down buttons
down buttons
LCD (Liquid Crystal Display)
Information about currently selected functions and modes is
displayed on the LCD. Pressing any buttons will call up a full display
of information on the status of that function or mode. This display will
disappear after approximately 1 minute, except for the Function
Name indicator a, which is always displayed.
a
b
i
c
e
f
a Function Name indicator
Displays the name of the currently selected function (LD, TV, etc.)
using up to 5 characters.
b Command Name indicator
Displays up to 10 types of commands for each function using up to 5
characters.
c Command Page indicator
Allows confirmation of current command page. Also, when setting or
transmitting macros, displays information such as the number of
macro steps and the time intervals between command transmissions.
d Transmission indicator
Indicates when the remote controller is transmitting a signal.
e USE indicator
For normal operation the USE indicator is displayed.
f LEARN indicator
Indicates when the remote controller is in the LEARN mode.
g NAME indicator
Indicates when the remote controller is in the NAME mode and a
function name is being changed.
h MACRO indicator
Indicates when the remote controller is in the MACRO mode.
i CURSOR indicator
Indicates when the CURSOR/TRANSPORT CONTROL button is in the
cursor mode.
j CONTROL indicator
Indicates when the < • 3 (CURSOR/TRANSPORT CONTROL
switching) ⁄1 is in a transport control mode such as PLAY, STOP, etc.
• If the LCD flickers when a button is pressed in order to transmit a
command or when in the LEARN mode, the transmission or
learning is not possible. In such a case, please replace the
batteries.
• This remote controller uses non-volatile memory, so that learned
codes and macros will be preserved even if the batteries are
removed.
22
j
d
h
g
Advertisement
Table of Contents
