Marantz PS-17 User Manual page 37

3. Erasing Jog Dial Codes
To clear all codes and names previously set for each of the
functions (LD, TV, etc.).
1) Press the function you want to erase.
2) Hold down the CLEAR button ⁄5 and press both ENT
buttons m at the same time. LCD b will display CLR?.
ENT
CH
C D
DSS T V
L D TUNER
CLEAR MEMO
2
AUTO
1 2
Dolby H P-DIRE.
3) If you wish to continue the clearing operation, press the
Cursor button ⁄0 . This will return all 10 commands in the Jog
Dial to their factory presets, or leave them empty if no factory-
presets are available. Accordingly, the LCD
the factory preset displays, or will simply be empty.
CH
C D
• Use a similar operation to erase the Jog Dial codes for each
function.
• To cancel the memory clearing operation, do not press
Cursor button ⁄0 and simply touch any other button.
4. Erasing Code s by Function
To clear all codes and names previously set for each of the
functions (LD, TV, etc.), press and hold the CLEAR button ⁄5 ,
then press the button for the function to be cleared twice. CLR?
will appear on LCD b. If you wish to continue the clearing
operation, press the OK Cursor button ⁄0 .
C D
DSS T V
L D TUNER
CLEAR MEMO
2
AUTO
1 2
Dolby H P-DIRE.
This will return the button to its factory-presets or leave it empty if
no factory presets are available. Accordingly, the LCD b will
return to the factory preset displays, or will simply be empty.
• To cancel the memory clearing operation, do not press the
OK Cursor button ⁄0 and simply touch any other button.
• The codes for the < • 3 button ⁄1 cannot be cleared.
ENT
VOL
OK
DVD
CD-R/MD
VCR PHONO
TAPE AMP
GUIDE MUTE
SRS 6.1 5ch-ST.
3 4 5
2CH OSD SLEEP
b will return to
VOL
OK
DVD
CD-R/MD
DVD
CD-R/MD
VCR PHONO
TAPE AMP
GUIDE MUTE
SRS 6.1 5ch-ST.
3 4 5
2CH OSD SLEEP
PROGRAMMING MACROS
Macros make it possible to use a single function button to perform
more complex series of operations that would normally require
pressing several buttons. A single button can be programmed to
perform up to 10 steps in sequence. A typical example of such a
series might be as follows:
• Turn the main amplifier power ON
Set the Surround Mode to Pro Logic
fi Set the laser disc player to PLAY.
• No signals may be transmitted during macro programming.
• The various steps that make up a macro are set initially to be sent
one after another in 1 second intervals, however these intervals
may be shortened to as little as 0.5 seconds or lengthened to as
much as 5 seconds using the Setup mode.
• In the macro mode, the number of steps the macro contains is
displayed on LCD c. Macros may be programmed for each of the
11 function buttons, from LD to AMP.
1. Use a ballpoint pen or other sharp point to press the MACRO
button x until the MACRO and LEARN indicators are displayed
blinking on the LCD.
OK
ON
LEARNING REMOTE
CONTROL RC-17PS
Press the Function button , for which you wish to program a
2.
series of operations. In this case, let's use the example of the
laser disc player.
Press the LD Function button ,. The LCD a will display LD-M.
Characters displayed on LCD a include the following,
depending on the function button for which the macro is being
programmed:
LD-M, DVD-M, TV-M, DSS-M, VCR-M, AUX-M, TUN-M, CD-M, TP-
M, AMP-M, CDR-M (or MD-M for remote controller set for MD).
OK
• If a macro has already been set for the selected function
button, the LCD a will blink. Also, the number of steps in the
macro is displayed on LCD c.
27
fi Switch the function to LD
fi Switch the TV to video input
POWER
SOURCE
OFF
ON / OFF
MACRO MODE
fi