Marantz PS-17 User Manual page 36

REWRITING NAMES
This remote controller allows the names accessible by Jog Dial
control n to be rewritten with new ones of your choosing.
• Rewriting of names is performed for each individual function.
• Let's use a laser disc player as an example to show how to change
the 's "SIDE-A" to "LD-A".
Use a ballpoint pen or other sharp point to press the MODE
1.
button z to switch the remote controller to the NAME mode. The
NAME indicator blinks.
Press the LD Function button ,.
2.
DSS
L D
CLEAR
AUTO
1
Dolby H
6
Use the Jog Dial n to select the page for which you wish to enter
3.
a new name.
4. The character on the left-hand side of the Command Name
indicator on LCD b will flash, indicating that it is the character
ready to be rewritten. New characters entered will be written over
the top of the current character so that the current character is
erased.
Use the < and > Cursor buttons ⁄0 to select the characters to be
rewritten.
Use the ten-key pad ⁄7 to select the desired alphanumeric
5.
characters.
Pressing the number buttons on the ten-key pad will cycle
through the alphanumeric characters as follows:
Ten keypad Press, press again, press again, etc.
1 A fi B fi C fi 1 fi A
2 D fi E fi F fi 2 fi D
3 G fi H fi I fi 3 fi G
4 J fi K fi L fi 4 fi J
5 M fi N fi O fi 5 fi M
6 P fi Q fi R fi 6 fi P
7 S fi T fi U fi 7 fi S
8 V fi W fi X fi 8 fi V
9 Y fi Z fi / fi 9 fi Y
0 SPACE fi + fi — fi , fi ' fi 0 fi SPACE ( )
6. Therefore, to enter the letter "L", press the 4-key on the ten-key
pad ⁄7 3 times in a row to cycle from J to K to L.
Once the desired character "L" appears, press either of the <
and > Cursor buttons ⁄0 and the L will be permanently written
over the former character. Press the 0-key in order to replace
unneeded extra characters with spaces.
T V VCR PHONO
TUNER TAPE AMP
MEMO GUIDE MUTE
2
SRS 6.1 5ch-ST.
2 3 4 5
P-DIRE. 2CH OSD SLEEP
7 8 9 0
7. Follow the same procedure to enter "D-A". When finished, press
the OK Cursor button ⁄0 . Pressing OK permanently fixes the
newly written characters.
• Up to 5 alphanumeric characters may be entered in the
Command Name indicator of the LCD.
• To rewrite the names of the other items in the Command
Name indicator, use the Jog Dial n to select the desired
command and repeat from step 5.
8. When you are finished rewriting, use a ballpoint pen or other
sharp point to press the MODE button z to return the remote
controller to the USE mode. The USE indicator is displayed on
the LCD, and the newly programmed codes now can be used.
ERASING PROGRAMMED CODES
(Returning to Factory Presets)
Codes that have been programmed into the memory can be erased in
3 ways: by button(s), by function(s), and by Jog Dial command.
1. Use a ballpoint pen or other sharp point to press the MODE
button z to switch the remote controller to the LEARN mode, so
that the LEARN indicator is blinking on the LCD.
Note:
Erasing of programmed codes is only possible in the LEARN
mode.
2. Erasing by Button(s)
To erase the codes and names programmed for any button,
press and hold the CLEAR button ⁄5 , then press the button to be
erased twice. This will return the button to its factory presets or
leave it empty if no factory presets are available.
Jog Dial codes may be erased in the same way, by pressing and
holding the CLEAR button ⁄5 while using the Jog Dial n to call
up the command to be erased, then pressing one of the ENT
buttons m on either side of the Jog Dial n twice. This will return
the button to its factory presets or leave it empty if no factory
presets are available.
To erase codes programmed for the CLEAR button ⁄5 , simply
press the CLEAR button ⁄5 continuously for 3 seconds.
As an example, let's clear the PLAY command from the laser disc
player command set.
26
POWER
SOURCE
ON OFF
ON / OFF
LEARNING REMOTE
CONTROL RC-17PS MACRO MODE
ENT ENT
CH VOL
OK
C D DVD CD-R/MD
DSS T V VCR PHONO
L D TUNER TAPE AMP
CLEAR MEMO GUIDE MUTE
2
AUTO SRS 6.1 5ch-ST.
1 2 3 4 5