Hitachi L700 SERIES Instruction Manual page 251

Code Function name
C001 Terminal [1] function (*2)
C002 Terminal [2] function
C003 Terminal [3] function (*2)
C004 Terminal [4] function
C005 Terminal [5] function
C006 Terminal [6] function
C007 Terminal [7] function
C008 Terminal [8] function
C011 Terminal [1] active state
C012 Terminal [2] active state
C013 Terminal [3] active state
C014 Terminal [4] active state
C015 Terminal [5] active state
C016 Terminal [6] active state
C017 Terminal [7] active state
C018 Terminal [8] active state
C019 Terminal [FW] active state
*2 When the emergency stop function is enabled (SW1 = ON), "18" (RS) and "64" (EMR) are forcibly written to parameters "C001" and "C003", respectively. (You cannot
arbitrarily write "64" to "C001".) If the SW1 signal is turned off and then turned on, "no" (no assignment) is set in parameter "C003".
Monitored data or setting
01 (RV: Reverse RUN), 02 (CF1: Multispeed 1 setting),
03 (CF2: Multispeed 2 setting), 04 (CF3: Multispeed 3 setting),
05 (CF4: Multispeed 4 setting), 06 (JG: Jogging),
07 (DB: external DC braking),
08 (SET: Set 2nd motor data), 09 (2CH: 2-stage acceleration/deceleration),
11 (FRS: free-run stop), 12 (EXT: external trip),
13 (USP: unattended start protection), 14: (CS: commercial power source
enable), 15 (SFT: software lock), 16 (AT: analog input voltage/current select),
17 (SET3: 3rd motor control), 18 (RS: reset),
20 (STA: starting by 3-wire input), 21 (STP: stopping by 3-wire input),
22 (F/R: forward/reverse switching by 3-wire input), 23 (PID: PID disable),
24 (PIDC: PID reset), 26 (CAS: control gain setting),
27 (UP: remote control UP function),
28 (DWN: remote control DOWN function),
29 (DWN: remote control data clearing), 31 (OPE: forcible operation),
32 (SF1: multispeed bit 1), 33 (SF2: multispeed bit 2),
34 (SF3: multispeed bit 3), 35 (SF4: multispeed bit 4),
36 (SF5: multispeed bit 5), 37 (SF6: multispeed bit 6),
38 (SF7: multispeed bit 7), 39 (OLR: overload restriction selection),
40 (TL: torque limit enable), 41 (TRQ1: torque limit selection bit 1),
42 (TRQ2: torque limit selection bit 2), 43 (PPI: P/PI mode selection),
46 (LAC: LAD cancellation),
50 (ADD: trigger for frequency addition [A145]),
51 (F-TM: forcible-terminal operation),
53 (KHC: cumulative power clearance),
56 (MI1: general-purpose input 1), 57 (MI2: general-purpose input 2),
58 (MI3: general-purpose input 3), 59 (MI4: general-purpose input 4),
60 (MI5: general-purpose input 5), 61 (MI6: general-purpose input 6),
62 (MI7: general-purpose input 7), 63 (MI8: general-purpose input 8),
64(EMR: Emergency stop signal),65 (AHD: analog command holding),
74 (PCNT: pulse counter), 75 (PCC: pulse counter clear),
no (NO: no assignment)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
00 (NO) / 01 (NC)
8 - 9
Chapter 8 List of Data Settings
Default
_FF
18
(*2)
16
03
(*2)
02
01
06
11
13
00
00
00
00
00
00
00
00
00
Setting Change
during during
operation operation Page
(allowed (allowed
or not) or not)
4-47
4-48