Summary of Contents for KitchenAid PRO LINE KHEV01RSS0
Page 1
Ki|chen_kid PRO LINE ®FRONT-LOADING ELECTRIC DRYER 3 f_4 ,ii _o,_: ....... _; ... For questions about features, operation/performance, parts, accessories or service, call: 1-800-422-1230 or visit our website at... www.kitchenaid.com Table of Contents ......................3957654...
DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER"...
INSTALLATION INSTRUCTIONS For close-clearance installations between 33" (83.8 cm) and 38" (96.5 cm), see "Plan Vent System" section for venting requirements. Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Dryer Dimensions Explosion H azard 42"** (I 06.7 Keep flammable materials and vapors, such as gasoline, away from dryer, Place dryer at least 18 inches (46 cm) above the floor for a garage installation. Failure to do so can result in death, explosion, or fire.
Page 6
Recommended installation spacing for cabinet installation, with or without a pedestal It is your responsibility • For cabinet installation, with a door, minimum ventilation • To contact a qualified electrical installer. openings in the top of the cabinet are required. •...
Page 7
If using a power s upply cord: If connecting by direct wire: Use a ULlisted power supply c ordkitmarked forusewith Power supply cable must match power supply (4-wire or 3-wire) clothes d ryers. The kitshould contain: and be: [] AULlisted 30-amp p ower s upply c ord, r ated Flexible armored cable or nonmetallic sheathed copper cable 120/240 voltminimum.
Page 8
_:_u _'_ '! _ ' _° Direct Wire Power Supply Cord Fire Hazard Fire Hazard Use 10 gauge solid copper wire. Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Use a UL listed strain relief. Disconnect power before making electrical connections.
Put power supply cord through the strain relief. Be sure Electrical Connection Options that the wire insulation on the power supply cord is inside If your home has: And you will be Go to Section the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position.
Page 10
Remove center silver-colored terminal block screw. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire 7.
Page 11
Loosen or remove center silver-colored terminal block screw. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block.
Page 12
When connecting to the terminal block, place the hooked end of Optional 3-wire connection the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown. Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.
Page 13
• Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance. • Do not install flexible metal vent in enclosed walls, ceilings or floors. Elbows 45 ° elbows provide better airflow than 90 ° elbows. Fire Hazard Use a heavy metal vent.
Choose your exhaust installation type Determine vent path Recommended exhaust installations • Select the route that will provide the straightest and most direct path outdoors. This dryer vents from the rear of the dryer. • Plan the installation to use the fewest number of elbows and turns.
1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check that you have all of your tools. Excessive Weight Hazard 3. Check the dryer's final location. Be sure the vent is not crushed or kinked.
Page 17
• Press TEMP until the desired temperature illuminates. Remove the load from the dryer as soon as tumbling stops to reduce wrinkling. This is especially important for permanent NOTE: During a Manual Cycle, you can change the settings press, knits and synthetic fabrics. for Time, Temperature, Extra Care and Cycle End Tone signal.
Check Lint Screen Delicate The Check Lint Screen display reminds you to check the lint Use this cycle to get Low heat for drying synthetic fabrics, washable knit fabrics and no-iron finishes. screen. CHECK LINT SCREEN is displayed when the machine is turned on.
Page 19
Manual Preset Cycle Settings Manual Cycles Temp. Default Time Use these settings to select temperatures for the Manual Cycles. Load Type (Minutes) Press the TEMP key until the desired temperature setting glows. Temperature settings cannot be used with the Automatic Cycles.
Place drying rack inside dryer drum, positioning the back wire on the ledge of the inner dryer back panel. Push down on DRYER CARE front feet of drying rack, at the same time, aligning the locater tabs with the locater indentations in the dryer drum.
To wash 1. Roll lint off the screen with your fingers. 2. Wet both sides of lint screen with hot water. From Inside the Dryer Cabinet 3. Wet a nylon brush with hot water and liquid detergent. Scrub Lint should be removed every 2 years, or more often, depending lint screen with the brush to remove residue buildup.
TROUBLESHOOTING First try the solutions suggested here and possibly avoid the cost of a service call... Dryer will not run Clothes are not drying satisfactorily, drying times are too long, or load is too hot Has a household fuse blown, or has a circuit breaker tripped? is the lint screen clogged with lint?
• Was dryer fabric softener properly used? If you need further assistance, you can write to KitchenAid with Add dryer fabric softener sheets at the beginning of the cycle. any questions or concerns at: Fabric softener sheets added to a partially dried load can KitchenAid Brand Home Appliances stain your garments.
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE. Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchenAid dealer to determine if another warranty applies.