KitchenAid PRO LINE KHEV01RSS0 Use & Care Manual page 17

• Press TEMP until the desired temperature illuminates.
4.
5.
NOTE: During a Manual Cycle, you can change the settings
for Time, Temperature, Extra Care and Cycle End Tone signal.
Press PAUSE/CANCEL twice to stop the dryer and clear the
settings. Select another cycle or option.
(OPTIONAL STEP) If desired, set the Cycle End Tone signal.
Select LOUD or SOFT to alert you when a cycle ends.
Press and hold START for approximately 3 seconds until
dryer starts. Be sure the door is closed.
• If you do not press Start within 5 minutes of selecting the
cycle, the dryer automatically shuts off.
• If you wish to end your drying cycle after pressing Start,
press PAUSE/CANCEL twice.
To stop your dryer at any time
Press PAUSE/CANCELtwice or open the door.
To pause the dryer at any time
Open the door or press PAUSE/CANCEL once.
To restart the dryer
Close the door. Press and hold START until dryer starts.
NOTE: Drying will continue from where the cycle was interrupted
if you close the door and press Start within 5 minutes, If the cycle
is interrupted for more than 5 minutes, the dryer will shut off.
Select new cycle settings before restarting the dryer.
This feature allows you to lock your settings to prevent
unintended use of the dryer. You can also usethe Control Locked
feature to prevent unintended cycle or option changes during
dryer operation.
To enable the Control Locked feature when dryer is
running:
Press and hold the DRY RACK button for 3 seconds. The control
is locked when a single beep is heard and the Control Locked
icon is displayed in the status window. The icon is located next to
the Dry Rack button and will illuminate when control locked.
• When the dryer is off, it is not necessary to turn the control on
before activating the Control Locked feature.
To unlock:
Press and hold the DRY RACK button for 3 seconds to turn this
feature off.
NOTE: When the dryer is running and Control Locked is on, the
dryer can be stopped by pressing the PAUSE/CANCEL button,
but can't be restarted until the control is unlocked.
Select the correct cycle and dryness level or temperature for your
load. If an Automatic Cycle is running, the display shows the
estimated cycle time when your dryer is automatically sensing
the dryness level of your load. If a Manual Cycle is running, the
display shows the exact number of minutes remaining in the
cycle.
Cool Down tumbles the load without heat during the last few
minutes of all cycles. Cool Down makes the loads easier to
handle and reduces wrinkling. The length of the Cool Down
depends on the load size and dryness level.
Drying tips
• Follow care label directions when they are available.
Remove the load from the dryer as soon as tumbling stops to
reduce wrinkling. This is especially important for permanent
press, knits and synthetic fabrics.
Avoid drying heavy work clothes with lighter fabrics. This
could cause overdrying of lighter fabrics, leading to increased
shrinkage or wrinkling.
Cycle tips
• Dry most loads using the preset cycle settings.
• Refer to the Automatic or Manual Preset Cycle Settings chart
(in the "Cycles" section) for a guide to drying various loads.
Drying temperature and Dryness Level are preset when
you choose an Automatic Cycle. You can choose a
different dryness level, depending on your load by
pressing the DRYNESS LEVEL button to select MORE or
LESS.
• If you wish to adjust the cycle length of a Manual Cycle,
you must press plus (+) or minus (-) buttons. Adjust the
temperature of a Manual Cycle by pressing TEMP until
the desired temperature is selected.
NOTE: You cannot choose a Dryness Level with Manual
Cycles.
.... i'
Messages on the status display help you to follow the progress of
your dryer.
Estimated Time
Remaining Status
Wet
WET is displayed at the beginning of the Automatic or Manual
Cycle if a wet item is detected.
• In an Automatic Cycle, if a wet item is not detected after
5 minutes, the dryer goes directly into Cool Down. COOL
DOWN will be displayed, along with EXTRA CARE, if
selected.
• In a Manual Cycle, if a wet item is not detected, the dryer will
continue to run for the length of time selected, but WET will
not be displayed.
Damp
DAMP is displayed if the load has reached the damp dry level.
NOTE: DAMP will not be displayed with Manual Cycles.
Cool Down
COOL DOWN is displayed during the cool down part of the cycle.
Laundry cools for ease in handling.
Cycle Complete
CYCLE COMPLETE is displayed when a drying cycle is finished,
If the Extra Care feature is selected, EXTRA CARE will also be
displayed.
The Cycle Complete display turns off 1 hour after the end of a
drying cycle, when PAUSE/CANCEL is pressed, or when the door
is opened. If the Extra Care feature is selected, the Cycle
Complete display will remain on 1 hour after the Extra Care cycle
stops.
Extra Care
EXTRA CARE is displayed when this option is selected. This
display stays on with the Cycle Complete display. See "Addtional
Features,"
17