Table of Contents
Advertisement
General Care & Cleaning
FEATURE
OVERVIEW
Cleaning
Recommendations
for Ceramic
Glass Cooktops
(cont'd.)
Care & Cleaning
of Stainless
Steel / Removing
& Replacing
Oven Door
Do not use the following
on the ceramic
glass cooktop:
Do not use abrasive
cleaners
and scouring
pads, such as metal and some
nylon pads. They may scratch
the cooktop,
making
it more difficult
to clean.
Do not use harsh cleaners,
such as chlorine
bleach,
ammonia
or oven
_
i
cleaners'
as they may etch °r disc°l°r
the c°°kt°p"
1_=_I
Do thOt UoSed ior ty s p otgts
n; IbOtrhSOnrtlaPeer
tOWseles_la:c t h: Ya;aon n !eave
soil or lint
Special Caution
for Aluminum
Foil and Aluminum
cooking
utensils:
• Aluminum Foil - Use of aluminum foil will damage the ceramic cooktop. Do not use thin aluminum cooking utensils or
allow aluminum foil to touch the ceramic cooktop under ANY circumstances.
• Aluminum
utensils
- The melting point of aluminum is much lower than that of other metals. Care must be taken when
aluminum pots or pans are used on the cooktop. If allowed to boil dry, not only will the utensil be destroyed, but it may
fuse to, break or mark the ceramic glass surface, permanently damaging the cooktop surface.
Care
and Cleaning
of Stainless
Steel
(some
models)
Some models are equipped with Stainless Steel exterior parts. Special care and cleaning are required for maintaining the
appearance of Stainless Steel parts. Please refer to the Care & Cleaning Table provided at the beginning of the Care &
Cleaning
section in this Use & Care Guide.
Fig. 2
Removing
and
Replacing
the Oven
Door
The door is heavy. For safe, temporary storage, lay the door flat
with the inside of the door facing down.
To Remove
Oven Door:
1.
Open oven door completely
(horizontal
with floor - See Fig. 1).
2.
Remove 2 screws located on the inside of the door liner (See A Fig. 2)
3.
Insert the 2 screws into the door hinge holes located on the side of the hinge arm,
one into each hinge (See B Fig. 2).
4.
Close oven door until the door stops, (Do not force the door to close any further).
The placement of these screws should keep door open in about a 45 degree
position.
5.
Grasp oven door firmly on both sides and slide door up and off hinges at the same
angle. (See Fig. 3)
6.
To clean oven door follow the instructions
in the Care & Cleaning
Table.
or
us8
Fig. 3
about 45
Hinge
To Replace
Oven Door:
1.
Be sure the hinge arms remain at the 45 degree angle position. Be sure the
screws are still locking the hinge arms from moving. If the screws fall out of the
hinge holes, the hinge(s) may snap back against the oven frame and could pinch
fingers or chip the porcelain finish on the oven front frame.
2.
Hold door at the sides near the top while resting the lower front of door on your
knee. Insert the door channels at the bottom of door over the door hinges, (See
Fig. 3).
3.
Allow the door to slide down into the door hinges evenly at the same 45 degree
angle. The hinge arms should be inserted into the bottom corners as far as they
can go.
4.
Open door completely
(horizontal with floor) and remove both screws from holes
in door hinges.
5.
Reinstall the 2 screws into the door liner (See C Fig. 2).
6.
If the door is not in alignment with the oven frame, remove door and repeat the
above steps.
34
Advertisement
Table of Contents
