Table of Contents
Advertisement
Quick Links
INSTALLATION
AND SERVICE
MUST BE PERFORMED
BY A QUALIFIED
INSTALLER.
IMPORTANT:
SAVE FOR LOCAL
ELECTRICAL
iNSPECTOR'S
USE.
READ AND SAVE THESE
INSTRUCTIONS
FOR FUTURE
REFERENCE.
if the information
in this manual
is not followed
exactly,
a fire
or explosion
may
result
causing
property
damage,
personal
injury or death.
FOR YOUR SAFETY:
--
Do not store or use gasoline
or other flammable
vapors
and liquids in the vicinity of this or any other appliance.
--
WHAT TO DO IF YOU SMELL
GAS:
- Do not try to light any appliance.
• Do not touch
any electrical
switch; do not use any phone
in your building.
- Immediately
call your gas supplier
from
a neighbor's
phone.
Follow the gas supplier's
instructions.
- if you cannot
reach
your
gas supplier,
call the
fire
department.
--
Installation
and service must be performed
by a qualified
installer,
service
agency
or the gas supplier.
Refer to your serial plate for
applicable agency certification
• ALL RANGES
CAN TiP
• INJURYTO
PERSONS
COULD
RESULT
• iNSTALL
ANTI=TIP
DEVICE
PACKED
WiTH
RANGE
e SEE iNSTALLATiON
iNSTRUCTiONS
Note: For appliances
installed
in the
State of Massachusetts
see page 2.
OVERALL
DIMENSIONS
25 3/4"
FRONT
SIDE
VIEW
VIEW
'_
*Minimum to --
30"
/
Side Wall
Minimum
on Either
"5 "-_"
47-3/4"
Side of
_-
Maximum
36 + 1/8"
Range 5"
r__..Lr__.
36"
Clearances
and
Dimensions
1.
Location--Check
location where
the range will be installed. Check
for
proper
electrical
and gas
supply,
and the stability
of the
floor.
2.
Dimensions
that are shown must
be used.
Given
dimensions
provide
minimum
clearance.
Contact
surface
must
be solid
and level.
pin 316259339 (0607) EN
Minimum to
1_-13"-_1
,, Cabinets on
Maximum Depth
Either Side
for Cabinets
of Range.
Above Range Top.
30"
_
0" Clearance
Below
Cooking
Top and at Rear
of Range.
Provide
Proper
Fuel
Type
Before Proceeding: Your range is preset to operate on natural gas only. This
model was shipped convertible
from the factory with the necessary
parts and
conversion instructions supplied.
DO NOT attempt to convert this range to LP/Propane settings without
the proper LP/Propane conversion kit provided with the range or obtained from your
dealer.
Follow all instructions provided with this conversion kit.
Espa_olp
9-16
Advertisement
Table of Contents
Related Manuals for Kenmore 79079443601
Summary of Contents for Kenmore 79079443601
- Page 1 INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. if the information in this manual is not followed exactly, a fire or explosion result causing property damage,...
-
Page 2: Important Safety Instructions
important Notes to the Installer Never leave children alone or unattended Read all instructions contained in these installation in the area where an appliance is in use. As children grow, instructions before installing range. teach them the proper, safe use of all appliances. Never leave Removeall packing material from the oven compartments the oven door open when the range is unattended. -
Page 3: Before Starting
Before Starting Locate the Bracket Using the Template- (Bracket may be located on either the left or right side of the range. Use Tools You Will Need the information below to locate the bracket if template is For leveling legs and Anti=Tip Bracket: not available). - Page 4 Level and Position Range- Level range by adjusting the (4) leveling legs with a wrench. Note: A minimum clearance of 1/8" is required between the bottom of the range and the leveling leg to allow room for the bracket. Use a spirit level to check your adjustments.
-
Page 5: Please Read Carefully
5. Read electrical connection details below Manual Flare Flexible Flare Union Pressure and connect electricity to range. Shutoff Union Appliance Adaptor Regulator Before servicing, disconnect electrical supply at circuit breaker, fuse or power cord. Electric Requirements: An individual, properly grounded and polarized branch circuit protected bya 15amp. - Page 6 6. Assembly of Burner Heads & Burner Caps (for Deep Well Cooktop models only) Your range is shipped with the Burner Heads and Burner Caps in the correct locations. Packing material is located between the Burner Heads and the cooktop. a.
- Page 7 Burner Flame Size 5/8" i. - ---_l Main Adjust flame until you can quickly turn knob from LITE to LOWEST POSITION without extinguishing the flame. Flame should be as small as possible without going out. Note: Air mixture adjustment is not required on surface burners, 7.
-
Page 8: Model And Serial Number Location
Model and Serial Number Location For sealed bumer ovens, the identification plate is located on the right-hand surface of the oven front frame at the storage or warmer drawer; or the lower panel area. Waist-High Burner When ordering parts for or making inquires about your range, (Self Clean Models) always be sure to include the model and serial numbers and a lot number or letter from the identification...