Installation Instructions; Prepare Location - Jenn-Air JXW9030WP Installation Instructions And Use & Care Manual

Ifthehouse h as aluminum w iring, follow theprocedure
below:
1. Connect asection o fsolid copper wire tothepigtail
leads.
2. Connect thealuminum w iring totheadded section o f
copper wire using special connectors and/or tools
designed andULlisted forjoining c opper toaluminum.
Follow theelectrical connector manufacturer's recommended
procedure. Aluminum/copper connection must c onform with
local c odes a ndindustry a ccepted wiring practices.
• Wire sizes andconnections must c onform withtherating of
theappliance asspecified onthemodel/serial rating plate.
The model/serial plate islocated b ehind t hefilter ontherear
wall o ftherange h ood.
• Wire sizes must c onform totherequirements oftheNational
Electrical Code, ANSl/NFPA 70(latest edition), orCSA
Standards C22.1-94, Canadian Electrical Code, Part 1 and
C22.2 No. 0 -M91 (latest edition) and alllocal c odes a nd
ordinances.
INSTALLATION INSTRUCTIONS
• It is recommended that the vent system be installed before
hood is installed.
• If you are installing the optional backsplash with shelves for
heat lamps, follow the instructions included with that product.
• Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
• Check that all installation parts have been removed from the
shipping carton.
1. Disconnect power.
2. Determine which venting method to use: roof or wall exhaust.
3. Select a flat surface for assembling the range hood. Place
covering over that surface.
Excessive Weight Hazard
Use two or more people to move and install
range hood.
Failure to do so can result in back or other injury.
4. Using 2 or more people, lift range hood onto covered surface.
A. Wood support
B. Centerline
NOTE: The screws provided for mounting this hood must be
fastened into solid wood, do not fasten into sheet rock only.
Range Hood Mounting Screws Installation
The hood is attached to the wall with the wood support that is
attached to the back of the hood.
1. Determine and mark the centerline on the wall where the
canopy range hood will be installed.
2. Select a mounting height between a minimum of 30"
(76.2 cm) and a suggested maximum of 36" (91.4 cm), above
the cooking surface and the bottom of the range hood and
mark a horizontal reference line on the wall.
3. Remove the wood support from the back of the range hood
by loosening the 2 screws from the inside. Locate and level
the top of the wood support 153/8 '' (39.1 cm) above the
marked horizontal line and centered on the vertical centerline.
Using 2 - 4 of the 6 x 80 mm screws, install wood support so
that it is screwed into at least 2 vertical studs.
Optional Duct Cover Installation
1. Attach the full-width duct cover to the top of the range hood
with the screws provided with duct covers. The duct cover
must be attached to the top of the range hood before
mounting the range hood to the wall. For information on
ordering the optional duct cover, see "Accessories" section.
Complete Preparation
1. Determine and make all necessary cuts in the wall for the vent
system. Install the vent system before installing the range
hood. See the "Venting Requirements" section.
2. Determine the location where the power supply cable will be
run through the wall.
3. Drill a 1V4" (3.2 cm) hole at this location.
4. Pull enough power supply cable through the wall to allow for
easy connection to the terminal box.
5. Install the 10" (25.4 cm) square x 10" (25.4 cm) round vent
transition with damper to top of the range hood using
(4) - 3.5 x 9.5 mm screws.
6. Remove terminal box cover and set aside.
7. Remove knockout from the back of the vent hood and install
a UL listed or CSA approved 1/2"strain relief. See "Make
Electrical Connection" section.
8