Gas Supplu Requirements - GE Spacemaker DSXH47 Owner's Manual & Installation Instructions

Installation Instructions
EXHAUST DUCTING LENGTH
The exhaust s}_mm shouM be inspecled and cleaned a
lllil]illlill]l 01"evel)" year with normal usage. The moa th(
dlwer is used, the more ofi_n you should check tile exhausl
sx_mm and _nt hood tot prop( r operation.
• DO NOT assemble th( duct work with thstenep, that
extend into the duct. They will s(lve as coll_ ction points
fi:,r lint.
• Instflation - Ductwork which runs through an unheated
area or is near an air conditioning duct should be
insulat(d to rcdu(x condensation and lint buildup.
MAXIMUM LENGTH
of 4" (10.2cm) Dia. FLEXIBLE METALTUBING
PREFERREDVENT HOOD TYPE
4"(102cm) Louvered
Numbelturns _1 I
of 90°
I 2.5" I
4" (6.35
i]l,,q(lO.2cin)l-qlF- ---]l,,- ci,,) "_"
0 30" (9.14 m) 18' (5.49 m)
1 22" (6.71 m) 14' (4.27 m)
2 14' (4.27 m) 10' (3.05 m)
MAXIMUM LENGTH
of 4" (10.2cm)Dia. RIGIDMETALDUCT
PREFERRED VENT HOOD TYPE
4"(10,2cm) Louvered
Numbelturns _1 I
of90°
2.5" I
4,,
°"ll .... I (6.35
0 60" (18.28 m) 48' (14.63 m)
1 52" (15.84 m) 40' (12.19 m)
2 44' (13.41 m) 32' (9.75 m)
3 32' (9.75 m) 24' (7.31 m)
4 28' (8.53 m) 16" (4.87 m)
INSTALLMALE FITTINGS IN
CORRECT DIRECTION
EXHAUST DIRECTION
All (hyers m-e shipped set lip till real- exhmlsling.
On electric (Iwers, exhmlsfing can be on the cabinet right
or left ski(, or through tile (hyer bottom. ()as dlyers (nil
exhmlst on the (abinet right si(l( or the dlwer bouom. To
dmnge exhaust dire(don )ou will need Exhmlst Kit Pub.
No. I_A018 and a rigid metal 4" 90<legree elbow. The kit
is available through }our GE retailei: Follow the
instructions supplied with the kit.
Samo aS
/ _/other side EXHAUSTDUCTLOCATING
DIMENSIONS
fl'l 'l 57/_'
(15cm) 43/8'
3 3/4" (9.5cm)
GAS SUPPLY REQUIREMENTS
P.cpla(( hi'ass (Ollile(tiilg pipe that is llOt plastic-coated.
Stainless ste(l or l)lastic4"oated bl-<l_,s M UST be tlS((1.
WARNING:
,,l<l flexible
(OllIl('('tOl'% "I'ht"
use
ofoM flexible
COlllR>(lOiS (all ( _tl/qe
gas leaks and personal il!iuv,. Nways use NEW flexible
connectors when insmllillg a gas appliance.
1. Installation MUST confoml with local codes, or ill the
absence of local codes, with the National Fuel (;_s
Code, ANSI Z223.1 (lawst edition).
,
3.
The gas supply line should b( of 1/2" (1.27 cm)
rigid pip(.
If codes allow, tlexible metal tubing may be use(I
to connect your (hwer to the gas supply line. The
robing MUST be constructed of stainless st(el or
plastic-coamd bl-_lss.
4. The gas supply line MUST hay( an individual shutoff
xGIIv( .
5. A 1/8" (0.32 cm) NPI' plugged tal)ping, accessible tor
test gmlge c(mnection, MUST be installed immediately
upstr(am ot file gas supl)ly connection lo the dlyel:
6,
7.
Th_ dlTer MUST be disconnecled flom the gas supply
piping _)slem du ring any pressure testing of the gas
supply piping s}_tem at test pressurcs in (xcess of
1/2 psig (3.45 kPa).
Th( dryer MUST be isolated from the gas supply piping
sxstem during any pressure testing of the gas SUpl)ly
piping _?stem at It:st pressures ((lual to or kss than
1/2 psig (3.45 kPa).
13