If Problem Occurs - Sharp DK-KP80P Operation Manual

Troublshooting chart (continued)
■ Remote control
Symptom
● The remote control
does not operate.
■ Tuner
Symptom
● The radio makes
unusual noises
continuously.
■ USB
Symptom
● Device cannot be
detected.
● Playback does not
start.
● Wrong time display.
● Wrong file name
display.
■ iPod, iPhone or iPad
Symptom
● No sound is
produced.
● iPod, iPhone or iPad
will not charge.
● "This accessory is
not made to work
with iPhone" or
"This accessory is
not supported by
iPhone" appears on
iPhone screen.
Possible cause
● Is the AC power cord of the
unit plugged in?
● Is the battery polarity
correct?
● Is the battery dead?
● Is the distance or angle
incorrect?
● Does the remote control
sensor receive strong light?
Possible cause
● Is the unit placed near the
TV or computer?
● Is the FM antenna placed
properly? Move the antenna
away from the AC power
cord if it is located nearby.
Possible cause
● Is there any MP3/WMA file
available?
● Is the device properly
connected?
● Is it an MTP device?
● Does the device contain
AAC file only?
● Is it a copyright protected
WMA file?
● Is it a false MP3 file?
● Is Variable Bitrate file being
played back?
● Is the File Name written in
Chinese or Japanese
characters?
Possible cause
● The iPod, iPhone or iPad is
not playing.
● The iPod, iPhone or iPad is
not properly connected to the
unit.
● Is the AC power cord of the
unit plugged in?
● The iPod, iPhone or iPad is
not making full contact with
the connector.
● Using iPod (3 rd
generation).
● The iPod or iPhone is not
supported. Refer to page 4 for
compatible models.
● The iPhone battery is low.
Please charge the iPhone.
● iPhone is not properly
docked.
■ Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation
inside the cabinet (CD pickup, etc.) or on the transmitter on
the remote control. Condensation can cause the unit to
malfunction. If this happens, leave the power on with no
disc in the unit until normal playback is possible (about 1
hour). Wipe off any condensation on the transmitter with a
soft cloth before operating the unit.

■ If problem occurs

When this product is subjected to strong external
interference (mechanical
electricity, abnormal supply voltage due to lightning, etc.)
or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
1
Set the unit to the stand-by mode and turn the power on
again.
2
If the unit is not restored in the previous operation,
unplug and plug in the unit again, and then turn the
power on.
Note:
If neither operation above restores the unit, clear all the
memory by resetting it.
■ Factory reset, clearing all memory
1
Press the POWER ON/STAND-BY button to enter the
power stand-by mode.
2
While pressing down the OPEN/CLOSE button, press the
POWER ON/STAND-BY button until "Clear All" appears.
Caution:
This operation will erase all data stored in memory
including clock, timer settings and tuner preset.
■ Before transporting the unit
Remove the iPod, iPhone, iPad, USB memory device and disc
from the unit. Then, set the unit to the power stand-by mode.
Carrying the unit with iPod, iPhone, iPad or USB memory
device left connected or discs left inside might damage the unit.
■ Care of compact discs
Compact discs are fairly resistant to damage, however
mistracking can occur due to an accumulation of dirt on the
disc surface. Follow the guidelines below for maximum
enjoyment from your CD collection and player.
● Do not write on either side of the disc, particularly the
non-label side from which signals are read. Do not
mark this surface.
● Keep your discs away from direct sunlight, heat, and
excessive moisture.
● Always hold the CDs by the edges. Fingerprints, dirt, or
water on the CDs can cause noise or mistracking. If a CD
is dirty or does not play properly, clean it with a soft, dry
cloth, wiping straight out from the centre, along the radius.
NO
E-14
shock, excessive
POWER
YES
Correct
static