Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. ® This illustrations printed in this operation manual are for the model DK-A10.
SPECIAL NOTES DK-A10 DK-A10BK CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVIC- ING TO QUALIFIED SERVICE PERSONNEL. Explanation of Graphical Symbols: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage”...
IMPORTANT SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire.
IMPORTANT SAFETY INSTRUCTIONS (continued) DK-A10 DK-A10BK 18) Damage Requiring Service - Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions : a) When the AC cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following...
ENERGY STAR ® Program Information Products that have earned the ENERGY STAR designed to protect the environment through superior energy efficiency. ® To comply with the ENERGY STAR standards mentioned above, please cancel the demonstration mode, as described on page 10. ENERGY STAR ®...
Using this product with a higher voltage other than that which is specified is dangerous and may result in a fire or other type of accident causing damage. SHARP will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified.
System connections DK-A10 DK-A10BK Make sure to unplug the AC power cord before any connections. Antenna connection Supplied FM antenna: Connect the FM antenna wire to the FM 75 OHMS jack and position the FM antenna wire in the direction where the strongest signal can be received. Supplied AM loop antenna: Connect the AM loop antenna to the AM and GND terminals.
Remote control Battery installation This product contains a CR Coin Lithium Battery which contains Perchlorate Material – special handling may apply, California residents, see www.dtsc.ca.gov/hazardouswaste/perchlorate/ 1 While pushing the locking tab toward the center of the remote control, slide out the battery holder. Back of remote control Locking tab 2 Remove the old battery from the battery holder, insert the...
General control DK-A10 DK-A10BK FUNCTION CLOCK SLEEP FOLDER PLAY MODE TUNING CLEAR MEMORY To turn the power on Press the ON/STAND-BY button to turn the power on. After use: Press the ON/STAND-BY button to enter the power stand-by mode. Illumination light control Press the SNOOZE/DIMMER button to adjust the brightness of the display and LED.
Setting the clock In this example, the clock is set for the 12-hour (12:00 AM) display. Press the CLOCK button for more than 2 seconds. Press the button to select 12-hour or 24-hour display and then press the CLOCK button. “AM 12:00”...
Push the iPod sliding door iPod iPod（bottom） Dock connector iPod adaptor iPod dock iPod connector To remove iPod adaptor main unit (top) protection cover pull up push stopper iPod playback Press the ON/STAND-BY button to turn the power on. The iPod terminal door will automatically open when the display is on.
Listening to the iPod (continued) DK-A10 DK-A10BK Various iPod functions Function Main unit Remote control Play Pause Track up/ down Fast forward/ reverse Display ____ DISPLAY Repeat ____ PLAY MODE Random ____ PLAY MODE iPod operation Below operation can be done depend on iPod generation. Operation System on operation Press in the pause...
Listening to a CD or MP3/WMA disc This system can play back a standard CD, CD-R/RW in the CD format and CD-R/RW with MP3 or WMA ﬁles, but cannot record on them. Some audio CD-R and CD-RW discs may not be playable due to the state of the disc or the device that was used for recording.
Listening to a CD or MP3/WMA disc (continued) DK-A10 DK-A10BK Press the ON/STAND-BY button to turn the power on. Press the CD button. Insert the disc into the disc, label side up. Press the OPEN/CLOSE button to close the disc tray 1. [CD] Total number of Total playing...
Advanced CD or MP3/WMA disc playback Repeat play Repeat play can play all tracks on a disc or a programmed sequence continuously. To repeat play: Press the PLAY MODE button on the remote control. Press the button. To cancel repeat play: Press the PLAY MODE button again.
Advanced CD or MP3/WMA disc playback (continued) DK-A10 DK-A10BK Programmed play You can choose up to 32 selections for playback in the order you like. While in the stop mode, press the MEMORY button to enter the programming save mode. Press the button to select the desired track.
MP3/WMA folder mode (only for MP3/WMA ﬁles) To playback MP3/WMA (Windows Media Audio) ﬁle There are many music sites on the internet that you can download MP3/WMA (Windows Media Audio) music ﬁles. Follow the instructions from the website on how to download the music files. You can then playback these downloaded music files by burning them to a CD-R/RW disc.
MP3/WMA folder mode (only for MP3/WMA ﬁles) (continued) DK-A10 DK-A10BK Procedure to playback MP3/WMA disc To playback CD-R/RW. Press the CD button, and load a MP3/WMA disc. After disc is loaded, disc info will be displayed. MP3 indicator WMA indicator In case folder is selected, proceed to step 2.
Listening to the radio SNOOZE/ FUNCTION CLOCK DIMMER SLEEP ALARM FOLDER DISPLAY PLAY E SOUND MODE /DEMO TUNING CLEAR MEMORY Auto power on function: When you press any of the following buttons, the unit turns on. TUNER button (main unit): The unit turns on and the TUNER function is activated.
Listening to the radio (continued) DK-A10 DK-A10BK Memorizing a station You can store 40 AM and FM stations in memory and recall them at the push of a button. (Preset tuning) Perform steps 1 - 3 in “Tuning” on page 23. Press the MEMORY button to enter the preset tuning saving mode.
Alarm and sleep operation Alarm The unit turns on and play desired source (iPod, CD, TUNER, AUX) or Buzzer sound for 30 minutes. Before setting the alarm: 1 Check that the clock is set to the correct time (refer page 13). If it is not set, you cannot use the alarm function.
Alarm and sleep operation (continued) DK-A10 DK-A10BK Sleep operation The radio and iPod can be turned off automatically. Play back the desired sound source. Press the SLEEP button to select sleep time. Press the MEMORY button. “SLEEP” will appear. The unit will enter the power stand-by mode automatically after the preset time has elapsed.
Enhancing your system The connection cord is not included. Purchase a commercially available cord as shown below. VCR, DVD, etc. To the line output jacks White RCA cord (not supplied) Auto power on function: When you press any of the following buttons, the unit turns on. AUX button (main unit): The unit turns on and the AUX function is activated.
Many potential problems can be resolved by the owner without calling a service technician. If something is wrong with this product, check the following before calling your authorized SHARP dealer or service center. General Symptom The clock is not set to Is the ST switch set to the correct the correct time.
Do not apply oil to the inside of the unit. It may cause malfunctions. Specifications As part of our policy of continuous improvement, SHARP reserves the right to make design and speciﬁcation changes for product improvement without prior notice. The performance speciﬁcation ﬁgures indicated are nominal values of production units.
Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer.