Download  Print this page

Timer And Sleep Operation (Remote Control Only) - Sharp DK-KP80P Operation Manual

Slim micro system
Hide thumbs

Advertisement

Table of Contents

Timer and sleep operation (Remote control only)

Timer playback:
The unit turns on and plays the desired source (CD,
TUNER, USB, iPod, AUDIO IN) at a preset time.
This unit has 2 types of timer: ONCE TIMER and DAILY
TIMER.
Once timer (" " indicator):
Once timer play works for one time only at a preset time.
Daily timer ("DAILY" indicator):
Daily timer play works at the same preset time every day
that we set. For example, set the timer as a wake-up call
every morning.
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio program,
and use the daily timer to wake up.
1
Set the daily timer.
2
Set the once timer.
1 minute or more
Daily timer
Stop
Start
■ Timer playback
Before setting timer:
● Check that the clock is set to the correct time (refer to
page 11). If it is not set, you cannot use the timer
function.
● For timer playback: Plug in USB or load discs or dock
iPod to be played.
1
Press the POWER ON/STAND-BY button to turn the power on.
2
Press and hold the CLOCK/TIMER button.
3
Within 10 seconds, press the
select "Once" or "Daily", and press the ENTER button.
4
Within 10 seconds, press the
select "Timer Set", and press the ENTER button.
5
To select the timer playback source (CD, TUNER, USB,
iPod, AUDIO IN), press the
the ENTER button.
When you select the tuner, select a station by pressing
the
or
button, and then press the ENTER
button. If a station has not been programmed, "No
Preset" will be displayed and timer setting will be
canceled.
6
To adjust the day, press the
press the ENTER button.
7
Press the ENTER button to adjust the hour. Press the
or
button and then press the ENTER button.
8
To adjust the minutes, press the
then press the ENTER button.
9
Set the time to finish as in steps 7 and 8 above.
10
Adjust the volume using the VOLUME control, and then
press the ENTER button. Do not turn the volume up too
high.
11
Press the POWER ON/STAND-BY button to enter the
power stand-by mode. The "TIMER" indicator lights up
and the unit is ready for timer playback.
Once timer
Start
Stop
or
button to
or
button to
or
button. Press
or
button and then
or
button and
E-12
12
When the preset time is reached, playback will start.
The volume will increase gradually until it reaches the
preset volume. The timer indicator will blink during
timer playback.
13
When the timer end time is reached, the system will
enter the power stand-by mode automatically.
Once timer:
The timer will be canceled.
Daily timer:
The timer operates at the same time every selected day.
It will continue until the daily timer setting is canceled.
Cancel the daily timer when it is not in use.
Notes:
● When performing timer playback using another unit
connected to the USB terminal or AUDIO IN jack, select
"USB" or "AUDIO IN" in step 5.
● This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn
on or off. To stop the timer playback, follow step
"Cancelling the timer setting" of this page.
Checking the timer setting:
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
2
Within 10 seconds, press the
"Once" or "Daily", and press the ENTER button.
3
Within 10 seconds, press the
"Timer Call", and press the ENTER button.
Cancelling the timer setting:
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
2
Within 10 seconds, press the
"Once" or "Daily", and press the ENTER button.
3
Within 10 seconds, press the
"Timer Off", and press the ENTER button. Timer will be
canceled (the setting will not be canceled).
Reusing the memorised timer setting:
The timer setting will be memorised once it is entered. To
reuse the same setting, perform the following operations.
1
Turn the power on and press and hold down the
CLOCK/TIMER button.
2
Within 10 seconds, press the
"Once" or "Daily", and press the ENTER button.
3
Within 10 seconds, press the
"Timer On" , and press the ENTER button.
4
Press the POWER ON/STAND-BY button to enter the
power stand-by mode.
or
button to select
or
button to select
or
button to select
or
button to select
or
button to select
or
button to select

Advertisement

Table of Contents
loading

  Related Manuals for Sharp DK-KP80P