Page 1: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 3: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....8 Roll Over Warning .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION handles on different road surfaces. Your driving skills Thank you for selecting a Jeep Commander and wel- will improve with experience. When driving off-road or come to our worldwide family. working the vehicle, don’t overload it or expect it to overcome the laws of nature.
Page 5 INTRODUCTION 5 Do not attempt sharp turns or abrupt maneuvers or other Failure to use driver and passenger seat belts provided unsafe driving actions that can cause loss of vehicle is a major cause of severe or fatal injury. In fact, the U.S. control.
Page 6: How To Use This Manual
6 INTRODUCTION NOTE: After you read the manual, it should be stored HOW TO USE THIS MANUAL in the vehicle for convenient reference and remain with Consult the table of contents to determine which section the vehicle when sold so that the new owner will be contains the information you desire.
Page 7 INTRODUCTION 7...
Page 8: Warnings And Cautions
8 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 9: Vehicle Modifications / Alterations
INTRODUCTION 9 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....14 To Set The Alarm ..... .18 Ignition Key Removal .
Page 12 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Service ....24 Lap/Shoulder Belts .....38 Remote Starting System —...
Page 13: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Exhaust Gas ......68 Safety Checks You Should Make Outside The Vehicle .
Page 14: A Word About Your Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The keys for your new vehicle are enclosed in a plastic Place the shift lever in P (Park). Turn the ignition switch bag with the key code number on it. If you received your to the OFF position, and remove the key.
Page 15: Key-In-Ignition Reminder
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Key-In-Ignition Reminder WARNING! If the driver’s door is opened when the key is in the ignition and not turned to the ON position, a chime will Leaving children in a vehicle unattended is danger- sound to remind you to remove the key.
Page 16: Important Note About Service
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE light will come on for 3 seconds immediately after the with remote starting systems. Use of these systems ignition switch is turned on for a bulb check. Afterwards, may result in vehicle starting problems and loss of if the bulb remains on, this indicates a malfunction in the security protection.
Page 17: Replacement Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Replacement Keys Customer Key Programming NOTE: Only keys that have been programmed to the You can program new keys to the system if you have two vehicle electronics can be used to start the vehicle. Once valid keys by doing the following: a Sentry Key has been programmed to a vehicle, it cannot 1.
Page 18: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and SECURITY ALARM SYSTEM — IF EQUIPPED turn the ignition switch ON within 60 seconds. After 10 This system monitors the vehicle doors, liftgate, liftgate seconds, a single chime will sound.
Page 19: To Disarm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 the door lock plunger located on the inside of the doors the system. The Security Alarm System will not disarm or with the driver’s door key lock cylinder, will not set with a manual unlock, either through the lock plunger the alarm.
Page 20 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work. If the vehicle is shifted out of P (Park), all the transmitter buttons are disabled for all keys.
Page 21: To Unlock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: If desired, the system can be programmed to unlock all doors on the first press of the “Unlock” button. Refer to “Remote Unlock Driver’s Door 1st” in the Personal Settings section of the “Electronic Vehicle Infor- mation Center (EVIC)”, or simply follow these steps: 1.
Page 22: To Release The Liftgate Flipper Glass
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Customer Programmable Features of the “Electronic Ve- WARNING! hicle Information Center (EVIC)” section or by following these steps. Driving with the flipper glass open can allow poi- sonous exhaust gases into your vehicle. You and your 1.
Page 23: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 NOTE: The interior lights will turn off when the ignition The “Flash Lights On Lock/Unlock” feature can be is switched to the ACC or ON position after the panic reactivated by repeating this procedure. alarm is activated.
Page 24: Transmitter Battery Service
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Service The recommended replacement battery is one CR2032 battery. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. 1. With the transmitter buttons facing down, remove the small screw, and separate the two halves of the transmit- ter.
Page 25: Remote Starting System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 3. To reassemble the transmitter case, join the two halves of the case together. Install and tighten the screw until snug. Make sure there is an even “gap” between the two halves. Test transmitter operation. REMOTE STARTING SYSTEM —...
Page 26: Door Locks
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE unlocked, you have 60 seconds to enter the vehicle, insert DOOR LOCKS the key into the ignition, and move it to the RUN Manual Door Locks position. Otherwise, the engine will cancel remote start Use the manual door lock plunger to lock the doors from and automatically turn off.
Page 27: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 If you press the door lock switch while the keys are in the Power Door Locks — If Equipped A door lock switch is on each front door panel. Press this ignition switch, and the driver’s door is open, the doors switch to lock or unlock the doors.
Page 28: Child Protection Door Lock
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Unlock on Exit Feature — Only WARNING! Available if Auto Lock is Enabled This feature will unlock all the doors when the driver’s Avoid trapping anyone in the vehicle in a collision. door is opened if the vehicle is stopped and in P (Park) or Remember that the rear doors can only be opened from N (Neutral).
Page 29: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down Auto Up Feature with Anti-Pinch Protection Both the driver and front passenger window switch has (Driver’s and Front Passenger Door Only) an “Auto Down” feature. Press the window switch past Lift the window switch to the second detent, release, and the first detent, release, and the window will go down the window will go up automatically.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset.
Page 32: Wind Buffeting
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 33: Liftgate Flipper Glass
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked.
Page 34: Power Liftgate - If Equipped
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once the liftgate flipper glass has been opened, connec- liftgate is fully open, pressing the button twice within tion to the rear window wiper is interrupted, preventing five seconds a second time will close the liftgate. activation of the rear wiper blade while the flipper glass is open.
Page 35 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 closing or opening, the liftgate will automatically NOTE: • In the event of a power malfunction to the liftgate, an reverse to the closed or open position, provided it emergency liftgate latch release can be used to open meets sufficient resistance.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The power liftgate buttons will not operate if the WARNING! vehicle is in gear or the vehicle speed is above 0 mph • Driving with the liftgate open can allow poison- (0 km/h).
Page 37: Occupant Restraints
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 OCCUPANT RESTRAINTS WARNING! Some of the most important safety features in your vehicle are the restraint systems. These include the front In a collision, you and your passengers can suffer and rear seat belts for the driver and all passengers, front injuries, including fatalities, if you are not properly airbags for both the driver and right front passenger, and, buckled up.
Page 38: Lap/Shoulder Belts
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they WARNING! can reduce the seriousness of injuries in a collision. Some • Wearing a seat belt incorrectly is dangerous. Seat of the worst injuries happen when people are thrown from the vehicle.
Page 39: Lap/Shoulder Belt Operating Instructions
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of your seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to make the belt go around your lap.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” A belt that is buckled into the wrong buckle will not protect you properly.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 4. Position the lap belt across your thighs, below your 5. Position the shoulder belt on your chest so that it is abdomen. To remove slack in the lap portion, pull up a comfortable and not resting on your neck.
Page 42: Adjustable Upper Shoulder Belt Anchorage
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button marked PRESS Adjustable Upper Shoulder Belt Anchorage on the buckle. The belt will automatically retract to its In the front seating positions, the shoulder belt can be stowed position.
Page 43: Automatic Locking Mode - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 As a guide, if you are shorter than average, you will 2. Grasp the shoulder portion and pull downward until prefer a lower position, and if you are taller than average, the entire belt is extracted. you’ll prefer a higher position.
Page 44: Seat Belt Pretensioners
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This safety belt system has a retractor assembly that is Seat Belt Pretensioners designed to release webbing in a controlled manner. This The driver and front passenger seat belts are equipped feature is designed to help reduce the belt force acting on with a pretensioning device that is designed to remove the occupant’s chest.
Page 45: Seat Belts And Pregnant Women
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 Seat Belts and Pregnant Women WARNING! We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is Using a seat belt extender when not needed can the best way to keep the baby safe.
Page 46: Driver And Front Passenger Supplemental Restraint Systems (Srs)
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Driver And Front Passenger Supplemental This vehicle has airbags for both the driver and right Restraint Systems (SRS) front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 This vehicle is equipped with window bags to protect the WARNING! driver, front, and rear passengers sitting next to a win- • dow. They are located above the side windows. Their Do not put anything on or around the front airbag covers are also labeled SRS/AIRBAG.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: Do not use a clothing bar mounted to the coat The window bag on the crash side of the vehicle is hooks in this vehicle. A clothing bar will impede the triggered in moderate to severe side collisions.
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Children that are not big enough to properly wear the 3. The driver and front passenger seats should be moved vehicle seat belt should be secured in the rear seat, in a back as far as practical to allow the front airbags room to child restraint or belt-positioning booster seat.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components WARNING! The airbag system consists of the following: • Relying on the airbags alone could lead to more • Occupant Restraint Control Module severe injuries in a collision. The airbags work •...
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Also, the ORC turns on the “Airbag Warning How The Airbag System Works Light” for 6 to 8 seconds for a self-check • The Occupant Restraint Control (ORC) Module de- when the ignition is first turned on. After the termines if a frontal, side, or rollover collision is severe self-check, the “Airbag Warning Light”...
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Driver and Passenger Airbag/Inflator Units are • The Side Impact SRS Side Curtain Airbags are de- located in the center of the steering wheel and the right signed to activate only in certain side or rollover side of the instrument panel.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 They are not permanent and normally heal quickly. If A Deployment Occurs The airbag system is designed to deploy when the However, if you haven’t healed significantly within a Occupant Restraint Control (ORC) Module detects a few days, or if you have any blistering, see your doctor moderate-to-severe frontal collision, to help restrain the immediately.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, • Modifications to any part of the airbag system seat belt pretensioners, and seat belt retractor assem- could cause it to fail when you need it.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 with other data gathered during a complete accident Airbag Warning Light You will want to have the airbag system ready to inflate investigation, the electronic data may be used by for your protection in an impact. The airbag system is DaimlerChrysler Corporation and others to learn more designed to be maintenance free.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provided to the custodial entity upon request. General Data Parameters that May Be Recorded: data that does not identify particular vehicles or crashes • Diagnostic trouble code(s) and warning lamp status may be released for incorporation in aggregate crash for electronically-controlled safety systems, including databases, such as those maintained by the US govern- the airbag system...
Page 57: Child Restraint
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 Child Restraint WARNING! Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United In a collision, an unrestrained child, even a tiny States and all Canadian provinces require that small baby, can become a missile inside the vehicle.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The infant carrier is only used rearward-facing in the WARNING! vehicle. It is recommended for children who weigh up • Improper installation can lead to failure of an to about 20 lbs (9 kg). “Convertible” child seats often have a higher weight limit in the rearward-facing infant or child restraint.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 Standards. The manufacturer also recommends that belt tight, however, any seat belt system will loosen you try a child restraint in the vehicle seats where you with time, so check the belt occasionally and pull it will use it before you buy it.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still cannot be tightened, or if pulling and Older Children and Child Restraints pushing on the restraint loosens the belt, disconnect Children who weigh more than 20 lbs (9 kg) and who are the latch plate from the buckle, turn the buckle older than one year can ride forward-facing in the around, and insert the latch plate into the buckle...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Children Too Large for Booster Seats LATCH — Child Seat Anchorage System (Lower Children who are large enough to wear the shoulder belt Anchors and Tether for CH ildren) comfortably, and whose legs are long enough to bend Your vehicle’s second row seat is equipped with the child over the front of the seat when their back is against the restraint anchorage system called LATCH.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE kits or retro-fit kits. You are urged to take advantage of all The second row outboard seating positions have lower the available attachments provided with your child re- anchorages that are capable of accommodating LATCH- straint in any vehicle.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here. Again, carefully follow the installation instructions that were provided with the child restraint system.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In addition, there are tether strap anchorages behind each means of adjusting the tension in the strap. Forward- rear outboard seating position located on the back of the facing toddler restraints and some rear-facing infant seat.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 If the seat belt has a automatic locking retractor, it will WARNING! have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the Improper installation of a child restraint to the child restraint and slide the latch plate into the buckle.
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE to do something more. Disconnect the latch plate from Route the tether strap over the seat back and attach the the buckle, turn the buckle around, and insert the latch hook to the tether anchor located on the back of the seat. plate into the buckle again.
Page 67: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 The engine oil installed in the engine at the factory is a Transporting Pets Airbags deploying in the front seat could harm your pet. high quality energy conserving type lubricant. Oil An unrestrained pet will be thrown about and possibly changes should be consistent with anticipated climate injured, or injure a passenger during panic braking or in conditions under which vehicle operations will occur.
Page 68: Safety Tips
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SAFETY TIPS stopped in an open area with engine running for more than a short period, adjust the ventilation system to Exhaust Gas force fresh, outside air into the vehicle. • Guard against carbon monoxide with proper mainte- WARNING! nance.
Page 69: Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Safety Checks You Should Make Inside The Airbag Warning Light Vehicle The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first Seat Belts turned on.
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Outside The Lights Vehicle Have someone observe the operation of all exterior lights while you work the controls. Check turn signal and high Tires beam indicator lights on the instrument panel. Examine tires for excessive tread wear or uneven wear patterns.
Page 71: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......76 Heated Remote Control Mirrors — If Equipped .
Page 72 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Things You Should Know About Your Setting Memory Positions And Linking Remote UConnect™ System .....97 Keyless Entry Transmitter To Memory .
Page 73 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Daytime Running Lights — If Equipped ..123 Tilt Steering Column ....130 Lights-On Reminder .
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE BAS (Brake Assist System) ....136 Turning The Rear Camera Off ... . 150 ERM (Electronic Roll Mitigation) .
Page 75 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 Pinch Protect Override ....160 Power Outlet ......162 Venting Sunroof - Express .
Page 76: Mirrors
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS A two-point pivot system allows for horizontal and vertical adjustment of the mirror. Inside Day/Night Mirror The mirror should be adjusted to center on the view Annoying headlight glare from vehicles behind you can through the rear window.
Page 77: Automatic Dimming Mirror - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Automatic Dimming Mirror — If Equipped CAUTION! This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature To avoid damage to the mirror during cleaning, on or off by pressing the button at the base of the mirror. never spray any cleaning solution directly onto the A light next to the button will indicate when the dimming mirror.
Page 78: Exterior Mirrors Folding Feature
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Outside Automatic Dimming Mirror — If WARNING! Equipped If your vehicle is equipped with a driver’s outside Vehicles and other objects seen in the passenger side automatic dimming mirror, it operates when the inside convex mirror will look smaller and farther away automatic dimming mirror is on.
Page 79: Heated Remote Control Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 After selecting a mirror move the knob in the same Power mirror preselected positions can be controlled by direction you want the mirror to move. Use the center off the optional Memory Seat Feature. Refer to “Driver position to guard against accidentally moving a mirror Memory Seat”...
Page 80: Hands-Free Communication (Uconnect™) - If Equipped
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Lift the cover to reveal the mirror. The light will turn on HANDS–FREE COMMUNICATION (UConnect™) — automatically. IF EQUIPPED UConnect™ is a voice-activated, hands-free, in- vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone using simple voice commands (e.g., Call”...
Page 81 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 The UConnect™ phonebook enables you to store up to 32 names and four numbers per name. Each language has a separate 32-name phonebook accessible only in that language. This system is driven through your Blue- tooth™...
Page 82: Operations
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for Headset Profile), you may not be able to use any UCon- nect™ features. Refer to your cellular service provider or the voice on beep, which follows the Ready prompt the phone manufacturer for details.
Page 83 At any prompt, after the voice on beep, you can say NOTE: • www.chrysler.com/uconnect Cancel and you will be returned to the main menu. However, in a few instances the system will take you • www.dodge.com/uconnect back to the previous menu. • www.jeep.com/uconnect...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked to give your cellular phone a The following are general phone to UConnect™ System pairing instructions: priority level between 1 and 7, 1 being the highest priority. You can pair up to seven cellular phones to •...
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 • System will prompt you to say the number you want you can say John Doe, where John Doe is a previ- call. ously stored name entry in the UConnect™ phone- book. Refer to Add Names to Your UConnect™ •...
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, say the name of the new entry. Use of four associated phone numbers and designations. Each long names helps the voice recognition and is recom- language has a separate 32-name phonebook accessible mended.
Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 • After you enter the Phonebook Delete menu, you will After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry then be asked for the name of the entry that you wish in the phonebook, call the number you just edited, or to delete.
Page 88: Phone Call Features
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • To call one of the names in the list, press the Voice Delete All Entries in the UConnect™ Phonebook Recognition’ button during the playing of the desired • Press the ’Phone’ button to begin. name, and then say Call.
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Answer or Reject an Incoming Call - No Call Making a Second Call while Current Call in Currently in Progress Progress When you receive a call on your cellular phone, the To make a second call while you are currently in a call, UConnect™...
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Toggling Between Calls established, press and hold the ’Phone’ button until you If two calls are in progress (one active and one on hold), hear a double beep indicating that the two calls have press the ’Phone’...
Page 91: Uconnect™ System Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Call Continuation UConnect™ System Features Call continuation is progression of a phone call on Language Selection UConnect™ system after the vehicle ignition key has To change the language that the UConnect™ system is been switched to off.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Emergency Assistance The UConnect™ system does slightly lower your chances If you are in an emergency and the mobile phone is of successfully making a phone call as to that for the cell reachable: phone directly.
Page 93 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Please refer to the 24-Hour “Towing Assistance” cover- You can use your UConnect™ system to access a voice- age details in the Warranty information booklet and on mail system or an automated service, such as, paging the 24–Hour Towing Assistance Card.
Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Barge In - Overriding Prompts Phone and Network Status Indicators The ’Voice Recognition’ button can be used when you If available on the radio and/or on a premium display wish to skip part of a prompt and issue your voice such as the instrument panel cluster, and supported by recognition command immediately.
Page 95: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • After the Ready prompt and the following beep, say NOTE: Certain brands of mobile phones do not send the dial ring to the UConnect™ system to play it on the Mute-off. vehicle audio system, so you will not hear it. Under this Information Service situation, after successfully dialing a number, the user When using AT&T Wireless Service, dialing to phone...
Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will play the phone names of Connect or Disconnect Link Between the UConnect™ System and Cellular Phone all paired cellular phones in order from the highest to Your cellular phone can be paired with many different the lowest priority.
Page 97: Things You Should Know About Your Uconnect™ System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 • You can also press the Voice Recognition’ button • You can also press the Voice Recognition’ button anytime while the list is being played, and then choose anytime while the list is being played and then choose the phone that you wish to select.
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance is maximized under: • It is not recommended to store similar sounding names in the UConnect™ phonebook. • low-to-medium blower setting, • UConnect™ phonebook nametag recognition rate is • low-to-medium vehicle speed, optimized for the voice of the person who stored the •...
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • smooth road surface, Bluetooth Communication Link Occasionally, Cellular phones have been found to lose • fully closed windows, and connection to the UConnect™ system. When this hap- • dry weather condition. pens, the connection can generally be re-established by switching the phone off/on.
Page 100 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101...
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 103: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 SEATS North American English Primary Alternate(s) Front Manual Seat Adjustment Move the seat forward or rearward using the adjustment Zero bar. Lift up on the bar located on the front of the seat near Add location Add new the floor.
Page 104: Front Seat Adjustment - Recline
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline WARNING! To adjust the seatback, lift the lever located on the • It is extremely dangerous to ride in a cargo area, outboard side of the seat, lean back, and release the lever at the desired position.
Page 105: Manual Lumbar Support Adjustment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Manual Lumbar Support Adjustment 8 - Way Driver’s Power Seat The manual lumbar support adjustment lever is located The driver’s power seat switches are located on the on the right side of the driver’s seat and on the left side outboard side of the driver’s seat lower side trim.
Page 106: Way Passenger's Power Seat - If Equipped
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjust- ment.
Page 107 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 center of the instrument panel. After turning on the Pressing the switch a second time will select low-level ignition, you can choose from High, Off, or Low heat heating. Pressing the switch a third time will shut the settings.
Page 108: 40/20/40 Second Row Folding Seat
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Pull up on the seatback lever located on the outboard WARNING! side of the seat. Persons who are unable to feel pain to the skin NOTE: Also, pulling upward on this handle allows the because of advanced age, chronic illness, diabetes, outboard seating positions to be reclined.
Page 109 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 WARNING! Do not drive the vehicle with the outer second row seats in the tumbled position. The outer second row seats are only intended to be tumbled for entry and exit to the third row seat. Failure to follow these instructions could result in personal injury.
Page 110 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If sitting in the third row seat, pull rearward on Folding Middle Seatback (Second Row Seat) the release strap located at the rear of the seat and tumble 1. Pull the release strap. the seat forward.
Page 111: 50/50 Third Row Folding Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 2. Lower the center seatback. Armrest (Second Row Seat) 50/50 Third Row Folding Seat Folding Center Seatback Center Seat Armrest (Second Row Seat) — If To Lower Rear Seat Equipped Either side of the third row seat can be lowered to allow The second row center seat may be equipped with a for extended cargo space, and still maintain some rear armrest.
Page 112 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Open the tailgate. To Raise Rear Seat 2. Push the seatback release handle (toward rear of 1. Open the tailgate. vehicle), and lower the seatback using the pull strap. 2. Detach pull strap from back of seat, and pull seatback upward until it locks into place.
Page 113: Driver Memory Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 4. Close the tailgate. WARNING! The cargo area in the rear of the vehicle (with the rear seatbacks in the locked-up or folded down position) should not be used as a play area by children when the vehicle is in motion.
Page 114: Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Setting Memory Positions and Linking Remote 5. Turn on the radio and set the radio station presets (up Keyless Entry Transmitter to Memory to 10 AM and 10 FM stations can be set). NOTE: Each time the SET (S) button and a numbered 6.
Page 115: Memory Position Recall
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 11. Select Remote Linked to Memory in the Electronic To recall the memory settings for driver one, press Vehicle Information Center (EVIC) and enter Yes or memory button number 1 on the driver’s door or the select Use Factory Settings from the EVIC and enter “Unlock”...
Page 116: To Disable A Transmitter Linked To Memory
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Disable A Transmitter Linked to Memory NOTE: Once programmed, all transmitters linked to memory can be easily enabled or disabled at one time. 1. Turn the ignition switch to the OFF position and Refer to Remote Linked to Memory under Electronic remove the key.
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • The seat shall move to the position located 0.3 inches Each stored memory setting will have an associated Easy (8 mm) forward of the rear stop if the starting position Entry and Easy Exit position. is between 0.9 inches to 2.67 inches (23 mm to 68 mm) NOTE: The Easy Entry Easy Exit feature is not enabled forward of the rear stop when the key is removed from...
Page 118: To Open And Close The Hood
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO OPEN AND CLOSE THE HOOD Then, reach under the hood, move safety latch to the left, To open the hood, pull the release lever inside your and lift the hood. To prevent possible damage, do not vehicle located below the instrument panel and in front slam the hood to close it.
Page 119: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 LIGHTS WARNING! Multi-Function Control Lever If the hood is not fully latched, it could fly up when The multi-function control lever controls the operation of the vehicle is moving and block your forward vision. the headlights, turn signals, headlight beam selection, Be sure all hood latches are fully latched before instrument panel light dimming, passing light, interior...
Page 120: Lights
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Battery Saver Feature—Exterior/Interior Lights If the multi-function control lever is left in the interior light position, parking light position, or the headlight position when the ignition switch is moved to the OFF position, the battery saver feature will automatically turn off the exterior and interior lights after eight minutes.
Page 121: Smartbeams - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 This system performs two functions. With the engine When your headlights come on during the NOTE: running and the multi-function control lever in the A daytime, the instrument panel lights will automatically (Auto) position, the headlights will turn on and off based dim to the lower nighttime intensity.
Page 122: Instrument Panel And Interior Lights
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Activate headlights to remain on longer (closer to the vehicle). Also, dirt, film, and other obstructions (sticker, toll box, 1. Select “Auto Headlamp Low/High Beams? — Low/ etc.) on the windshield or camera lens will cause the High Beam.”...
Page 123: Daytime Running Lights - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 “Off” position the instrument panel lighting is at the Fog Lights — If Equipped lowest light level and may not be suitable for night The fog light switch is located in the multi- driving.
Page 124: Turn Signals
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals Passing Light Move the multi-function control lever up or down and You can signal another vehicle with your headlights by the arrows on each side of the instrument cluster will lightly pulling the multi-function control lever toward flash to show proper operation of the front and rear turn the steering wheel.
Page 125: Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Interior Lights The interior lighting consists of courtesy lights mounted below the instrument panel, an overhead console light assembly which contains both driver and passenger reading lights, reading lights located above the rear doors, and a rear cargo light.
Page 126: Windshield Wipers And Washers
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS The front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select “Lo,” “Hi,” or one of the five speed sensitive intermittent windshield wiper speeds.
Page 127: Mist
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 To use the washer, pull the lever toward you and hold Mist while spray is desired. If the lever is pulled while in the Use this feature when weather conditions make occa- delay range, the wiper will operate for several seconds sional usage of the wipers necessary.
Page 128: Rain Sensing Wipers-If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rain Sensing Wipers—If Equipped The sensitivity of the system can be adjusted with the This feature senses moisture on the windshield and multi-function lever. Wiper delay position 1 is the least automatically activates the wipers for the driver. The sensitive, and wiper delay position 5 is the most sensi- feature is especially useful for road splash or overspray tive.
Page 129 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 • A customer programmable feature in the Electronic • Transmission in N (Neutral) Position — When the Vehicle Information Center (EVIC) allows the Rain ignition is ON, and the transmission is in the N Sense feature to be turned off.
Page 130: Tilt Steering Column
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN WARNING! To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as Tilting the steering wheel column while the vehicle desired.
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 • The pedals can be adjusted while driving. • The pedals cannot be adjusted when the vehicle is in R (Reverse) or when the Speed Control is ON. A message will be displayed in the Electronic Vehicle Information Center (EVIC) if the pedals are attempted to be ad- justed when the system is locked out (“Adjustable Pedal Disabled —...
Page 132: Electronic Speed Control
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL To Activate When engaged, this device takes over accelerator opera- Press the ON·OFF button to turn the system ON. To turn tions at speeds greater than 25 mph (40 km/h) for 5.7L the system OFF, press the ON·OFF button again.
Page 133: To Resume Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 To decrease speed while Speed Control is ON and SET, To Resume Speed To resume a previously set speed, press and release the press and hold the DECEL button. Release the button RES·ACCEL button. Resume can be used at any speed when the desired speed is reached, and the new speed above 25 mph (40 km/h) for 5.7L engines, and 30 mph (48 will be set.
Page 134: Driving Up Or Down Hills
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE to lock out overdrive. Press the TOW/HAUL switch on vehicle to gain speed, press the brake pedal, which will the lower center switch bank (below the Heating/Air disengage the Speed Control and help slow your vehicle. Conditioning controls).
Page 135: Electronic Brake Control System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 ELECTRONIC BRAKE CONTROL SYSTEM WARNING! Your vehicle is equipped with an advanced electronic brake control system that includes ABS (Anti-Lock Brake ABS (Anti-Lock Brake System) cannot prevent the System), TCS (Traction Control System), BAS (Brake natural laws of physics from acting on the vehicle, Assist System), ERM (Electronic Roll Mitigation), and nor can it increase the traction afforded by prevail-...
Page 136: Tcs (Traction Control System)
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TCS (Traction Control System) BAS (Brake Assist System) The BAS is designed to optimize the vehicle’s braking This system monitors the amount of wheel spin of each of capability during emergency braking maneuvers. The the driven wheels.
Page 137: Erm (Electronic Roll Mitigation)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 ERM (Electronic Roll Mitigation) WARNING! This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the BAS (Brake Assist System) cannot prevent the natu- speed of the vehicle. When ERM determines that the rate ral laws of physics from acting on the vehicle, nor of change of the steering wheel angle and vehicles speed can it increase the traction afforded by prevailing...
Page 138: Esp (Electronic Stability Program)
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Anytime the ESP system is in the “Full Off” ESP (Electronic Stability Program) mode, ERM is disabled. Refer to ESP (Electronic Stability This system enhances directional control and stability of Program) for a complete explanation of the available ESP the vehicle under various driving conditions.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 • Understeer - when the vehicle is turning less than WARNING! appropriate for the steering wheel position. ESP (Electronic Stability Program) cannot prevent The ESP/TCS Indicator Light located in the instrument the natural laws of physics from acting on the cluster, starts to flash as soon as the tires lose traction and vehicle, nor can it increase the traction afforded by the ESP system becomes active.
Page 140 140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE High Range (4WD Models) or 2WD Models or gravel conditions and more wheel spin than ESP would normally allow is required to gain traction. To turn ESP on again, momentarily depress the ESP Control This is the normal operating mode for ESP in 4WD high Switch .
Page 141 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 NOTE: To improve the vehicle’s traction when driving In this mode, ESP and TCS, except for the “limited slip” with snow chains, or starting off in deep snow, sand, or feature described in the TCS section, are turned off until gravel, it may be desirable to switch to the “Partial Off”...
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40 mph (64 km/h). At 40 mph (64 km/h), the normal ESP WARNING! stability function returns but TCS remains off. When the vehicle speed drops below 35 mph (56 km/h), the ESP With the ESP switched off, the enhanced vehicle system shuts off.
Page 143: Esp/Bas Warning Lamp And Esp/Tcs Indicator Light
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 If the “ESP/BAS Warning Lamp” comes on WARNING! continuously with the engine running, a mal- function has been detected in either the ESP or With the ESP switched off, the enhanced vehicle the BAS system, or both. If this light remains on stability offered by ESP and ERM are unavailable.
Page 144: Rear Park Assist System- If Equipped
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR PARK ASSIST SYSTEM— IF EQUIPPED Rear Park Assist Sensors The Rear Park Assist System provides visual and audible The four Rear Park Assist Sensors, located in the rear indications of the distance between the rear fascia and the fascia, monitor the area behind the vehicle that is within detected obstacle when backing up.
Page 145: Rear Park Assist Warning Display
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 When the ignition is changed to the RUN/ON position, Rear Park Assist Warning Display The Rear Park Assist Warning Display, located in the the warning display will turn ON all of its LEDs for headliner near the flipper glass, provides both visual and about 1 second.
Page 146: Enable/Disable The Rear Park Assist System
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE When the detected obstacle is about 11.8 inches (30 cm) Enable/Disable the Rear Park Assist System from the rear fascia, the warning display will actuate a The Rear Park Assist System can be enabled and disabled continuous tone for about 10 seconds, and it will turn ON with a switch located in the switch bank of the instru- all 8 LEDs, including both RED LEDs, on the correspond-...
Page 147: Service The Rear Park Assist System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 When the switch is pressed to disable the system, the Service the Rear Park Assist System instrument cluster will display the PARK ASSIST DIS- When the Rear Park Assist System is defective, the ABLED message.
Page 148 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! CAUTION! • • The Rear Park Assist System is only a parking aid Drivers must be careful when backing up even when using the Rear Park Assist System. Always and it is unable to recognize every obstacle, in- check carefully behind your vehicle, look behind cluding small obstacles.
Page 149: Rear Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 NOTE: Clean all four Rear Park Assist Sensors regularly, REAR CAMERA — IF EQUIPPED taking care not to scratch or damage them. The sensors Vehicles with a Navigation radio may be equipped with must not be covered with ice, snow, slush, mud, dirt or a rear view camera (located on the rear liftgate) that debris.
Page 150: Turning The Rear Camera On
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning the Rear Camera On Turning the Rear Camera Off 1. To access the rear camera mode, select “Rear Camera” 1. To turn the rear camera off, select “Rear Camera” at at the Systems Settings screen and press ENTER. Refer to the Systems Settings screen and press ENTER.
Page 151: Overhead Console - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 OVERHEAD CONSOLE — IF EQUIPPED GARAGE DOOR OPENER — IF EQUIPPED The overhead console contains an optional universal The HomeLink Universal Transceiver replaces up to garage door opener (HomeLink ), storage for sunglasses, three remote controls (hand held transmitters) that oper- and optional power sunroof switches.
Page 152 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! A moving garage door can cause injury to people and Vehicle exhaust contains carbon monoxide, a danger- pets in the path of the door. People or pets could be ous gas. Do not run the vehicle’s exhaust while seriously or fatally injured.
Page 153: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
Page 154 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Press and hold the two outer HomeLink buttons, and 2. Position the end of your hand-held transmitter 1-3 release only when the EVIC display shows “CHANNELS inches (3-8 cm) away from the HomeLink buttons. CLEARED”...
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 5. Press and hold the just trained HomeLink button and 6. At the garage door opener receiver (motor-head unit) observe the EVIC display. If the EVIC display shows in the garage, locate the learn or smart button. This “CHANNEL X TRANSMIT”...
Page 156: Canadian Programming/Gate Programming
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To program the remaining two HomeLink but- 3. Continue to press and hold the HomeLink button tons, begin with Programming step two. Do not repeat while you press and release every two seconds ( cycle ) step one.
Page 157: Erasing Homelink Buttons
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 2. The EVIC display will show “CHANNEL X TRANS- Erasing HomeLink Buttons To erase programming from the three buttons (individual MIT” (where X is Channel 1, 2, or 3) for 20 seconds and buttons cannot be erased but can be reprogrammed - then change to “CHANNEL X TRAINING.”...
Page 158: Power Sunroof - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • This device must accept any interference that may be received including interference that may cause undes- ired operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 159: Opening Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Opening Sunroof - Express WARNING! Press the switch rearward and release, and the sunroof • Never leave children in a vehicle, with the keys in will open automatically from any position. The sunroof will open fully, then stop automatically.
Page 160: Pinch Protect Override
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Override Sunshade Operation If a known obstruction (ice, debris, etc.) prevents closing, The sunshade can be opened manually. However, the press the switch forward and hold for two seconds after sunshade will open automatically as the sunroof opens. the reversal occurs.
Page 161: Sunroof Maintenance
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 NOTE: Hold onto shade handle until shade is com- Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean pletely open or closed. the glass panel. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off.
Page 162: Power Outlet
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER OUTLET To the right of the convenience tray (lower center of instrument panel) is an outlet for electrically powered accessories. Pull lightly on the tab of the plastic cover to access the outlet. Rear Power Outlet The power outlets are a direct feed from the battery so they receive power whether the ignition is in the ON or...
Page 163: Cup Holders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 CUP HOLDERS CAUTION! Front Cup Holders Electrical Outlet Use With Engine Off In the center console, there are two cup holders for the • Many accessories that can be plugged in draw front seat passengers. power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 164 164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE cup depression towards the passenger seat, but the top Cup Holders (Third Row Seat) surface will not be flush with the console surface. The third row seat passengers have cup holders on the left and right rear trim panels.
Page 165: Cargo Area Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 CARGO AREA FEATURES Cargo Load Floor The panel in the load floor is reversible for added utility. One side is carpeted and the other side features a plastic lined tray which holds a variety of items. The cargo load floor is held by spring loaded latches.
Page 166: Rear Window Features
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Pull up on loop(s) and twist 90 degrees, so they are 5. Push loop(s) back down, so they are parallel to the top parallel to the slotted hole in tray. of the tray. 3.
Page 167: Rear Window Defroster - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 the rear wiper switch or the ignition switch needs to be turned OFF and ON to restart the rear wiper. Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment on the passenger side and should be checked for fluid level at regular intervals.
Page 168: Roof Luggage Rack - If Equipped
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE install Mopar cross rails built specifically for this roof CAUTION! rack system or a number of after market rails that are tailored to your life-style or activities. To avoid damaging the electrical conductors of the rear window defroster, do not use scrapers, sharp The optional cross rails have five specific locations iden- instruments, or abrasive window cleaners on the...
Page 169 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 NOTE: If the rear cross rail (or any metallic object) is CAUTION! placed over the satellite radio antenna (if equipped), you may experience interruption of satellite radio reception. • To prevent damage to the roof of your vehicle, DO NOT For improved satellite radio reception, place the rear carry any loads on the roof rack without cross rails installed.
Page 170 170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Cargo must be securely tied before driving your vehicle. Improperly secured loads can fly off the vehicle, particularly at high speeds, resulting in personal injury or property damage. Follow the roof rack “Cautions” when carrying cargo on your roof rack.
Page 171: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel And Controls ... . . 174 Radio Broadcast Signals ....197 Instrument Cluster .
Page 172 172 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Operating Instructions - Hands Free Phone — (CD Mode For CD Audio Play) ... 204 If Equipped ......220 Load/Eject Button Operating Instructions - Satellite Radio —...
Page 173 UNDERSTANDING YOUR INSTRUMENT PANEL 173 Electronic Serial Number/Sirius Identification Radio Operation ..... . 231 Number (ESN/SID) ....227 CD Player .
Page 174: Instrument Panel And Controls
174 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND CONTROLS...
Page 175: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 175 INSTRUMENT CLUSTER...
Page 176: Instrument Cluster Description
176 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 3. Turn Signal Indicator Light The arrow will flash with the exterior turn signal 1. Speedometer when the turn signal lever is operated. Indicates vehicle speed. If the vehicle electronics sense that the vehicle has 2.
Page 177 UNDERSTANDING YOUR INSTRUMENT PANEL 177 engine start. If the bulb does not come on when turning during starting, stays on, or turns on while driving, have the key from OFF to ON, have the condition checked the system inspected by an authorized dealer as soon as promptly.
Page 178 178 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Tachometer Do not operate the vehicle until the cause is corrected. The red segments indicate the maximum permissible This light does not show how much oil is in the engine. engine revolutions-per-minute (r.p.m. x 1000) for each The engine oil level must be checked under the hood.
Page 179 UNDERSTANDING YOUR INSTRUMENT PANEL 179 failure. Under-inflation also reduces fuel efficiency and 12. Tire Pressure Monitoring Telltale Light Each tire, including the spare (if provided), tire tread life, and may affect the vehicle’s handling and should be checked monthly when cold and stopping ability.
Page 180 180 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher tempera- CAUTION! ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to The TPMS has been optimized for the original exceed the upper limits of the normal operating range.
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 181 16. Electronic Stability Program (ESP) Warning WARNING! Light/Brake Assist System (BAS) Warning Light The ESP/BAS warning light in the instrument A hot engine cooling system is dangerous. You or cluster comes on when the ignition switch is others could be badly burned by steam or boiling turned to the “ON”...
Page 182 182 UNDERSTANDING YOUR INSTRUMENT PANEL 18. Seat Belt Reminder Light correct mileage that the vehicle has been driven. There- When the ignition switch is first turned ON, this fore, if the odometer reading is changed during repair or light will turn on for 5 to 8 seconds as a bulb check. replacement, be sure to keep a record of the reading During the bulb check, if the driver’s seat belt is before and after the service so that the correct mileage can...
Page 183 UNDERSTANDING YOUR INSTRUMENT PANEL 183 is placed in the P (Park) position. The light should turn 25. Voltage Warning Light off. If the light remains lit with the engine running your This light monitors the electrical system voltage. vehicle will usually be drivable, however, see your dealer The light should turn on momentarily as the for service as soon as possible.
Page 184: Electronic Vehicle Information Center - If Equipped
184 UNDERSTANDING YOUR INSTRUMENT PANEL • TURN SIGNAL ON ELECTRONIC VEHICLE INFORMATION CENTER — IF EQUIPPED • PERFORM SERVICE • KEY NOT PROGRAMMED — DAMAGED KEY • KEY NOT PROGRAMMED — INVALID KEY • KEY NOT PROGRAMMED — EXCEEDED KEY PRO- GRAM LIMIT •...
Page 185 UNDERSTANDING YOUR INSTRUMENT PANEL 185 • LIFTGATE/DOOR OPEN (with graphic) • LIFTGLASS/HOOD OPEN (with graphic) • LIFTGATE/DOORS OPEN (with graphic) • WASHER FLUID LOW (with graphic) • LIFTGLASS OPEN (with graphic) • CHECK GAUGES • HOOD OPEN (with graphic) • AUTO HIGHBEAM ON •...
Page 186 186 UNDERSTANDING YOUR INSTRUMENT PANEL • CHECK GAS CAP • SERVICE TIRE PRESS SYSTEM • ESP OFF • LEFT FRONT LOW PRESSURE (Premium TPM Sys- tem Only) • MEMORY #1 POSITIONS SET • RIGHT FRONT LOW PRESSURE (Premium TPM Sys- •...
Page 187: Customer Programmable Features
UNDERSTANDING YOUR INSTRUMENT PANEL 187 Customer Programmable Features Language? Press the MENU button until one of the display choices When in this display you may select one of three lan- guages for all display nomenclature, including the trip following appears: computer functions.
Page 188 188 UNDERSTANDING YOUR INSTRUMENT PANEL Display U.S. or Metric? Remote Unlock Driver’s Door 1st? Pressing the STEP button when in this display selects US When this feature is selected only the driver’s door will or Metric. The overhead console and instrument panel unlock on the first press of the remote keyless entry unlock displays will be in the selected units.
Page 189 UNDERSTANDING YOUR INSTRUMENT PANEL 189 Sound Horn With Lock? Illuminated Approach? When this feature is selected a short horn sound will When this feature is selected the driver can choose, when occur when the remote keyless entry “Lock” button is entering the vehicle, to have the headlamps come on for 30, pressed.
Page 190 190 UNDERSTANDING YOUR INSTRUMENT PANEL Headlamps On With Wipers? (Available with Auto Service Interval Headlights Only) When this feature is selected a service interval between When this feature is selected and the headlight switch 2,000 (3 200 km) and 6,000 miles (10 000 km) in 500 mile has at least once been moved to the A (Auto) position, the (800 km) increments may be selected.
Page 191: Compass/Temperature/Trip Computer
UNDERSTANDING YOUR INSTRUMENT PANEL 191 Easy Entry/Exit Seat? (Available with Memory Seat Compass/Temperature/Trip Computer Only) This display provides the outside temperature, one of the eight compass headings to indicate the direction the This feature provides automatic driver’s seat positioning vehicle is facing, and vehicle trip information. The com- which will enhance driver mobility out of and into the pass and temperature display is the normal display.
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
Page 193: Trip Computer
UNDERSTANDING YOUR INSTRUMENT PANEL 193 Trip Computer This feature, located in the instrument cluster, displays the following information when the display is in the “Compass/Temperature” mode and the STEP button is pressed: Step Button Press the STEP button to cycle through all of the Compass/Mini-Trip Computer displays.
Page 194 194 UNDERSTANDING YOUR INSTRUMENT PANEL Reset Button Average Fuel Economy Press the RESET button to reset the display you are in. Shows the average fuel economy since the last reset. Press and hold the RESET button (for 2 seconds) to reset When the fuel economy is reset, the display will read all of the displays.
Page 195 UNDERSTANDING YOUR INSTRUMENT PANEL 195 NOTE: Tires heat up during normal driving conditions. Elapsed Time Shows the accumulated ignition ON time since the last Heat will cause the tire pressure to increase from 2 to 6 reset. psi (14 to 41 kPa) during normal driving conditions. Refer to “Tire Inflation Pressures”...
Page 196 196 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. Refer to Variance Map. To Put Into a Calibration Mode Start the engine and leave the transmission in the P (Park) position.
Page 197: Radio General Information
UNDERSTANDING YOUR INSTRUMENT PANEL 197 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the C/T but- ton for approximately 5 seconds. The last variance zone number will be displayed. Press and hold the STEP button for 1 second to select the new variance zone and press the RESET button to resume normal operation.
Page 198: Two Types Of Signals
198 UNDERSTANDING YOUR INSTRUMENT PANEL Two Types of Signals AM Reception There are two basic types of radio signals... AM or AM sound is based on wave amplitude, so AM reception Amplitude Modulation, in which the transmitted sound can be disrupted by such things as lightning, power lines causes the amplitude, or height, of the radio waves to and neon signs.
Page 199: Sales Code Raq - Am/Fm/Cd (6-Disc) Radio With Optional Satellite Radio, Hands Free Phone, And Vehicle Entertainment Systems (Ves) Capabilities
UNDERSTANDING YOUR INSTRUMENT PANEL 199 SALES CODE RAQ – AM/FM/CD (6-DISC) RADIO Operating Instructions - Radio Mode WITH OPTIONAL SATELLITE RADIO, HANDS NOTE: The ignition switch must be in the ON or ACC FREE PHONE, AND VEHICLE ENTERTAINMENT position to operate the radio. SYSTEMS (VES) CAPABILITIES Power Switch/Volume Control (Rotary) NOTE: The radio sales code is located on the lower right...
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button (Radio Mode) will return. Rotating the volume control, turning the Press the mode button repeatedly to select between the radio ON/OFF, or turning OFF the ignition will also CD player, Satellite Radio, or Vehicle Entertainment return the sound from the speakers System (VES) (if equipped).
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 201 Time Button RW/FF (Radio Mode) Press the time button and the time of day will be Pressing the rewind/fast forward button causes the tuner displayed for 5 seconds. to search for the next frequency in the direction of the arrows.
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a third time and TREBLE turning the TUNE rotary knob within 5 seconds will will display. Turn the TUNE control to the right or left to allow the program format type to be selected. Many radio increase or decrease the Treble tones.
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 203 By pressing the SEEK button when the PTY icon is Jazz Jazz displayed, the radio will be tuned to the next frequency News News station with the same selected PTY name. The PTY Nostalgia Nostalgia function only operates when in the FM mode.
Page 204: Operation Instructions - (Cd Mode For Cd Audio Play)
204 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by Operation Instructions - (CD MODE for CD Audio repeating the above procedure with this exception: Press Play) the SET/DIR button twice and SET 2 will show in the NOTE: The ignition switch must be in the ON or ACC display window.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 205 SEEK Button (CD MODE for CD Audio Play) CAUTION! Press the right side of the SEEK button for the next selection on the CD. Press the left side of the button to This CD player will accept 4 3/4 inch (12 cm) discs return to the beginning of the current selection, or return only.
Page 206: Load/Eject Button (Cd Mode For Cd Audio Play)
206 UNDERSTANDING YOUR INSTRUMENT PANEL LOAD/EJECT Button (CD Mode for CD Audio Radio display will show EJECTING DISC when the disc Play) is being ejected and prompt the user to remove the disc. LOAD/ EJECT - Load Press and hold the LOAD/ EJT button for 5 seconds and Press the LOAD/ EJECT button and the push- all CDs will be ejected from the radio.
Page 207 UNDERSTANDING YOUR INSTRUMENT PANEL 207 TIME Button (CD MODE for CD Audio Play) RND/PTY Button (Random Play Button) (CD Press this button to change the display from a large CD MODE for CD Audio Play) playing time display to a small CD playing time display. Press this button while the CD is playing to activate Random Play.
Page 208: Notes On Playing Mp3 Files
208 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of files: 255 Notes On Playing MP3 Files The radio can play MP3 files, however, acceptable MP3 • Maximum number of folders: 100 file recording media and formats are limited. When • Maximum number of characters in file/folder names: writing MP3 files, pay attention to the following restric- tions.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 209 Supported MP3 File Formats MPEG Specifi- Sampling Fre- Bit rate (kbps) The radio will recognize only files with the *.mp3 exten- cation quency (kHz) sion as MP3 files. Non-MP3 files named with the *.mp3 320, 256, 224, extension may cause playback problems.
Page 210: Operation Instructions
210 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files Operation Instructions - (CD Mode for MP3 Audio When a medium containing MP3 data is loaded, the Play) radio checks all files on the medium. If the medium SEEK Button (CD Mode for MP3 Play) contains a lot of folders or files, the radio will take more Pressing the right side of the SEEK button plays the next time to start playing the MP3 files.
Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 211 LOAD / EJECT - Eject MSG or INFO Button (CD Mode for MP3 Play) Press the LOAD/ EJECT button and the push- Press and MSG or INFO button while playing MP3 disc. button with the corresponding number where The radio scrolls through the following TAG information: the CD was loaded and the disc will unload Song Title, Artist, File Name, and Folder Name (if avail-...
Page 212 212 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (CD Mode for MP3 Play) Operating Instructions - Hands Free Phone (If Switches back to Radio mode. Equipped) Refer to Hands Free Phone in Section 3 of the Owner’s RND/ PTY Button (CD Mode for MP3 Play) Manual.
Page 213: Sales Code Ref - Am/Fm/Cd (Single Disc) Radio With Optional Satellite Radio And Hands Free Phone Capability
UNDERSTANDING YOUR INSTRUMENT PANEL 213 SALES CODE REF — AM/FM/CD (SINGLE DISC) Operating Instructions - Radio Mode RADIO WITH OPTIONAL SATELLITE RADIO AND NOTE: The ignition switch must be in the ON or ACC HANDS FREE PHONE CAPABILITY position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of your radio faceplate.
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button (Radio Mode) NOTE: In Hands Free Phone (if equipped) mode, the Press the mode button repeatedly to select between the MUTE button mutes the microphone. CD player and Satellite Radio (if equipped). SCAN Button (Radio Mode) SEEK Button (Radio Mode) Pressing the SCAN button causes the tuner to search for Press and release the SEEK button to search for the next...
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 215 Clock Setting Procedure TUNE Control (Radio Mode) Turn the right side rotary control clockwise to increase or 1. Press and hold the time button until the hours blink. counter-clockwise to decrease the frequency. 2. Adjust the hours by turning the right side Tune/ AM/FM Button (Radio Mode) Audio control.
Page 216 216 UNDERSTANDING YOUR INSTRUMENT PANEL Press the rotary TUNE control a fourth time and BAL will selected within 5 seconds after pressing the SET button, display. Turn the TUNE control to the right or left to the station will continue to play but will not be stored adjust the sound level from the right or left side speakers.
Page 217: Operation Instructions - Cd Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 217 • If you insert a disc with the ignition ON and the radio Operation Instructions - CD Mode OFF, the CD will automatically be pulled into the CD NOTE: The ignition switch must be in the ON or ACC Player.
Page 218 218 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD Mode) RND/SET Button (Random Play Button) (CD Press this button to play the first 10 seconds of each track. Mode) To stop the scan function, press the button a second time. Press this button while the CD is playing to activate Random Play.
Page 219: Operation Instructions - Auxiliary Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Operation Instructions - Auxiliary Mode MUTE Button (Auxiliary Mode) The auxiliary (AUX) jack is an audio input jack, which Press the MUTE button to cancel the sound from the allows the user to plug in a portable device such as an speakers.
Page 220: Operating Instructions - Hands Free Phone
220 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Operating Instructions - Satellite Radio — If Press this button to change the display from elapsed Equipped playing time to time of day. The time of day will display Refer to the “Satellite Radio” section of the Owner’s for 5 seconds.
Page 221: Operating Instructions - Satellite Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 221 Satellite Navigation Radio with CD Player with MP3 REC Setting the Clock Capability (REC) - combines a Global-Positioning GPS Clock System-based navigation system with an integrated color The GPS receiver used in this system is synchronized to screen to provide maps, turn identification, selection the time data being transmitted by the GPS satellites.
Page 222 222 UNDERSTANDING YOUR INSTRUMENT PANEL 1. At the Main Menu screen, highlight “Clock Setup” 2. To show the GPS clock, select “Displayed Clock: GPS and press ENTER OR press and hold for 3 seconds the Clock” and press ENTER. TIME button on the unit’s faceplate. The Clock Setup 3.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 223 1. At the Clock Setup screen highlight “Displayed 3. To decrease the clock by one hour, use the Select Clock: User Defined Clock”. Encoder to highlight the “-” sign. Press ENTER. Press ENTER again to decrease the clock by another hour. 4.
Page 224: Audio Clock Display
224 UNDERSTANDING YOUR INSTRUMENT PANEL Audio Clock Display 3. To switch the clock to the small clock, quickly press TIME again. Select this option to change the size of the clock on the audio screens. 1. When you are at an audio screen, quickly press the TIME button on the navigation faceplate.
Page 225: Video Entertainment System (Sales Code Xrv) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 225 VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (Video Entertainment System) con- sists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two head- sets. The DVD player is mounted in the rear of the center console storage bin, and is concealed by a door that lifts up for access.
Page 226: Satellite Radio - If Equipped
226 UNDERSTANDING YOUR INSTRUMENT PANEL The LCD screen is located on the headliner behind the front seats. Remote Control Location SATELLITE RADIO — IF EQUIPPED Satellite radio uses direct satellite to receiver broadcast- Lowering the Display Screen ing technology to provide clear digital sound, coast to coast.
Page 227: System Activation
UNDERSTANDING YOUR INSTRUMENT PANEL 227 System Activation ESN/SID Access with REC Radios To activate your Sirius Satellite Radio service, call the Refer to the “Navigation User’s Manual” for details on toll-free number 888-539-7474, or visit the Sirius web site satellite radio operation. at www.sirius.com.
Page 228: Selecting Satellite Mode In Ref Radios
228 UNDERSTANDING YOUR INSTRUMENT PANEL • The current program type and channel number will ESN/SID Access with RAQ Radios With the ignition switch in the ACCESSORY position and then be displayed for 5 seconds. the radio OFF, press the CD Eject and TIME buttons •...
Page 229: Storing And Selecting Pre-Set Channels
UNDERSTANDING YOUR INSTRUMENT PANEL 229 NOTE: Channels that may contain objectionable content PTY Button SCAN can be blocked. Contact Sirius Customer Care at 888-539- When the desired program type is obtained, press the 7474 to discuss options for channel blocking or unblock- SCAN button within five seconds.
Page 230: Satellite Antenna
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Placing objects over or too close to the antenna can Satellite Antenna To ensure optimum reception on vehicles available with cause signal blockage. a luggage rack, do not place items on the roof around the REMOTE SOUND SYSTEM CONTROLS —...
Page 231: Radio Operation
UNDERSTANDING YOUR INSTRUMENT PANEL 231 The right hand control is a rocker type switch with a Radio Operation push-button in the center and controls the volume and Pressing the top of the switch will “Seek” up for the next mode of the sound system. Pressing the top of the rocker listenable station and pressing the bottom of the switch switch will increase the volume and pressing the bottom will “Seek”...
Page 232: Cd/Dvd Disc Maintenance
232 UNDERSTANDING YOUR INSTRUMENT PANEL The center button on the left side rocker switch has no 5. Store the disc in its case after playing. function for a single disc CD player. However, when a 6. Do not expose the disc to direct sunlight. multiple disc CD player is equipped on the vehicle, the center button will select the next available CD in the 7.
Page 233: Climate Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 233 The instrument panel features four dual-vane airflow CLIMATE CONTROLS registers. Two registers are located on the outer ends of Manual Air Conditioning and Heating System — If the instrument panel and two are located in the center of Equipped the instrument panel.
Page 234 234 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control Defrost The temperature of air can be selected Air is directed to the windshield through the by rotating the center temperature outlets at the base of the windshield. Air is also control knob. The coldest temperature directed to the front door windows through the side setting is on the extreme left and the window demister grilles.
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 235 Bi-Level Recirculation Air flows both through the outlets located in the The recirculation feature can be selected with instrument panel and those located on the floor. Air the mode control knob. You may choose be- flows through the registers in the back of the center tween Bi-Level Recirculation and Panel Recir- console, and under the front seats to the rear seat...
Page 236: Automatic Temperature Control - If Equipped
236 UNDERSTANDING YOUR INSTRUMENT PANEL Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy. Automatic Temperature Control —...
Page 237 UNDERSTANDING YOUR INSTRUMENT PANEL 237 LO AUTO position should be used for front seat occu- temperature out of the ducts will be full hot or full cold pants only. The HI AUTO position should be used when respectively. With the temperature setting in these posi- more air flow is desired, or when rear seat occupants are tions, the system does not attempt automatic comfort present.
Page 238 238 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: certain conditions in automatic the system is blowing • The surface of the climate control panel, and the top air out of the defrost vents. When these conditions are center of the instrument panel should be kept free of present and the Recirc button is pressed the indicator debris due to the climate control sensor’s location.
Page 239 UNDERSTANDING YOUR INSTRUMENT PANEL 239...
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Regardless of the type of operation, when a NOTE: The defrost mode is not automatically selected. temperature knob is set to the full clockwise or full It must be manually selected, when desired. counterclockwise position, the system will deliver full •...
Page 241 UNDERSTANDING YOUR INSTRUMENT PANEL 241 Air flows through the registers in the back of the This button can be used to block out smoke, center console, and under the front seats to the rear odors, dust, high humidity, or if rapid cooling seat passengers.
Page 242: Rear Climate Control - If Equipped
242 UNDERSTANDING YOUR INSTRUMENT PANEL Rear Climate Control — If Equipped The Manual Rear Climate Control system has one floor air outlet (passenger side), and two panel outlets in the rear quarter trim (on each side). The unit provides warm or cool air through the floor and upper outlets.
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 243 The rear temperature, blower speed, and mode control can Rear Blower Control be adjusted as desired by the third row seat occupants. The left knob on the Rear Control Panel has four posi- tions, “Off”, and a range of three blower speeds. This allows the third row seat occupants to control the volume of air circulated in the rear of the vehicle.
Page 244: Operating Tips
244 UNDERSTANDING YOUR INSTRUMENT PANEL • Panel Rear Temperature Control The center knob on the Rear Control Panel allows the Air flows through the outlets located in the rear third row seat occupants to have control of the rear quarter trim panels. These registers can be closed temperature as follows: to block airflow.
Page 245 UNDERSTANDING YOUR INSTRUMENT PANEL 245 Regular cleaning of the inside of the windows with a N (Neutral) and depress the accelerator slightly for fast non-filming cleaning solution (vinegar and water works idle operation to increase coolant flow and fan speed. very well) will help prevent contaminates (cigarette Your air conditioning system is also equipped with an smoke, perfumes, etc.) from sticking to the windows.
Page 246: Operating Tips Chart
246 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart...
Page 247: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 251 Gear Ranges ......257 Normal Starting .
Page 248 248 STARTING AND OPERATING On-Road Driving Tips ....269 Tire Safety Information ....280 Off-Road Driving Tips .
Page 249 STARTING AND OPERATING 249 Alignment And Balance ....294 Materials Added To Fuel ....309 Tire Chains .
Page 250 250 STARTING AND OPERATING Adding Fuel ......314 Towing Requirements ....327 Fuel Filler Cap (Gas Cap) .
Page 251: Starting Procedures
STARTING AND OPERATING 251 Start the engine with the gear selector in the N (Neutral) STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust both or P (Park) position. Apply the brakes before shifting to inside and outside mirrors, and fasten your seat belts. any driving gear.
Page 252: Extreme Cold Weather (Below -20°F (-29°C)
252 STARTING AND OPERATING NOTE: The starter motor may run up to 30 seconds in Extreme Cold Weather (below –20°F (–29°C) very cold conditions until the engine is started. The To insure reliable starting at these temperatures, use of an starter can be disengaged by turning the ignition key to externally powered electric engine block heater (available the OFF position, if required.
Page 253 STARTING AND OPERATING 253 WARNING! WARNING! Never pour fuel or other flammable liquids into the Do not attempt to push or tow your vehicle to get it throttle body air inlet opening in an attempt to start started. Vehicles equipped with an automatic trans- the vehicle.
Page 254: After Starting
254 STARTING AND OPERATING If the engine has been flooded, it may start to run, but not CAUTION! have enough power to continue running when the key is released. If this occurs, continue cranking with the accel- Long periods of engine idling, especially at high erator pedal pushed all the way to the floor.
Page 255: Engine Block Heater - If Equipped
STARTING AND OPERATING 255 ENGINE BLOCK HEATER — IF EQUIPPED AUTOMATIC TRANSMISSION The engine block heater warms engine coolant and permits quicker starts in cold weather. Connect the cord CAUTION! to a standard 110-115 volt AC electrical outlet with grounded, three wire extension cord. Damage to the transmission may occur if the follow- Use the heater when temperatures below 0°F (-18°C) are ing precautions are not observed:...
Page 256: Brake/Transmission Interlock System
256 STARTING AND OPERATING 5–Speed Automatic Transmission WARNING! The electronically controlled transmission provides a precise shift schedule. The transmission electronics are It is dangerous to shift the selector lever out of P self-calibrating; therefore, the first few shifts on a new (Park) or N (Neutral) if the engine speed is higher vehicle, may be somewhat abrupt.
Page 257: Gear Ranges
STARTING AND OPERATING 257 Gear Ranges WARNING! NOTE: After selecting any gear range, wait a moment to Never use P (Park) position as a substitute for the allow the selected gear to engage before accelerating. parking brake. Always apply parking brake fully This is especially important when the engine is cold.
Page 258 258 STARTING AND OPERATING R (Reverse) Electronic Range Select (ERS)Operation Use this range only after the vehicle has come to a The Electronic Range Select (ERS) shift control allows complete stop. you to move the shifter left (-) or right (+) when the shifter is in the D (Drive) position, allowing the selection N (Neutral) of the desired top gear.
Page 259 STARTING AND OPERATING 259 Overdrive Operation WARNING! The automatic transmission includes an electronically controlled Overdrive (5th gear for 3.7L engine, 4th and Do not downshift for additional engine braking on a 5th gears for 4.7L and 5.7L engines). The transmission slippery surface.
Page 260 260 STARTING AND OPERATING NOTE: If the vehicle is started in extremely cold tem- In high ambient temperatures with sustained high engine peratures, the transmission may not shift into Overdrive speed and load, an upshift followed shortly thereafter by and will automatically select the most desirable gear for a downshift may occur.
Page 261 STARTING AND OPERATING 261 Transmission Limp Home Mode Transmission function is monitored for abnormal condi- tions. If a condition is detected that could result in transmission damage, the transmission limp home mode will be engaged. In this mode, the transmission will remain in the current gear (3.7L engine) or in direct gear (4.7L and 5.7L engines) until the vehicle is brought to a stop.
Page 262 262 STARTING AND OPERATING If the problem is no longer detected, the transmission will NOTE: The torque converter clutch will not engage return to normal operation. If the problem persists, P until the transmission fluid and engine coolant are warm (Park), R (Reverse), and N (Neutral) will continue to [usually after 1-3 miles (1.6 - 4.8 km) of driving].
Page 263: Rocking The Vehicle
STARTING AND OPERATING 263 five rocking-motion cycles. This will minimize overheat- Rocking the Vehicle If the vehicle becomes stuck in snow, sand, or mud, it can ing and reduce the risk of transmission failure during often be moved by a rocking motion. Move the gear prolonged efforts to free a stuck vehicle.
Page 264: Four-Wheel Drive Operation
264 STARTING AND OPERATING FOUR-WHEEL DRIVE OPERATION Quadra-Trac II Operating Instructions/Precautions — If Equipped Quadra-Trac I Operating The Quadra-Trac II transfer case is fully automatic in the Instructions/Precautions — If Equipped normal driving 4 HI mode. The Quadra-Trac II transfer The Quadra-Trac I is a single speed (HI range only) case provides three mode positions —...
Page 265: Shift Positions
STARTING AND OPERATING 265 road surfaces only. Driving in the 4 LOW position on dry WARNING! hard surfaced roads may cause increased tire wear and damage to driveline components. You or others could be injured if you leave the vehicle unattended with the transfer case in the N When operating your vehicle in 4 LOW, the engine speed (Neutral) position without first fully engaging the is approximately three times that of the 4 HI position at a...
Page 266: Shifting Procedures
266 STARTING AND OPERATING N (Neutral) Shifting Procedures Neutral — Disengages both the front and rear driveshafts 4 HI to 4 LOW from the powertrain. To be used for flat towing behind With the vehicle at speeds of 0 to 3 mph (0 to 5 km/h), another vehicle.
Page 267 STARTING AND OPERATING 267 LOW Indicator Lamp” in the instrument cluster will flash and go out when the shift is complete. Release the T-handle. NOTE: If shift conditions/interlocks are not met, or a transfer case motor temperature protection condition exists, a “CHECK SHIFT PROCEDURES” message will flash from the EVIC (Electronic Vehicle Information Cen- ter).
Page 268 268 STARTING AND OPERATING Neutral (N) Shift Procedure 1. Key ON, engine off. 2. Vehicle stopped, with foot on brake. 3. Place transmission in N (Neutral). 4. Hold down N (Neutral) “pin” switch (with a pen, etc.) for 4 seconds until the LED lamp by the switch starts to blink indicating shift in progress.
Page 269: Quadra-Drive Ii System - If Equipped
STARTING AND OPERATING 269 Quadra-Drive II System — If Equipped ON-ROAD DRIVING TIPS The optional Quadra-Drive II System features three Utility vehicles have higher ground clearance and a torque transfer couplings. The couplings include ELSD narrower track to make them capable of performing in a (Electronic Limited Slip Differential) front and rear axles wide variety of off-road applications.
Page 270: Off-Road Driving Tips
270 STARTING AND OPERATING OFF-ROAD DRIVING TIPS CAUTION! NOTE: Prior to off-road driving, remove the front air When driving through water, do not exceed 5 mph (8 dam to prevent damage. The front air dam is attached to km/h). Always check water depth before entering as the lower front fascia with quarter turn fasteners, and can a precaution, and check all fluids afterward.
Page 271: Driving In Snow, Mud And Sand
STARTING AND OPERATING 271 and/or the flow rate is reduced. If you must cross Driving In Snow, Mud and Sand flowing water avoid depths in excess of 9 inches. The In heavy snow, when pulling a load, or for additional flowing water can erode the streambed causing your control at slower speeds, shift the transmission to a low vehicle to sink into deeper water.
Page 272: Traction Downhill
272 STARTING AND OPERATING If you stall or begin to lose headway while climbing a Remember, never drive diagonally across a hill-always steep hill, allow your vehicle to come to a stop and drive straight up or down. immediately apply the brakes. Restart the engine and If the wheels start to slip as you approach the crest of a shift to R (Reverse).
Page 273: After Driving Off-Road
STARTING AND OPERATING 273 • After extended operation in mud, sand, water, or After Driving Off-Road Off-road operation puts more stress on your vehicle than similar dirty conditions, have brake rotors, wheels, does most on-road driving. After going off-road it is brake linings, and axle yokes inspected and cleaned as always a good idea to check for damage.
Page 274: Parking Brake
274 STARTING AND OPERATING PARKING BRAKE To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the “Brake Warning Light” in the instru- ment cluster will light. To release the parking brake, pull up slightly, press the center button, then lower the lever completely.
Page 275: Anti-Lock Brake System
STARTING AND OPERATING 275 When parking on a hill, turn the front wheels toward the WARNING! curb on a downhill grade and away from the curb on an • Always fully apply the parking brake when leav- uphill grade. ing your vehicle, or it may roll and cause damage The parking brake should always be applied whenever or injury.
Page 276 276 STARTING AND OPERATING WARNING! WARNING! Significant over or under inflation of tires, or mixing Pumping of the Anti-Lock Brakes will diminish sizes of tires or wheels on the vehicle can lead to loss their effectiveness and may lead to an accident. of braking effectiveness.
Page 277 STARTING AND OPERATING 277 WARNING! CAUTION! • The Anti-Lock Brake System (ABS) cannot pre- The Anti-Lock Brake System is subject to possible vent the natural laws of physics from acting on the detrimental effects of electronic interference caused vehicle, nor can it increase braking or steering by improperly installed after-market radios or tele- efficiency beyond that afforded by the condition phones.
Page 278: Power Steering
278 STARTING AND OPERATING • Do not “ride” the brakes by resting your foot on the build up between the tire tread and the road. This pedal. This could overheat the brakes and result in hydroplaning action can cause loss of traction, braking unpredictable braking action, longer stopping dis- ability, and control.
Page 279: Multi Displacement System (Mds) - 5.7L Engine
STARTING AND OPERATING 279 NOTE: Increased noise levels at the end of the steering CAUTION! wheel travel are considered normal and do not indicate that there is a problem with the power steering system. Prolonged operation of the steering system at the end of the steering wheel travel will increase the Upon initial start-up in cold weather, the power steering steering fluid temperature and it should be avoided...
Page 280: Tire Safety Information
280 STARTING AND OPERATING • European Metric tire sizing is based on European TIRE SAFETY INFORMATION design standards. Tires designed to this standard have Tire Markings the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 281 STARTING AND OPERATING 281 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 282 282 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 283: Tire Identification Number (Tin)
STARTING AND OPERATING 283 Look for the TIN on the outboard side of black sidewall Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire; tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 284: Tire Loading And Tire Pressure
284 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 285 STARTING AND OPERATING 285 To determine the maximum loading conditions of your Loading The vehicle maximum load on the tire must not exceed vehicle, locate the statement “The combined weight of the load carrying capacity of the tire on your vehicle. You occupants and cargo should never exceed XXX kg or XXX will not exceed the tire’s load carrying capacity if you lbs.”...
Page 286 286 STARTING AND OPERATING 4. The resulting figure equals the available amount of manual to determine how this reduces the available cargo and luggage load capacity. For example, if “XXX” cargo and luggage load capacity of your vehicle. amount equals 1400 lbs. and there will be five 150 lb. NOTE: The following table shows examples on how to passengers in your vehicle, the amount of available cargo calculate total load, cargo/luggage, and towing capaci-...
Page 287 STARTING AND OPERATING 287...
Page 288: Tires - General Information
288 STARTING AND OPERATING 1. Safety— WARNING! Overloading of your tires is dangerous. Overloading WARNING! can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the Improperly inflated tires are dangerous and can cause accidents. recommended load capacity for your vehicle.
Page 289: Tire Inflation Pressures
STARTING AND OPERATING 289 2. Economy— Tire Inflation Pressures Improper inflation pressures can cause uneven wear The proper cold tire inflation pressure is listed on either patterns to develop across the tire tread. These abnormal the face of the driver’s door, or the driver’s side “B” pillar. wear patterns will reduce tread life resulting in a need for earlier tire replacement.
Page 290 290 STARTING AND OPERATING The pressure should be checked and adjusted as well as Check tire pressures more often if subject to a wide range inspecting for signs of tire wear or visible damage at least of outdoor temperatures, as tire pressures vary with once a month.
Page 291: Tire Pressures For High Speed Operation
STARTING AND OPERATING 291 Tire Pressures for High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- WARNING! tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very Combining radial ply tires with other types of tires important.
Page 292: Tread Wear Indicators
292 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck, and do not let anyone near a spinning wheel no matter what the speed.
Page 293: Life Of Tire
STARTING AND OPERATING 293 Keep unmounted tires in a cool, dry place with as little Life of Tire The service life of a tire is dependent upon varying exposure to light as possible. Protect tires from contact factors including but not limited to: with oil, grease and gasoline.
Page 294: Alignment And Balance
294 STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than Replacing original tires with tires of a different size that specified for your vehicle. Some combina- may result in false speedometer and odometer read- tions of unapproved tires and wheels may change ings.
Page 295: Tire Chains
STARTING AND OPERATING 295 • Use SAE class “S” tire chains or traction devices only. Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- • Follow tire chain manufacturer’s instructions for balance. Proper balancing will reduce vibration and mounting chains.
Page 296: Tire Rotation Recommendations
296 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS NOTE: The Premium Tire Pressure Monitor System will Tires on the front and rear axles of vehicles operate at automatically locate the pressure values displayed in the different loads and perform different steering, handling, correct vehicle position following a tire rotation.
Page 297: Tire Pressure Monitor System (Tpms)
STARTING AND OPERATING 297 The TPM System will warn the driver of a low tire TIRE PRESSURE MONITOR SYSTEM (TPMS) The Tire Pressure Monitoring System (TPMS) will warn pressure if the tire pressure falls below the low pressure the driver of a low tire pressure based on the vehicle warning threshold for any reason, including low tem- recommended cold tire pressure.
Page 298: Base System - If Equipped
298 STARTING AND OPERATING For example, your vehicle has a recommended cold Base System — If Equipped (parked for more than 3 hours) tire pressure of 35 psi (241 The Tire Pressure Monitor System (TPMS) uses wireless kPa). If the ambient temperature is 68°F (20°C) and the technology with wheel rim mounted electronic sensors to measured tire pressure is 30 psi (207 kPa), a temperature monitor tire pressure levels.
Page 299 STARTING AND OPERATING 299 A tire pressure monitoring sensor is located in the spare The “Tire Pressure Monitoring Telltale Light” will flash wheel if the vehicle is equipped with a matching full size on and off for 60 seconds, and an audible chime will spare wheel and tire assembly.
Page 300 300 STARTING AND OPERATING NOTE: If your vehicle is equipped with a non-matching CAUTION! full size spare tire, it does not have a tire pressure monitoring sensor. Therefore, it will not be monitored by The TPMS has been optimized for the original the Tire Pressure Monitor System (TPMS).
Page 301: Premium System - If Equipped
STARTING AND OPERATING 301 Under-inflation also reduces fuel efficiency and tire CAUTION! tread life, and may affect the vehicle’s handling and stopping ability. After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent •...
Page 302 302 STARTING AND OPERATING The Tire Pressure Monitor System (TPMS) consists of the Tire Pressure Monitoring Low Pressure Warnings following components: The “Tire Pressure Monitoring Telltale Light” will illuminate in the instrument cluster, and an au- • Receiver Module dible chime will be activated when one or more of •...
Page 303 STARTING AND OPERATING 303 NOTE: If your vehicle is equipped with a non-matching Should a low tire condition occur on any of the four full size spare tire, a low non-matching full size spare tire active road tire(s), you should stop as soon as possible, will not display any text messages, or cause the “Tire and inflate the low tire(s) that is flashing on the graphic Pressure Monitoring Telltale Light”...
Page 304 304 STARTING AND OPERATING The EVIC will display the “SERVICE TIRE PRESS. SYS- If the ignition key is cycled, this sequence will repeat, TEM” message for 3 seconds. This text message is then providing the system fault still exists. If the system fault followed by a graphic, with “- -“...
Page 305 STARTING AND OPERATING 305 low pressure warning threshold. The EVIC will display a Telltale Light” will be OFF as long as none of the road “Spare Low Pressure” text message, and the graphic tire(s) are below the low pressure warning threshold. The display will show a new tire pressure value in place of vehicle may need to be driven for up to 10 minutes above the flashing low tire pressure value.
Page 306: General Information
306 STARTING AND OPERATING Under-inflation also reduces fuel efficiency and tire CAUTION! tread life, and may affect the vehicle’s handling and stopping ability. After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap. This will prevent •...
Page 307: Fuel Requirements
STARTING AND OPERATING 307 The tire pressure sensors are covered under one of the 5.7L Engines (If Equipped) following licenses: The 5.7L engine is designed to meet all emissions regulations and provide satisfac- tory fuel economy and performance when United States ..... KR5S120123 using high quality unleaded gasoline hav- Canada .
Page 308: Reformulated Gasoline
308 STARTING AND OPERATING Poor quality gasoline can cause problems such as hard The manufacturer supports the use of reformulated gaso- starting, stalling and hesitations. If you experience these lines. Properly blended reformulated gasolines will pro- symptoms, try another brand of gasoline before consid- vide excellent performance and durability of engine and ering service for the vehicle.
Page 309: Mmt In Gasoline
STARTING AND OPERATING 309 Problems that result from using methanol/gasoline or It is even more important to look for gasolines without E85 Ethanol blends are not the responsibility of the MMT in Canada, because MMT can be used at levels manufacturer.
Page 310: Fuel System Cautions
310 STARTING AND OPERATING • The use of fuel additives which are now being sold as Fuel System Cautions octane enhancers is not recommended. Most of these products contain high concentrations of methanol. CAUTION! Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives is not Follow these guidelines to maintain your vehicle’s the responsibility of the manufacturer.
Page 311: Flexible Fuel (4.7L Only) - If Equipped
STARTING AND OPERATING 311 • Do not inhale exhaust gases. They contain carbon FLEXIBLE FUEL (4.7L ONLY) — IF EQUIPPED monoxide, a colorless and odorless gas which can kill. E-85 General Information Never run the engine in a closed area, such as a The information in this section is for Flexible Fuel garage, and never sit in a parked vehicle with the vehicles only.
Page 312: Ethanol Fuel (E-85)
312 STARTING AND OPERATING ETHANOL FUEL (E-85) For best results, a refueling pattern that alternates be- E-85 is a mixture of approximately 85% fuel ethanol and tween E-85 and unleaded gasoline should be avoided. 15% unleaded gasoline. When you do switch fuels, it is recommended that •...
Page 313: Selection Of Engine Oil For Flexible Fuel
STARTING AND OPERATING 313 Selection Of Engine Oil For Flexible Fuel Vehicles Cruising Range (E-85) and Gasoline Vehicles Because E-85 fuel contains less energy per gallon than Whether operating the vehicle on an E-85 ethanol fuel or gasoline, you will experience an increase in fuel con- unleaded gasoline the engine oil requirements are the sumption.
Page 314: Maintenance
314 STARTING AND OPERATING Maintenance If you operate the vehicle using E-85 fuel, follow “Main- tenance Schedule B.” Refer to Section 8 of this manual. CAUTION! Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability.
Page 315 STARTING AND OPERATING 315 CAUTION! CAUTION! Damage to the fuel system or emission control To avoid fuel spillage and overfilling, do not “top system could result from using an improper fuel cap off” the fuel tank after filling. (gas cap). A poorly fitting cap could let impurities into the fuel system.
Page 316 316 STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you WARNING! hear one click. This is an indication that cap is properly tightened. A fire may result if gasoline is pumped into a portable container that is inside of a vehicle. You If the gas cap is not tighten properly, the Malfunction could be burned.
Page 317: Vehicle Loading
STARTING AND OPERATING 317 Hour of manufacture. The bar code that appears on the WARNING! bottom of the label is your Vehicle Identification Number • Never add fuel when the engine is running. (VIN). • Never have any smoking materials lit in or near Gross Vehicle Weight Rating (GVWR) the vehicle when the fuel cap is removed or the The GVWR is the total permissible weight of your vehicle...
Page 318 318 STARTING AND OPERATING Each axle GAWR is determined by the components in the Curb Weight system with the lowest load carrying capacity (axle, The curb weight of a vehicle is defined as the total weight springs, tires or wheels). Heavier axles or suspension of the vehicle with all fluids, including vehicle fuel, at full components sometimes specified by purchasers for in- capacity conditions, and with no occupants or cargo...
Page 319: Trailer Towing
STARTING AND OPERATING 319 or rear axles has been exceeded but the total load is TRAILER TOWING within the specified GVWR. If so, weight must be shifted In this section you will find safety tips and information from front to rear or rear to front as appropriate until the on limits to the type of towing you can reasonably do specified weight limitations are met.
Page 320 320 STARTING AND OPERATING Gross Trailer Weight (GTW) Gross Axle Weight Rating (GAWR) The gross trailer weight (GTW) is the weight of the trailer The GAWR is the maximum capacity of the front and rear plus the weight of all cargo, consumables and equipment axles.
Page 321 STARTING AND OPERATING 321 Frontal Area Weight-Distributing Hitch The maximum height and maximum width of the front of A weight-distributing system works by applying lever- a trailer. age through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to Trailer Sway Control the tow vehicle’s front axle and the trailer axle(s).
Page 322 322 STARTING AND OPERATING WARNING! An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking per- formance, and could result in an accident. Weight Distributing Systems may not be compatible with Surge Brake Couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
Page 323: Trailer Hitch Classification
STARTING AND OPERATING 323 Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of trailers weighing over 3,500 lbs (1 587 kg) with the optional Trailer Tow Prep Package. See your dealer for package content. The following chart provides the industry standard for the maximum trailer weight a given trailer hitch class can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
Page 324: Trailer Towing Weights (Maximum Trailer Weight Ratings)
324 STARTING AND OPERATING All trailer hitches should be professionally installed on Trailer Hitch Classification your vehicle. Class Max. GTW (Gross Trailer Wt.) Trailer Towing Weights (Maximum Trailer Weight Class I - Light Duty 2,000 lbs (907 kg) Ratings) The following chart provides the maximum trailer Class II - Medium 3,500 lbs (1 587 kg) Duty...
Page 325 STARTING AND OPERATING 325 Engine/ Model GCWR (Gross Com- Frontal Area Max. GTW (Gross Max. Tongue Wt. Transmission bined Wt. Rating) Trailer Wt.) (See Note 1) 3.7L/ 8,670 lbs (3 933 kg) 40 Sq. Ft (3.72 3,500 lbs (1 587 kg) 350 lbs (159 kg) Automatic square meters)
Page 326: Trailer And Tongue Weight
326 STARTING AND OPERATING Trailer and Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
Page 327: Towing Requirements
STARTING AND OPERATING 327 NOTE: Remember that everything put into or on the CAUTION! trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, • Avoid towing a trailer for the first 500 miles (805 must be considered as part of the total load on your km) of vehicle operation.
Page 328 328 STARTING AND OPERATING • Safety chains must always be used between your WARNING! vehicle and trailer. Always connect the chains to the hook retainers of the vehicle hitch. Cross the chains Improper towing can lead to an injury accident. under the trailer tongue and allow enough slack for Follow these guidelines to make your trailer towing turning corners.
Page 329 STARTING AND OPERATING 329 3. GAWR Information section of this manual on Tread Wear Indicators for the proper inspection procedure. 4. Tongue weight rating for the trailer hitch utilized (This requirement may limit the ability to always − When replacing tires, refer to the Tires–General Infor- achieve the 10% to 15% range of tongue weight as a mation section of this manual on Replacement Tires for percentage of total trailer weight).
Page 330 330 STARTING AND OPERATING − Trailer brakes are recommended for trailers over 1,000 WARNING! lbs (454 kg) and required for trailers in excess of 2,000 lbs (907 kg). Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail.
Page 331: Towing Tips
STARTING AND OPERATING 331 The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. 7- Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer in an area away from heavy 4 - Pin Connector traffic.
Page 332 332 STARTING AND OPERATING Towing Tips — Automatic Transmission Towing Tips — Electronic Speed Control (If The “D” range can be selected when towing. However, if Equipped) frequent shifting occurs while in this range, the ”Tow/ − Don’t use in hilly terrain or with heavy loads. Haul”...
Page 333: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 333 − Air Conditioning Towing — Quadra-Trac I (Single-Speed Transfer Turn off temporarily. Case) 4WD Models − refer to Cooling System Operating information in the Recreational towing is not allowed. This model does not Maintenance section of this manual for more informa- have a N (Neutral) position in the transfer case.
Page 334 334 STARTING AND OPERATING Shifting Into Neutral (N) 1. Depress brake pedal. Use the following procedure to prepare your vehicle for 2. Turn the ignition key ON, engine off. recreational towing. 3. Shift transmission into N (Neutral). 4. Shift transfer case into N (Neutral). CAUTION! Hold down N (Neutral) “pin”...
Page 335 STARTING AND OPERATING 335 9. Shift transmission into P (Park). 10. Place the ignition key in the OFF position, and remove key. 11. Apply parking brake. 12. Attach vehicle to the tow vehicle with tow bar. 13. Release parking brake. CAUTION! Transmission damage may occur if the transmission Neutral Switch...
Page 336 336 STARTING AND OPERATING Shifting Out Of Neutral (N) Use the following procedure to prepare your vehicle for normal usage. 1. Depress brake pedal. 2. Turn the ignition key ON, engine off. 3. Shift transmission into N (Neutral). 4. Shift transfer case out of N (Neutral). Hold down N (Neutral) “pin”...
Page 337: Snow Plow
STARTING AND OPERATING 337 NOTE: When shifting out of transfer case N (Neutral), CAUTION! turning the engine OFF may be required to avoid gear clash. Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. WARNING! SNOW PLOW You or others could be injured if you leave the...
Page 338 338 STARTING AND OPERATING WARNING! Do not add a snow plow, winches, or any other aftermarket equipment to the front of your vehicle. This could adversely affect the functioning of the airbag system and you could be injured.
Page 339: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flashers ....340 Jacking Instructions ....345 If Your Engine Overheats .
Page 340: Hazard Warning Flashers
340 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle.
Page 341: If Your Engine Overheats
WHAT TO DO IN EMERGENCIES 341 IF YOUR ENGINE OVERHEATS CAUTION! In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- Driving with a hot cooling system could damage tion. your vehicle. If the temperature gauge reads “H”, pull over and stop the vehicle.
Page 342: Jacking And Tire Changing
342 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location The scissor-type jack and tire changing tools are located in a compartment behind the third row seat. Refer to WARNING! “Cargo Area Features” in Section 3 of this manual. •...
Page 343: Spare Tire Stowage
WHAT TO DO IN EMERGENCIES 343 Spare Tire Stowage The spare tire is stowed under the rear of the vehicle by means of a cable winch mechanism. To remove or stow the spare, use the jack handle to rotate the “spare tire drive”...
Page 344: Spare Tire Removal
344 WHAT TO DO IN EMERGENCIES Spare Tire Removal Preparations For Jacking Fit the jack handle extension over the drive nut. Use the Park the vehicle on a firm level surface, avoid ice or Lug Wrench to rotate the nut counter clockwise until the slippery areas, set the parking brake and place the gear spare is on the ground with enough slack in the cable to selector in P (Park).
Page 345: Jacking Instructions
WHAT TO DO IN EMERGENCIES 345 For example, if changing the right front tire, block the 3. Assemble the jack and jacking tools as shown. Connect left rear wheel. jack handle driver (A) to two extensions (B), then to the lug wrench (C).
Page 346 346 WHAT TO DO IN EMERGENCIES 4. Locate the jack as shown. For the front axle, place it under the front lower control arm as shown. For the rear axle, place it under the axle near the wheel to be changed. Ensure the jack is closest to the inside of the wheel when jacking on the rear axle.
Page 347 WHAT TO DO IN EMERGENCIES 347 9. Finish tightening the lug nuts. Push down on the WARNING! wrench while tightening for increased leverage. Alternate nuts until each nut has been tightened twice. Correct Raising the vehicle higher than necessary can make wheel nut tightness is 130 N·m (95 ft.
Page 348: Jump Starting
348 WHAT TO DO IN EMERGENCIES NOTE: Tire should be stowed with the “beauty” side JUMP STARTING up. Storing the tire upside down may result in scratching If the vehicle has a discharged battery, booster cables may be or damage to the wheel face. Continue winching up the used to obtain a start from a booster battery or the battery in tire until you hear the winch “ratchet”...
Page 349 WHAT TO DO IN EMERGENCIES 349 1. Remove all metal jewelry such as watch bands or WARNING! bracelets which might make an unintended electrical contact. Do not permit vehicles to touch each other as this could establish a ground connection and personal 2.
Page 350 350 WHAT TO DO IN EMERGENCIES 4. Connect one end of a jumper cable to the positive 7. When removing the jumper cables, reverse the above terminal of the booster battery. Connect the other end of sequence exactly. Be careful of the moving belts and fan. the same cable to the positive terminal of the discharged battery.
Page 351: Emergency Tow Hooks - If Equipped
WHAT TO DO IN EMERGENCIES 351 EMERGENCY TOW HOOKS — IF EQUIPPED WARNING! If your vehicle is equipped with tow hooks, there will be • You should not try to start your vehicle by push- one in the rear and two mounted on the front of the vehicle.
Page 352: Towing A Disabled Vehicle
352 WHAT TO DO IN EMERGENCIES (24 km) can cause severe transmission damage. If the WARNING! transmission is not operable, or the vehicle must be towed faster than 30 mph (48 km/h) or farther than 15 Stand clear of vehicles when pulling with tow miles (24 km), remove the driveshaft or tow with all four hooks.
Page 353: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment – 3.7L ....355 Maintenance Procedures ....362 Engine Compartment –...
Page 354 354 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance ... . . 371 Appearance Care And Protection From Corrosion ......388 Power Steering Fluid Check .
Page 355: Engine Compartment - 3.7L
MAINTAINING YOUR VEHICLE 355 ENGINE COMPARTMENT – 3.7L...
Page 356: Engine Compartment - 4.7L
356 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 4.7L...
Page 357: Engine Compartment - 5.7L
MAINTAINING YOUR VEHICLE 357 ENGINE COMPARTMENT – 5.7L...
Page 358: Onboard Diagnostic System - Obd Ii
358 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 359: Loose Fuel Filler Cap Message
MAINTAINING YOUR VEHICLE 359 If the problem persists, the message will appear the next Loose Fuel Filler Cap Message After fuel is added, the vehicle diagnostic system can time the vehicle is started. This might indicate a damaged determine if the fuel filler cap is loose, improperly installed, cap.
Page 360 360 MAINTAINING YOUR VEHICLE Normally, the OBD system will be ready. The OBD 5. Approximately 15 seconds later, one of two things will system may not be ready if your vehicle was recently happen: serviced, if you recently had a dead battery, or a battery a.
Page 361: Replacement Parts
MAINTAINING YOUR VEHICLE 361 Regardless of whether your vehicle’s OBD system is DEALER SERVICE ready or not ready, if the MIL symbol is illuminated Your dealer has the qualified service personnel, special during normal vehicle operation, you should have your tools and equipment to perform all service operations in vehicle serviced before going to the I/M station.
Page 362: Maintenance Procedures
362 MAINTAINING YOUR VEHICLE MAINTENANCE PROCEDURES check the engine oil level is about 5 minutes after a fully The pages that follow contain the required maintenance warmed engine is shut off or before starting the engine services determined by the engineers who designed your after it has sat overnight.
Page 363 MAINTAINING YOUR VEHICLE 363 • If equipped for and operating with E-85 (ethanol) Change Engine Oil Road conditions as well as your kind of driving affect the fuel. interval at which your oil should be changed. Check the If ANY of these apply to you, then change your engine oil following to determine if any apply to you: every 3,000 miles (5 000 km) or 3 months, whichever •...
Page 364 364 MAINTAINING YOUR VEHICLE Material Standard MS-6395. Use Mopar or an equiva- Engine Oil Viscosity (3.7L/4.7L/5.7L Engines) lent oil meeting the specification MS-6395. SAE 5W-20 engine oil is recommended for all operating temperatures. This engine oil improves low tempera- American Petroleum Institute (API) Engine Oil ture starting and vehicle fuel economy.
Page 365: Drive Belts - Check Condition And Tension
MAINTAINING YOUR VEHICLE 365 Materials Added to Engine Oils Engine Oil Filter Selection The manufacturer strongly recommends against the ad- All of the manufacturer’s engines have a full-flow type dition of any additives (other than leak detection dyes) to disposable oil filter. Use a filter of this type for replace- engine oil.
Page 366: Spark Plugs
366 MAINTAINING YOUR VEHICLE Belts should be inspected for evidence of cuts, cracks, Spark Plug Wires glazing, or frayed cords and replaced if there is indication The spark plug wires should be kept clean and properly of damage which could result in belt failure. Low gen- connected.
Page 367: Catalytic Converter
MAINTAINING YOUR VEHICLE 367 Under normal operating conditions, the catalytic con- WARNING! verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure The air induction system (air cleaner, hoses, etc) can proper catalyst operation and prevent possible catalyst provide a measure of protection in the case of engine damage.
Page 368 368 MAINTAINING YOUR VEHICLE NOTE: Intentional tampering with emissions control To minimize the possibility of catalytic converter dam- systems can result in civil penalties being assessed age: against you. • Do not shut off the engine or interrupt the ignition when the transmission is in gear and the vehicle is in WARNING! motion.
Page 369: Crankcase Emission Control System
MAINTAINING YOUR VEHICLE 369 Crankcase Emission Control System WARNING! Proper operation of this system depends on freedom • Battery fluid is a corrosive acid solution and can from sticking or plugging due to deposits. As vehicle mileage builds up, the PCV valve and passages may burn or even blind you.
Page 370 370 MAINTAINING YOUR VEHICLE CAUTION! • It is essential when replacing the cables on the battery that the positive cable is attached to the positive post and the negative cable is attached to the negative post. Battery posts are marked (+) positive and negative (-) and identified on the battery case.
Page 371: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 371 Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner • Use only refrigerants and compressor lubricants should be checked and serviced by an Authorized Dealer at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 372: Power Steering Fluid Check
372 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling CAUTION! R-134a Air Conditioning Refrigerant is a hydrofluorocar- bon (HFC) that is endorsed by the Environmental Pro- Do not use Automatic Transmission Fluid (ATF) or tection Agency and is an ozone-saving product. How- other types of power steering fluids when servicing ever, the manufacturer recommends that air conditioning the power steering system of this vehicle.
Page 373: Body Lubrication
MAINTAINING YOUR VEHICLE 373 Body Lubrication WARNING! Locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be Fluid level should be checked on a level surface with lubricated periodically to assure quiet, easy operation the engine off to prevent injury from moving parts, and to protect against rust and wear.
Page 374: Windshield Wiper Blades
374 MAINTAINING YOUR VEHICLE Windshield Wiper Blades The fluid reservoir for the windshield washers and the The rubber edges of the wiper blades and the windshield rear window washer is shared. It is located in the front of should be cleaned periodically with a sponge or soft cloth the engine compartment (on the driver side), and should and a mild nonabrasive cleaner to remove accumulations be checked for fluid level at regular intervals.
Page 375: Exhaust System
MAINTAINING YOUR VEHICLE 375 Exhaust System Cooling System The best protection against carbon monoxide entry into WARNING! the vehicle body is a properly maintained engine exhaust system. You or others can be badly burned by hot antifreeze/ If you notice a change in the sound of the exhaust system; coolant or steam from your radiator.
Page 376 376 MAINTAINING YOUR VEHICLE Check the engine cooling system hoses for brittle rubber, Cooling System — Drain, Flush, And Refill cracking, tears, cuts, and tightness of the connection at At the intervals shown in the appropriate “Maintenance the coolant recovery bottle and radiator. Inspect the Schedule,”...
Page 377 MAINTAINING YOUR VEHICLE 377 Adding Coolant CAUTION! Your vehicle has been built with an improved antifreeze/ coolant that allows extended maintenance intervals. This Mixing of antifreeze/coolant other than the specified antifreeze/coolant can be used up to 5 Years or 100,000 HOAT antifreeze/coolant may result in decreased miles before replacement.
Page 378 378 MAINTAINING YOUR VEHICLE Use only high purity water such as distilled or deionized The cap should be inspected and cleaned if there is any water when mixing the water/antifreeze (coolant) solu- accumulation of foreign material on the sealing surfaces. tion.
Page 379 MAINTAINING YOUR VEHICLE 379 The radiator normally remains completely full, so there is Disposal of Used Engine Coolant Used ethylene glycol-based antifreeze/coolant is a regu- not need to remove the radiator cap unless checking for lated substance requiring proper disposal. Check with antifreeze/coolant freeze point or replacing antifreeze/ your local authorities to determine the disposal rules for coolant.
Page 380: Hoses And Vacuum/Vapor Harnesses
380 MAINTAINING YOUR VEHICLE • Make sure that the radiator and coolant recovery If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be bottle hoses are not kinked or obstructed. safely driven. The vapor will soon dissipate. •...
Page 381: Fuel System Connections
MAINTAINING YOUR VEHICLE 381 Pay particular attention to the hoses nearest to high heat You are urged to use only the manufactures-specified sources such as the exhaust manifold. Inspect hose rout- tubes, connections and clamps, or their equivalent in ing to be sure hoses do not touch any heat source or material and specification, in any fuel system servicing.
Page 382 382 MAINTAINING YOUR VEHICLE Brake and Power Steering System Hoses NOTE: Inspection of brake hoses should be done when- When servicing the vehicle for scheduled maintenance, ever the brake system is serviced and every engine oil inspect surface of hoses for evidence of heat and me- change.
Page 383 MAINTAINING YOUR VEHICLE 383 Be sure to clean the top of the master cylinder area before WARNING! removing the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake Overfilling the brake fluid reservoir can result in fluid reservoir.
Page 384: Front/Rear Axle Fluid
384 MAINTAINING YOUR VEHICLE Front/Rear Axle Fluid Transfer Case Front Axle Fluid Level Check Fluid Level Check Lubricant should be to the bottom of the oil fill hole. Inspect the transfer case for fluid leaks. If a fluid leak is found, the transfer case fluid level can be checked by Rear Axle Fluid Level Check removing the filler plug located on the back side of the...
Page 385: Automatic Transmission
MAINTAINING YOUR VEHICLE 385 CAUTION! CAUTION! When installing plugs, do not overtighten. You could Using a transmission fluid other than the manufac- damage them and cause them to leak. turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder.
Page 386 386 MAINTAINING YOUR VEHICLE Check the fluid level while the transmission is at normal 6. Remove the dipstick again and note the fluid level on operating temperature. This occurs after at least 15 miles both sides. The fluid level should be between the “HOT” (25 km) of driving.
Page 387 MAINTAINING YOUR VEHICLE 387 Special Additives CAUTION! The manufacturer recommends against the addition of any additives to the transmission. Exception to this Be aware that if the fluid temperature is below 50°F policy is the use of special dyes to aid in detecting fluid (10°C) it may not register on the dipstick.
Page 388: Appearance Care And Protection From Corrosion
388 MAINTAINING YOUR VEHICLE Service Manual. Also check for accumulations of vegeta- passable in snow and ice, and those that are sprayed on tion or brush that could become a fire hazard, or conceal trees and road surfaces during other seasons, are highly damage to fuel lines, brake hoses, axle pinion seals, and corrosive to the metal in your vehicle.
Page 389 MAINTAINING YOUR VEHICLE 389 Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- Do not use abrasive or strong cleaning materials hicle in the shade using Mopar Car Wash or a mild such as steel wool or scouring powder, which will car wash soap, and rinse the panels completely with scratch metal and painted surfaces.
Page 390 390 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, Wheel and Wheel Trim Care touch them up immediately. The cost of such repairs is All wheels and wheel trim, especially aluminum and considered the responsibility of the owner. chrome plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion.
Page 391 MAINTAINING YOUR VEHICLE 391 Leather Seat Care & Cleaning WARNING! Mopar Total Clean is specifically recommended for leather upholstery. Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in Your leather upholstery can be best preserved by regular closed areas they may cause respiratory harm.
Page 392 392 MAINTAINING YOUR VEHICLE Glass Surfaces 2. Dry with a soft tissue. All glass surfaces should be cleaned on a regular basis Seat Belt Maintenance with Mopar Glass Cleaner or any commercial Do not bleach, dye or clean the belts with chemical household-type glass cleaner.
Page 393: Fuse Panel
MAINTAINING YOUR VEHICLE 393 FUSE PANEL Cartridge Mini Cavity Description Fuse Fuse Interior Fuses 30 Amp Audio Amp (B+) The fuse panel is on the lower instrument panel just to Green the left of the steering column. 15 Amp Sunroof (B+) Blue 10 Amp Htd Mirror (EBL)
Page 394 394 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 20 Amp Pwr Outlet (B+) 10 Amp Door Mods, Mem. Yellow Sw, O/H Lamps, IP Courtesy Lamps, 10 Amp Final Drive Control Glove Box Lamp (B+) Module (FDCM), Heater Ventilation, 10 Amp...
Page 395 MAINTAINING YOUR VEHICLE 395 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Spare 10 Amp Power Distribution (R/S) Center (PDC) Relays, Final Drive Control 10 Amp Sentry Key Remote Module (FDCM), Entry Module Front Control Module (SKREEM), Cluster (FCM) (R/S), A580 (R/S)
Page 396: Underhood Fuses (Power Distribution Center)
396 MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Cartridge Mini Cavity Description Fuse Fuse 40 Amp HVAC Blower Green 30 Amp Power Outlets Pink 30 Amp Rr Wiper/Ign R/O Pink 30 Amp ABS Pump Pink 50 Amp Cabin Htr 1 (Diesel Only) 50 Amp Auto Shut Down...
Page 397 MAINTAINING YOUR VEHICLE 397 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 40 Amp Pwr Liftgate (XK Spare Green Only) 20 Amp EATX/AC Clutch 40 Amp Starter/Junction Yellow Green Block (JB) Power 20 Amp Ign Sw 30 Amp Cig Ltr/T-Tow Yellow...
Page 398: Underhood Fuses (Integrated Power Module)
398 MAINTAINING YOUR VEHICLE Underhood Fuses (Integrated Power Module) Cartridge Mini Cavity Description Fuse Fuse 20 Amp Final Drive Control Yellow Module (FDCM) 15 Amp Powertrain Control Blue Module (PCM) Auto Shut Down (ASD) (Diesel Only) 15 Amp Brake/Stop Lamps Blue 25 Amp Next Generation Con-...
Page 399 MAINTAINING YOUR VEHICLE 399 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 10 Amp Lt Park Lamps 20 Amp Rear Wiper Yellow 10 Amp Trailer-Tow Park 20 Amp Front Control Module Lamps Yellow (FCM) Batt #1 10 Amp Rt Park Lamps 20 Amp...
Page 400: Vehicle Storage
400 MAINTAINING YOUR VEHICLE VEHICLE STORAGE Cartridge Mini Cavity Description If you are leaving your vehicle dormant for more than 21 Fuse Fuse days you may want to take steps to protect your battery. 20 Amp Ignition Off Draw You may: Yellow (IOD) #2 •...
Page 401: Replacement Bulbs
MAINTAINING YOUR VEHICLE 401 REPLACEMENT BULBS Exterior Lights Bulb Type Backup Lights ......3057K Interior Lights Bulb Type Front Fog Lights .
Page 402: Fluids And Capacities
402 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES U.S. Metric 21 Gallons 79 Liters Fuel (Approximate) Engine Oil with Filter 3.7 Liter Engine (SAE 5W-20, API Certified) 5 Qts 4.7 Liters 4.7 Liter Engine (SAE 5W-20, API Certified) 6 Qts 5.7 Liters 5.7 Liter Engine (SAE 5W-20, API Certified) 7 Qts 6.6 Liters...
Page 403: Fluids, Lubricants, And Genuine Parts
MAINTAINING YOUR VEHICLE 403 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) Engine Oil (3.7L/4.7L/5.7L Engines) Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of DaimlerChrysler Material Standard MS-6395.
Page 404: Chassis
404 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Mopar ATF+4 Automatic Transmission Fluid Transfer Case (3.7L Engines) Mopar ATF+4 Automatic Transmission Fluid Transfer Case (4.7L/5.7L Engines) Mopar NV 247/245 Transfer Case Lubricant Axle Differential (Front-Rear) Mopar Synthetic Gear &...
Page 405 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..406 Schedule “B” ......409 Maintenance Schedules .
Page 406: Emission Control System Maintenance
406 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The “Scheduled” maintenance services, listed in bold There are two maintenance schedules that show the type must be done at the times or mileages specified to required service for your vehicle. assure the continued proper functioning of the emission First is Schedule B .
Page 407 MAINTENANCE SCHEDULES 407 • Taxi, police, or delivery service (commercial service) Use the schedule that best describes your driving condi- tions. Where time and mileage are listed, follow the • Off-road or desert driving interval that occurs first. NOTE: Most vehicles are operated under the conditions listed for Schedule “B.”...
Page 408 408 MAINTENANCE SCHEDULES • Inspect brake hoses. Once a Month • Check the tire pressure and look for unusual wear or • Check the engine coolant/anti-freeze level, hoses, and damage. clamps. • Inspect the battery and clean and tighten the terminals •...
Page 409: Schedule "B" 409
SCHEDULE “B” 409 • Taxi, police, or delivery service (commercial service) Schedule “B” Follow this schedule if you usually operate your vehicle • Off-road or desert driving under one or more of the following conditions. • If equipped for and operated with E-85 (ethanol) •...
Page 410 410 SCHEDULE “B” Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 411 SCHEDULE “B” 411 Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 412 412 SCHEDULE “B” Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 413 SCHEDULE “B” 413 Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary.
Page 414 414 SCHEDULE “B” Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 415 SCHEDULE “B” 415 Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 416 416 SCHEDULE “B” Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 417 SCHEDULE “B” 417 Miles 108,000 111,000 114,000 117,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, replace if necessary.
Page 418 418 SCHEDULE “B” Miles 123,000 126,000 129,000 132,000 135,000 (Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 419 SCHEDULE “B” 419 Miles 138,000 141,000 144,000 147,000 150,000 (Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 420 420 SCHEDULE “B” Inspection and service should also be performed anytime * This maintenance is not required if the belt was a malfunction is observed or suspected. Retain all re- previously replaced. ceipts. This maintenance is recommended by the manufac- turer to the owner, but is not required to maintain emissions warranty.
Page 421: Schedule "A" 421
SCHEDULE “A” 421 Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [12] [18] [24] [30] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage.
Page 422 422 SCHEDULE “A” Miles 36,000 42,000 48,000 54, 000 (Kilometers) (60 000) (70 000) (80 000) (90 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the brake linings.
Page 423 SCHEDULE “A” 423 Miles 60,000 66,000 72,000 78,000 (Kilometers) (100 000) (110 000) (120 000) (130 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if nec- essary.
Page 424 424 SCHEDULE “A” Miles 84,000 90,000 96,000 102, 000 (Kilometers) (140 000) (150 000) (160 000) (170 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if nec- essary.
Page 425 SCHEDULE “A” 425 Miles 108,000 114,000 120,000 126,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) [Months] [108] [114] [120] [126] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if nec- essary.
Page 426 426 SCHEDULE “A” Miles 132,000 138,000 144,000 150,000 (Kilometers) (220 000) (230 000) (240 000) (250 000) [Months] [132] [138] [144] [150] Change the engine oil and engine oil filter. Rotate the tires. Check spare tire for proper pressure and correct stowage. Inspect the engine air cleaner filter, and replace if nec- essary.
Page 427 SCHEDULE “A” 427 Inspection and service should also be performed anytime WARNING! a malfunction is observed or suspected. Retain all re- ceipts. You can be badly injured working on or around a motor vehicle. Do only that service work for which This maintenance is recommended by the manufac- you have the proper equipment.
Page 429: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Reporting Safety Defects ....433 Vehicle ......430 In Canada .
Page 430: Suggestions For Obtaining Service For Your Vehicle
Warranty service must be done by an authorized or work done that is not on your maintenance log, let the Chrysler, Dodge, or Jeep dealer. We strongly recommend service advisor know. that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 431 IF YOU NEED CONSUMER ASSISTANCE 431 • Vehicle identification number technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely • Vehicle delivery date and mileage manner. DaimlerChrysler Motors Corporation Customer Center This is why you should always talk to your dealer’s P.O.
Page 432 432 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech contract, call the manufacturer’s Service Contract Na- Impaired (TDD/TTY) tional Customer Hotline at 1-800-521-9922. To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
Page 433: Warranty Information (U.s. Vehicles Only)
IF YOU NEED CONSUMER ASSISTANCE 433 campaign. However, NHTSA cannot become involved in WARRANTY INFORMATION (U.S. Vehicles Only) See the Warranty Information Booklet for the terms and individual problems between you, your dealer, and the provisions of DaimlerChrysler’s warranties applicable to manufacturer.
Page 434: Publication Order Forms
434 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals. PUBLICATION ORDER FORMS To order the following manuals, you may use either the Filled with diagrams, charts and detailed illustrations, website or the phone numbers listed below. Visa, Mas- these practical manuals make it easy for students and tercard, American Express, and Discover orders are ac- technicians to find and fix problems on computer- cepted.
Page 435: Department Of Transportation Uniform Tire Quality Grades
IF YOU NEED CONSUMER ASSISTANCE 435 Call Toll Free at: Treadwear The treadwear grade is a comparative rating based on the • 1–800–890–4038 (U.S.) wear rate of the tire when tested under controlled con- • 1–800–387–1143 (Canada) ditions on a specified government test course. For ex- ample, a tire graded 150 would wear one and a half (1 1/2) times as well on the government course as a tire Visit us on the World Wide Web at:...
Page 436: Temperature Grades
436 IF YOU NEED CONSUMER ASSISTANCE Vehicle Safety Standard No. 109. Grades B and A repre- WARNING! sent higher levels of performance on the laboratory test wheel than the minimum required by law. The traction grade assigned to this tire is based on straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or WARNING!
Page 437 INDEX...
Page 438 438 INDEX ABS (Anti-Lock Brake System) ... . 177,275 Alignment and Balance ....294 Adding Fuel .
Page 439 INDEX 439 Special Additives ..... . 387 Master Cylinder ..... . . 382 Torque Converter .
Page 440 440 INDEX Caution, Exhaust Gas ..... 152 Contract, Service ......432 CD (Compact Disc) Player .
Page 441 INDEX 441 Data Recorder, Event ..... . 55 Drive Belts ......365 Daytime Running Lights .
Page 442 442 INDEX Jump Starting ......348 Oil Selection ......402 Tow Hooks .
Page 443 INDEX 443 Finish Care ......389 Fluids, Lubricants and Genuine Parts ..403 Flashers .
Page 444 444 INDEX System Hoses ......381 Gross Axle Weight Rating ....320 Tank Capacity .
Page 445 INDEX 445 HomeLink (Garage Door Opener) Transmitter . . . 151 Interior Lighting ......125 Hood Release ......118 Interior Lights .
Page 446 446 INDEX LATCH Dimmer Switch, Headlight ... . . 119,124 (Lower Anchors and Tether for CHildren) ..61,63 Electronic Stability Program (ESP) Lead Free Gasoline ..... . 307 Indicator .
Page 447 INDEX 447 Passing ......124 Power Door ......27 Reading .
Page 448 448 INDEX Mini-Trip Computer ..... . 193 Occupant Restraints ..... . . 37 Mirrors .
Page 449 INDEX 449 Onboard Diagnostic System ....358,359 Phone, Hands-Free (UConnect™) ... . . 80 Opener, Garage Door (HomeLink ) ... 151 Placard, Tire and Loading Information .
Page 450 450 INDEX Programming Transmitters Rear Seat, Folding ..... 108,111 (Remote Keyless Entry) ....153,157 Rear Window Defroster .
Page 451 INDEX 451 Restraints, Child ......57 Child Restraint ..... . . 57,65 Restraints, Occupant .
Page 452 452 INDEX Reclining ......104 Snow Chains (Tire Chains) ....295 Seatback Release .
Page 453 INDEX 453 Steering Wheel Mounted Sound System Tire Identification Number (TIN) ... . . 283 Controls ......230 Tire Markings .
Page 454 454 INDEX Rotation ......296 Cooling System Tips ....332 Safety .
Page 455 INDEX 455 Turn Signals ......124,176 Warnings and Cautions ..... 8 Warranty Information .
Page 456 456 INDEX Wipers, Intermittent ..... . 127 Wipers, Rain Sensitive ....128 Wiring, Ignition (Spark Plug Wires) .

This manual is also suitable for:

Commander

Jeep Automobile Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

INTRODUCTION

Chapters

Related Manuals for Jeep Automobile

Summary of Contents for Jeep Automobile