Download Print this page

Jeep Automobile Owner's Manual

Chrysler llc

Hide thumbs Also See for Automobile:

Owner's manual (478 pages)

,

Warranty information booklet (48 pages)

,

Service and warranty handbook (42 pages)

page of 400

/ 400
Contents
Table of Contents
Bookmarks

Table of Contents

Advertisement

Quick Links

Download this manual See also: Manual and Warranty, Owner's Manual

SECTION

1

INTRODUCTION

2

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

4

UNDERSTANDING YOUR INSTRUMENT PANEL

5

STARTING AND OPERATING

6

WHAT TO DO IN EMERGENCIES

7

MAINTAINING YOUR VEHICLE

8

MAINTENANCE SCHEDULES

9

IF YOU NEED CONSUMER ASSISTANCE

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 377

INDEX

TABLE OF CONTENTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 231

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 291

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 349

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 369

PAGE

1

2

3

4

5

6

7

8

9

10

Table of Contents

Advertisement

Chapters

Table of Contents

Need help?

Need help?

Do you have a question about the Automobile and is the answer not in the manual?

Questions and answers

Summary of Contents for Jeep Automobile

Page 1: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 3: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Warnings And Cautions ....8 Roll Over Warning .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION Roll Over Warning Thank you for selecting a Jeep Grand Cherokee SRT8 Utility vehicles have a significantly higher roll over rate and welcome to our worldwide family. than other types of vehicles. This vehicle has a higher ground clearance, higher center of gravity, and narrower Before you start to drive this vehicle, read this manual.
Page 5 INTRODUCTION 5 million annually. In a roll over crash an unbelted person is significantly more likely to die than a person wearing a seat belt. Always buckle up. This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle.
Page 6: How To Use This Manual
6 INTRODUCTION When it comes to service, remember that your authorized HOW TO USE THIS MANUAL dealer knows your vehicle best, has the factory-trained Consult the table of contents to determine which section technicians and genuine Mopar parts, and is interested contains the information you desire.
Page 7 INTRODUCTION 7...
Page 8: Warnings And Cautions
8 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 9: Vehicle Modifications / Alterations
INTRODUCTION 9 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....14 To Set The Alarm ..... .18 Ignition Key Removal .
Page 12 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transmitter Battery Service ....23 Lap/Shoulder Belt Operating Instructions ..36 Remote Starting System — If Equipped ..24 Adjustable Upper Shoulder Belt Anchorage .
Page 13: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Safety Checks You Should Make Inside The Safety Checks You Should Make Outside The Vehicle ......66 Vehicle .
Page 14: A Word About Your Keys
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The keys for your new vehicle are enclosed in a plastic Place the shift lever in P (Park). Turn the ignition switch bag with the key code number on it. If you received your to the OFF position, and remove the key.
Page 15: Key-In-Ignition Reminder
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 Key-In-Ignition Reminder WARNING! If the driver’s door is opened when the key is in the ignition and not turned to the ON position, a chime will Leaving children in a vehicle unattended is danger- sound to remind you to remove the key.
Page 16: Important Note About Service
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE light will come on for 3 seconds immediately after the with remote starting systems. Use of these systems ignition switch is turned on for a bulb check. Afterwards, may result in vehicle starting problems and loss of if the bulb remains on, this indicates a malfunction in the security protection.
Page 17: Replacement Keys
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Replacement Keys Customer Key Programming NOTE: Only keys that have been programmed to the You can program new keys to the system if you have two vehicle electronics can be used to start the vehicle. Once valid keys by doing the following: a Sentry Key has been programmed to a vehicle, it cannot 1.
Page 18: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Insert a blank Sentry Key into the ignition switch and SECURITY ALARM SYSTEM — IF EQUIPPED turn the ignition switch ON within 60 seconds. After 10 This system monitors the vehicle doors, liftgate, liftgate seconds, a single chime will sound.
Page 19: To Disarm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 the door lock plunger located on the inside of the doors the system. The Security Alarm System will not disarm or with the driver’s door key lock cylinder, will not set with a manual unlock, either through the lock plunger the alarm.
Page 20: To Unlock The Doors
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the key is in the ignition switch, then all buttons on that transmitter will be disabled. The buttons on the remaining transmitters will work. If the vehicle is shifted out of P (Park), all the transmitter buttons are disabled for all keys.
Page 21: To Lock The Doors
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: If desired, the system can be programmed to Customer Programmable Features of the “Electronic Ve- unlock all doors on the first press of the “Unlock” button. hicle Information Center (EVIC)” section or by following Refer to “Remote Unlock Driver’s Door 1st”...
Page 22: Using The Panic Alarm
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The interior lights will turn off when the ignition WARNING! is switched to the ACC or ON position after the panic alarm is activated. However, the exterior lights and horn Driving with the flipper glass open can allow poi- will remain on.
Page 23: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 2. While the “Unlock” button is pressed, (after 4 seconds) If your Remote Keyless Entry transmitter fails to operate press the “Lock” button. Release both buttons. from a normal distance, check for these two conditions. The “Flash Lights On Lock/Unlock”...
Page 24: Things To Know Before Starting Your Vehicle 11
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. With the transmitter buttons facing down, remove the 2. Remove and replace the battery. Avoid touching the small screw, and separate the two halves of the transmit- new battery with your fingers. Skin oils may cause ter.
Page 25 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 To remote start your vehicle, press the “Lock” button on Once the vehicle has started, the engine will run for 15 the key fob once, then within three seconds press the minutes. To cancel remote start, press the “Remote Start” “Remote Start”...
Page 26: Door Locks
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The vehicle can be started remotely up to a maximum of WARNING! two times. The vehicle is also allowed a maximum of one • For personal security and safety in the event of an failed start, where the remote start sequence was initiated but cancelled before the engine begins to crank.
Page 27 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 The rear doors cannot be opened from inside the vehicle until you pull up the lock plungers. Automatic Door Locks If this feature is selected your door locks will lock automatically if the vehicle speed is above 15 mph (24 km/h) and all doors are closed.
Page 28: Child Protection Door Lock
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Protection Door Lock The rear doors of your vehicle are equipped with child protection locks. If you push up on the lever on the open edge of the door it cannot be opened from the inside of the vehicle.
Page 29: Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 WINDOWS Power Windows The power window controls are located on the driver’s door trim panel. There is a single switch on the front passenger door/rear doors which operates the front passenger/rear passenger door windows. The window controls will operate only when the ignition switch is in the ON or ACCESSORY position.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down Auto Up Feature with Anti-Pinch Protection Both the driver and front passenger window switch has (Driver’s and Front Passenger Door Only) an “Auto Down” feature. Press the window switch past Lift the window switch to the second detent, release, and the first detent, release, and the window will go down the window will go up automatically.
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! There is no anti-pinch protection when the window is almost closed. Be sure to clear all objects from the window before closing. Resetting the Auto-Up Feature Should the Auto-Up feature stop working the window probably needs to be reset.
Page 32: Wind Buffeting
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions.
Page 33: Liftgate Flipper Glass
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 WARNING! Driving with the liftgate open can allow poisonous exhaust gases into your vehicle. You and your pas- sengers could be injured by these fumes. Keep the liftgate closed when you are operating the vehicle. Liftgate Flipper Glass The liftgate flipper glass is also unlocked when the liftgate is unlocked.
Page 34: Occupant Restraints
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once the liftgate flipper glass has been opened, connec- OCCUPANT RESTRAINTS tion to the rear window wiper is interrupted, preventing Some of the most important safety features in your activation of the rear wiper blade while the flipper glass vehicle are the restraint systems.
Page 35: Lap/Shoulder Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Research has shown that seat belts save lives, and they WARNING! can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown In a collision, you and your passengers can suffer from the vehicle.
Page 36: Lap/Shoulder Belt Operating Instructions
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions WARNING! 1. Enter the vehicle and close the door. Sit back and • Wearing a seat belt incorrectly is dangerous. Seat adjust the seat. belts are designed to go around the large bones of 2.
Page 37 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Latch Plate Latch Plate To Buckle 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”...
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap portion, pull up a bit on the shoulder belt. To loosen the lap belt if it is too A belt that is buckled into the wrong buckle will not protect you properly.
Page 39 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 5. Position the shoulder belt on your chest so that it is 6. To release the belt, push the red button marked PRESS comfortable and not resting on your neck. The retractor on the buckle.
Page 40: Adjustable Upper Shoulder Belt Anchorage
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage As a guide, if you are shorter than average, you will In the front seating positions, the shoulder belt can be prefer a lower position, and if you are taller than average, adjusted upward or downward to position the belt away you’ll prefer a higher position.
Page 41: Energy Management Feature
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 3. Allow the belt to retract. As the belt retracts, you will WARNING! hear a clicking sound. This indicates the safety belt is • The belt and retractor assembly must be replaced now in the automatic locking mode.
Page 42: Seat Belts And Pregnant Women
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: These devices are not a substitute for proper seat Seat Belt Extender belt placement by the occupant. The seat belt must still be If a seat belt is too short, even when fully extended and worn snugly and positioned properly.
Page 43: Driver And Front Passenger Supplemental Restraint Systems (Srs)
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Driver And Front Passenger Supplemental This vehicle has airbags for both the driver and right Restraint Systems (SRS) front passenger as a supplement to the seat belt restraint systems. The driver’s front airbag is mounted in the steering wheel.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This vehicle is equipped with window bags to protect the WARNING! driver, front, and rear passengers sitting next to a win- • dow. They are located above the side windows. Their Do not put anything on or around the front airbag covers are also labeled SRS/AIRBAG.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 NOTE: Do not use a clothing bar mounted to the coat The window bag on the crash side of the vehicle is hooks in this vehicle. A clothing bar will impede the triggered in moderate to severe side collisions.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children that are not big enough to properly wear the 3. The driver and front passenger seats should be moved vehicle seat belt should be secured in the rear seat, in a back as far as practical to allow the front airbags room to child restraint or belt-positioning booster seat.
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 Airbag System Components WARNING! The airbag system consists of the following: • Relying on the airbags alone could lead to more • Occupant Restraint Control Module severe injuries in a collision. The airbags work •...
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How The Airbag System Works Also, the ORC turns on the “Airbag Warning Light” for 6 to 8 seconds for a self-check • The Occupant Restraint Control (ORC) Module de- when the ignition is first turned on. After the termines if a frontal, side, or rollover collision is severe self-check, the “Airbag Warning Light”...
Page 49 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 • The Driver and Passenger Airbag/Inflator Units are • The Side Impact SRS Side Curtain Airbags are de- located in the center of the steering wheel and the right signed to activate only in certain side or rollover side of the instrument panel.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs They are not permanent and normally heal quickly. The airbag system is designed to deploy when the However, if you haven’t healed significantly within a Occupant Restraint Control (ORC) Module detects a few days, or if you have any blistering, see your doctor moderate-to-severe frontal collision, to help restrain the immediately.
Page 51 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Maintaining Your Airbag System WARNING! Deployed airbags and seat belt pretensioners cannot WARNING! protect you in another collision. Have the airbags, • Modifications to any part of the airbag system seat belt pretensioners, and seat belt retractor assem- bly, replaced by an authorized dealer as soon as could cause it to fail when you need it.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Warning Light data gathered during a complete accident investigation, You will want to have the airbag system ready to inflate the electronic data may be used by DaimlerChrysler for your protection in an impact. The airbag system is Corporation and others to learn more about the possible designed to be maintenance free.
Page 53 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 provided to the custodial entity upon request. General Data Parameters that May Be Recorded: data that does not identify particular vehicles or crashes • Diagnostic trouble code(s) and warning lamp status may be released for incorporation in aggregate crash for electronically-controlled safety systems, including databases, such as those maintained by the US govern- the airbag system...
Page 54: Child Restraint
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child Restraint WARNING! Everyone in your vehicle needs to be buckled up all the time — babies and children, too. Every state in the United In a collision, an unrestrained child, even a tiny States and all Canadian provinces require that small baby, can become a missile inside the vehicle.
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 • The infant carrier is only used rearward-facing in the WARNING! vehicle. It is recommended for children who weigh up • Improper installation can lead to failure of an to about 20 lbs (9 kg). “Convertible” child seats often have a higher weight limit in the rearward-facing infant or child restraint.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child Both types of seat belts are designed to keep the lap restraint: portion tight around the child restraint so that it is not necessary to use a locking clip.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 • In the rear seat, you may have trouble tightening the Do not leave it loose in the vehicle. In a sudden stop or lap/shoulder belt on the child restraint because the collision, it could strike the occupants or seat backs buckle or latch plate is too close to the belt path and cause serious personal injury.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the shoulder belt contacts the face or neck, move the with knees bent over the vehicle’s seat cushion while the child’s back is against the seat back, they should use a child closer to the center of the vehicle.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 belts. Child restraints having tether straps and hooks for Remind all children in the vehicle that the seat belts are connection to the top tether anchorages have been avail- not toys and should not be played with, and never leave able for some time.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the vehicle’s seat belts. Please refer to the next section for typical installation instructions. Installing the LATCH-Compatible Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Not all child restraint systems will be installed as described here.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 In addition, there are tether strap anchorages behind each means of adjusting the tension in the strap. Forward- rear seating position located on the back of the seat. facing toddler restraints and some rear-facing infant restraints will also be equipped with a tether strap, a hook for attachment to the tether strap anchorage and a means of adjusting the tension of the strap.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If the seat belt has a automatic locking retractor, it will WARNING! have a distinctive label. Pull the belt from the retractor until there is enough to allow you to pass through the Improper installation of a child restraint to the child restraint and slide the latch plate into the buckle.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 If the belt still can’t be tightened, or if by pulling and pushing on the restraint loosens the belt, you may need to do something more. Disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again.
Page 64: Engine Break-In Recommendations
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ENGINE BREAK-IN RECOMMENDATIONS WARNING! A long break-in period is not required for the engine in your new vehicle. An incorrectly anchored tether strap could lead to increased head motion and possible injury to the Drive moderately during the first 300 miles (500 km).
Page 65: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • Do not inhale exhaust gases. They contain carbon A new engine may consume some oil during its first few thousand miles (kilometers) of operation. This should be monoxide, a colorless and odorless gas which can kill. considered as a normal part of the break-in and not Never run the engine in a closed area, such as a interpreted as an indication of difficulty.
Page 66: Vehicle
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Airbag Warning Light Vehicle The light should come on and remain on for 6 to 8 seconds as a bulb check when the ignition switch is first Seat Belts turned on.
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Safety Checks You Should Make Outside The Lights Vehicle Have someone observe the operation of all exterior lights while you work the controls. Check turn signal and high Tires beam indicator lights on the instrument panel. Examine tires for excessive tread wear or uneven wear patterns.
Page 69 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......74 Hands–Free Communication (UConnect™) — If Equipped .
Page 70 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Seat Adjustment — Recline ..101 To Open And Close The Hood ... . . 112 Manual Lumbar Support Adjustment .
Page 71 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 71 High Beam Switch ....119 To Set At a Desired Speed ....128 Passing Light .
Page 72 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ESP/BAS Warning Lamp And ESP/TCS Sunglasses Storage ....145 Indicator Light ..... . . 136 Garage Door Opener .
Page 73 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 73 Venting Sunroof - Express ....154 Cargo Light ......158 Sunshade Operation .
Page 74: Mirrors
74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Automatic Dimming Mirror This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light next to the button will indicate when the dimming feature is activated.
Page 75: Outside Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 WARNING! CAUTION! Vehicles and other objects seen in the right side To avoid damage to the mirror during cleaning, convex mirror will look smaller and farther away never spray any cleaning solution directly onto the than they really are.
Page 76: Driver's Outside Automatic Dimming Mirror - If Equipped
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Outside Automatic Dimming Mirror — If Equipped If your vehicle is equipped with a driver’s outside automatic dimming mirror, it operates when the inside automatic dimming mirror is on. This outside mirror operates off the inside mirror switch and will automati- cally adjust for annoying headlight glare when the inside mirror does.
Page 77: Heated Remote Control Mirrors - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 77 Heated Remote Control Mirrors — If Equipped These mirrors are heated to melt frost or ice. This feature is activated whenever you turn on the rear window defrost. Lighted Vanity Mirrors — If Equipped To access a lighted vanity mirror, flip down one of the visors.
Page 78: Hands-Free Communication (Uconnect™)
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE HANDS–FREE COMMUNICATION (UConnect™) — The UConnect™ phonebook enables you to store up to 32 IF EQUIPPED names and four numbers per name. Each language has a UConnect™ is a voice-activated, hands-free, in- vehicle separate 32-name phonebook accessible only in that communications system.
Page 79: Operations
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 79 Headset Profile), you may not be able to use any UCon- nect™ features. Refer to your cellular service provider or the phone manufacturer for details. The UConnect™ system is fully integrated with the vehicle’s audio system.
Page 80 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Prior to giving a voice command, one must wait for Voice Command Tree the voice on beep, which follows the Ready prompt Refer to “Voice Tree” at the end of this section. or another prompt.
Page 81 NOTE: • www.chrysler.com/uconnect • For identification purposes, you will be prompted to give the UConnect™ system a name for your cellular • www.dodge.com/uconnect phone. Each cellular phone that is paired should be • www.jeep.com/uconnect given a unique phone name.
Page 82 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked to give your cellular phone a Call/Dial by Saying a Number priority level between 1 and 7, 1 being the highest • Press the ’Phone’ button to begin. priority.
Page 83 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 • System will prompt you to say the name of the person • After the Ready prompt and the following beep, say you want call. Phonebook New Entry. • After the Ready prompt and the following beep, say •...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When prompted, recite the new phone number for the The UConnect™ system will allow you to enter up to 32 names in the phonebook with each name having up to phonebook entry that you are editing. four associated phone numbers and designations.
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 • After the Ready prompt and the following beep, say After confirmation, the phonebook entries will be de- Phonebook Delete. leted. Note that only the phonebook in the current language is deleted. • After you enter the Phonebook Delete menu, you will then be asked for the name of the entry that you wish Delete All Entries in the UConnect™...
Page 86: Phone Call Features
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect™ system will play the names of all the Answer or Reject an Incoming Call - No Call phonebook entries. Currently in Progress When you receive a call on your cellular phone, the •...
Page 87 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Making a Second Call while Current Call in indicating that the active and hold status of the two calls Progress have switched. Only one call can be placed on hold at one To make a second call while you are currently in a call, time.
Page 88: Uconnect™ System Features
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • After ignition key is switched off, a call can continue Call Termination To end a call in progress, momentarily press the Phone’ on the UConnect™ system either until the call ends or button.
Page 89 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 • After the Ready prompt and the following beep, say If the phone is not reachable and the UConnect™ system the name of the language you wish to switch to is operational, you may reach the emergency number as (English, Espanol, or Francais, if so equipped).
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your phone must be turned on and paired to the UCon- Paging nect™ system to allow use of this vehicle feature in To learn how to page, refer to Working with Automated emergency situations when the cell phone has network Systems.
Page 91 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 When calling a number with your UConnect™ system Turning Confirmation Prompts On/Off that normally requires you to enter in a touch-tone Turning confirmation prompts off will stop the system sequence on your cellular phone keypad, you can push from confirming your choices (e.g., the UConnect™...
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using the Cellular Phone Keypad Mute/Un-mute (Mute off) You can dial a phone number with your cellular phone When you mute the UConnect™ system, you will still be keypad and still use the UConnect™ system (while able to hear the conversation coming from the other dialing via the cell phone keypad, the user must exercise party, but the other party will not be able to hear you.
Page 93: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Information Service If you would like to connect or disconnect the Blue- When using AT&T Wireless Service, dialing to phone tooth™ connection between a UConnect™ paired cellular number #121, you can access voice activated automated phone and the UConnect™...
Page 94: Things You Should Know About Your Uconnect™ System
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Select another Cellular Phone Delete UConnect™ Paired Cellular Phones This feature allows you to select and start using another • Press the ’Phone’ button to begin. phone with the UConnect™ system. The phone must •...
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • Speak normally, without pausing, just as you would • When navigating through an automated system, such speak to a person sitting approximately eight (8) feet as voice mail, or when sending a page at the end of away from you.
Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Echo at far end can sometime be reduced by lowering Far End Audio Performance the in-vehicle audio volume. • Audio quality is maximized under: Bluetooth Communication Link • low-to-medium blower setting, Occasionally, Cellular phones have been found to lose •...
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97...
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99...
Page 100: Seats
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE SEATS North American English Primary Alternate(s) Front Manual Seat Adjustment Move the seat forward or rearward using the adjustment Zero bar. Lift up on the bar located on the front of the seat near Add location Add new the floor.
Page 101: Front Seat Adjustment - Recline
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Front Seat Adjustment — Recline WARNING! To adjust the seatback, lift the lever located on the • It is extremely dangerous to ride in a cargo area, outboard side of the seat, lean back, and release the lever at the desired position.
Page 102: Manual Lumbar Support Adjustment
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Lumbar Support Adjustment 8 - Way Driver’s Power Seat The manual lumbar support adjustment lever is located The driver’s power seat switches are located on the on the right side of the driver’s seat and on the left side outboard side of the driver’s seat lower side trim.
Page 103: Way Passenger's Power Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 4 - Way Passenger’s Power Seat — If Equipped The front passenger’s power seat switches are located on the outboard side of the passenger seat lower side trim. The bottom switch controls forward/rearward adjust- ment.
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE center of the instrument panel. After turning on the Pressing the switch a second time will select low-level ignition, you can choose from High, Off, or Low heat heating. Pressing the switch a third time will shut the settings.
Page 105: 60/40 Split Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 NOTE: Be sure that the front seats are fully upright and WARNING! positioned forward. This will allow the rear seatback to fold down easily. Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, 1.
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Do not fold the rear seat down with the center To Raise Rear Seat seat belt buckled. Raise the rear seatback and lock it into place. If interfer- ence from the cargo area prevents the seatback from fully 2.
Page 107: Driver Memory Seat - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 Storage — Rear Seat Armrest (If Equipped) The rear seat may be equipped with a center storage armrest. Armrest Storage Bin DRIVER MEMORY SEAT — IF EQUIPPED Once programmed, the memory buttons 1 and 2 on the driver’s door panel can be used to recall the driver’s seat, Rear Seat Armrest driver’s outside mirror, adjustable brake and accelerator...
Page 108: Setting Memory Positions And Linking Remote Keyless Entry Transmitter To Memory
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Keyless Entry transmitters can also be programmed to can accommodate up to four transmitters, each one recall the same positions when the “Unlock” button is linked to either of the two memory positions. pressed.
Page 109: Memory Position Recall
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 4. Adjust the brake and accelerator pedals to the desired 10. Insert the ignition key and turn the ignition switch to positions. the ON position. 5. Turn on the radio and set the radio station presets (up 11.
Page 110: To Disable A Transmitter Linked To Memory
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To recall the memory settings for driver one, press To Disable A Transmitter Linked to Memory memory button number 1 on the driver’s door or the 1. Turn the ignition switch to the OFF position and “Unlock”...
Page 111: Easy Entry/Exit Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 NOTE: Once programmed, all transmitters linked to approximately 2.5 inches (60 mm) when the key is memory can be easily enabled or disabled at one time. placed into the ignition and turned out of the LOCK Refer to Remote Linked to Memory under Electronic position.
Page 112: To Open And Close The Hood
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Each stored memory setting will have an associated Easy TO OPEN AND CLOSE THE HOOD Entry and Easy Exit position. To open the hood, pull the release lever inside your vehicle located below the instrument panel and in front NOTE: The Easy Entry Easy Exit feature is not enabled of the driver’s door.
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Then, reach under the hood, move safety latch to the left, WARNING! and lift the hood. To prevent possible damage, do not slam the hood to close it. Use a firm downward push at If the hood is not fully latched, it could fly up when the center of the hood to ensure that both latches engage.
Page 114: Lights
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Battery Saver Feature—Exterior/Interior Lights If the multi-function control lever is left in the interior Multi-Function Control Lever light position, parking light position, or the headlight The multi-function control lever controls the operation of position when the ignition switch is moved to the OFF the headlights, turn signals, headlight beam selection, position, the battery saver feature will automatically turn...
Page 115: Headlights And Parking Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Headlights and Parking Lights Automatic Headlight System — If Equipped Turn the end of the multi-function control lever to the Turn the end of the multi-function control lever to the first detent for parking light operation. Turn to the third detent to activate the automatic headlight system.
Page 116: Smartbeams - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If your vehicle is equipped with a “Rain Sensitive Wiper and automatically switches from high beams to low System,” and it is activated, the headlights will automati- beams until the approaching vehicle is out of view. cally turn on after the wipers complete five wipe cycles NOTE: If the windshield or SmartBeam mirror is re- within approximately 1 minute, and they will turn off...
Page 117: Instrument Panel And Interior Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 To Deactivate decrease the brightness (dimmer control) of the instru- ment panel lights. Full daytime brightness on all elec- 1. Pull back on the muti-function control lever to manu- tronic displays (odometer, overhead console, radio, and ally deactivate the system (normal operation of high Automatic Climate Control (if equipped) is obtained by beams).
Page 118: Lights-On Reminder
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE until the ignition switch is turned OFF or the parking A front fog light is a lighting device providing illumina- brake is engaged. The headlight switch must be used for tion forward of the vehicle under conditions of fog, rain, normal night time driving.
Page 119: High Beam Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 High Beam Switch Headlight Time Delay Pull the multi-function control lever towards you to There is also a feature that delays turning off the vehicle switch the headlights to “High” beam. The “High Beam lights for 30, 60, or 90 seconds after the ignition switch is Indicator Light”...
Page 120: Front Map/Reading Lights
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Front Map/Reading Lights These lights are mounted in the overhead console. Each light can be turned on by pressing the recessed area of the lens. To turn these lights off, press the recessed area of the lens a second time.
Page 121: Windshield Wipers And Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 WINDSHIELD WIPERS AND WASHERS The front and rear wipers and washers are operated by a switch in the right side control lever. Turn the end of the control lever to select “Lo,” “Hi,” or one of the five speed sensitive intermittent windshield wiper speeds.
Page 122: Mist
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To use the washer, pull the lever toward you and hold Mist while spray is desired. If the lever is pulled while in the Use this feature when weather conditions make occa- delay range, the wiper will operate for several seconds sional usage of the wipers necessary.
Page 123: Rain Sensing Wipers-If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Rain Sensing Wipers—If Equipped The sensitivity of the system can be adjusted with the This feature senses moisture on the windshield and multi-function lever. Wiper delay position 1 is the least automatically activates the wipers for the driver. The sensitive, and wiper delay position 5 is the most sensi- feature is especially useful for road splash or overspray tive.
Page 124 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • A customer programmable feature in the Electronic • Low Ambient Temperature — When the ignition is Vehicle Information Center (EVIC) allows the Rain first turned ON, the rain sensing system will not Sense feature to be turned off.
Page 125: Tilt Steering Column
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 TILT STEERING COLUMN WARNING! To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as Tilting the steering wheel column while the vehicle desired.
Page 126: Adjustable Pedals - If Equipped
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ADJUSTABLE PEDALS — IF EQUIPPED This feature allows both the brake and accelerator pedals to move toward the driver to provide improved position with the steering wheel. The adjustable pedal system is designed to allow a greater range of driver comfort for steering wheel tilt and seat position.
Page 127 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Press the left side of the button to move the pedals CAUTION! rearward (toward the driver). Do not place any article under the adjustable pedal’s Press the right side of the button to move the pedals or impede its ability to move as it may cause damage forward (away from the driver).
Page 128: Electronic Speed Control
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL To Activate When engaged, this device takes over accelerator opera- Press the ON·OFF button to turn the system ON. To turn tions at speeds greater than 25 mph (40 km/h). The the system OFF, press the ON·OFF button again.
Page 129: To Resume Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 To Resume Speed To Accelerate for Passing To resume a previously set speed, press and release the Depress the accelerator as you would normally. When the RES·ACCEL button. Resume can be used at any speed pedal is released, the vehicle will return to the set speed.
Page 130: Driving Up Or Down Hills
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • When it is not possible to keep your vehicle at a set Driving Up or Down Hills When going up or down hills, it is possible for your speed. vehicle to lose or gain speed, even though the Speed •...
Page 131: Electronic Brake Control System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 ELECTRONIC BRAKE CONTROL SYSTEM WARNING! Your vehicle is equipped with an advanced electronic brake control system that includes ABS (Anti-Lock Brake ABS (Anti-Lock Brake System) cannot prevent the System), TCS (Traction Control System), BAS (Brake natural laws of physics from acting on the vehicle, Assist System), ERM (Electronic Roll Mitigation), and nor can it increase the traction afforded by prevail-...
Page 132: Tcs (Traction Control System)
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TCS (Traction Control System) BAS (Brake Assist System) The BAS is designed to optimize the vehicle’s braking This system monitors the amount of wheel spin of each of capability during emergency braking maneuvers. The the driven wheels.
Page 133: Erm (Electronic Roll Mitigation)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 ERM (Electronic Roll Mitigation) WARNING! This system anticipates the potential for wheel lift by monitoring the driver’s steering wheel input and the BAS (Brake Assist System) cannot prevent the natu- speed of the vehicle. When ERM determines that the rate ral laws of physics from acting on the vehicle, nor of change of the steering wheel angle and vehicles speed can it increase the traction afforded by prevailing...
Page 134: Esp (Electronic Stability Program)
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE the brake of the appropriate wheel to assist in counter- WARNING! acting the over/under steer condition. Engine power may also be reduced to help the vehicle maintain the Many factors, such as vehicle loading, road condi- desired path.
Page 135 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Light also flashes when TCS is active. If the ESP/TCS The ESP system has 2 available operating modes. Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as This is the normal operating mode for ESP.
Page 136: Esp/Bas Warning Lamp And Esp/Tcs Indicator Light
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn ESP on again, momentarily depress the ESP Control Off” mode by pressing the ESP switch. Once the situation Switch. This will restore the normal “ESP On” mode of requiring ESP to be switched to the “ESP Partial Off” operation.
Page 137: Rear Park Assist System- If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 after several ignition cycles, and the vehicle has been REAR PARK ASSIST SYSTEM— IF EQUIPPED driven several miles at speeds greater than 30 mph (48 The Rear Park Assist System provides visual and audible km/h), see your authorized dealer as soon as possible to indications of the distance between the rear fascia and the have the problem diagnosed and corrected.
Page 138: Rear Park Assist Sensors
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Park Assist Sensors The four Rear Park Assist Sensors, located in the rear fascia, monitor the area behind the vehicle that is within the sensors’ field of view. The monitored area seems oval in shape.
Page 139 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 When the ignition is changed to the RUN/ON position, When the detected obstacle is about 11.8 inches (30 cm) the warning display will turn ON all of its LEDs for from the rear fascia, the warning display will actuate a about 1 second.
Page 140: Enable/Disable The Rear Park Assist System
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Enable/Disable the Rear Park Assist System When the switch is pressed to disable the system, the The Rear Park Assist System can be enabled and disabled instrument cluster will display the PARK ASSIST DIS- with a switch located in the switch bank of the instru- ABLED message.
Page 141: Service The Rear Park Assist System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Service the Rear Park Assist System CAUTION! When the Rear Park Assist System is defective, the instrument cluster will actuate a single chime, once per • The Rear Park Assist System is only a parking aid ignition cycle, and it will display the SERVICE PARK and it is unable to recognize every obstacle, in- ASSIST SYSTEM message.
Page 142 142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Clean all four Rear Park Assist Sensors regularly, WARNING! taking care not to scratch or damage them. The sensors • must not be covered with ice, snow, slush, mud, dirt or Drivers must be careful when backing up even when using the Rear Park Assist System.
Page 143: Rear Camera - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 REAR CAMERA — IF EQUIPPED Turning the Rear Camera On Vehicles with a Navigation radio may be equipped with 1. To access the rear camera mode, select “Rear Camera” a rear view camera (located on the rear liftgate) that at the Systems Settings screen and press ENTER.
Page 144: Turning The Rear Camera Off
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning the Rear Camera Off OVERHEAD CONSOLE The overhead console contains courtesy/reading lights, 1. To turn the rear camera off, select “Rear Camera” at an optional universal garage door opener (HomeLink ), the Systems Settings screen and press ENTER. Refer to storage for sunglasses, and optional power sunroof your “Navigation User’s Manual”...
Page 145: Courtesy/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Courtesy/Reading Lights GARAGE DOOR OPENER The HomeLink Universal Transceiver replaces up to At the forward end of the console are two courtesy/ three remote controls (hand held transmitters) that oper- reading lights. ate devices such as garage door openers, motorized Press the lens to turn these lights on.
Page 146 146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! A moving garage door can cause injury to people and Vehicle exhaust contains carbon monoxide, a danger- pets in the path of the door. People or pets could be ous gas. Do not run the vehicle’s exhaust while seriously or fatally injured.
Page 147: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
Page 148 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Press and hold the two outer HomeLink buttons, and 2. Position the end of your hand-held transmitter 1-3 release only when the EVIC display shows “CHANNELS inches (3-8 cm) away from the HomeLink buttons. CLEARED”...
Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 5. Press and hold the just trained HomeLink button and 6. At the garage door opener receiver (motor-head unit) observe the EVIC display. If the EVIC display shows in the garage, locate the learn or smart button. This “CHANNEL X TRANSMIT”...
Page 150: Canadian Programming/Gate Programming
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To program the remaining two HomeLink but- 3. Continue to press and hold the HomeLink button tons, begin with Programming step two. Do not repeat while you press and release every two seconds ( cycle ) step one.
Page 151: Erasing Homelink Buttons
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Erasing HomeLink Buttons 2. The EVIC display will show “CHANNEL X TRANS- To erase programming from the three buttons (individual MIT” (where X is Channel 1, 2, or 3) for 20 seconds and buttons cannot be erased but can be reprogrammed - then change to “CHANNEL X TRAINING.”...
Page 152: Power Sunroof - If Equipped
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • This device must accept any interference that may be received including interference that may cause undes- ired operation. NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment.
Page 153: Opening Sunroof - Express
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Opening Sunroof - Express WARNING! Press the switch rearward and release, and the sunroof • Never leave children in a vehicle, with the keys in will open automatically from any position. The sunroof will open fully, then stop automatically.
Page 154: Pinch Protect Override
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE sunroof will automatically retract. Remove the obstruc- Sunshade Operation tion if this occurs. Next, press the switch forward and The sunshade can be opened manually. However, the release to Express Close. sunshade will open automatically as the sunroof opens. Pinch Protect Override NOTE: The sunshade cannot be closed if the sunroof is If a known obstruction (ice, debris, etc.) prevents closing,...
Page 155: Sunroof Maintenance
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Sunroof Maintenance POWER OUTLET Use only a non-abrasive cleaner and a soft cloth to clean To the right of the convenience tray (lower center of the glass panel. instrument panel) is an outlet for electrically powered accessories.
Page 156 156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The rear power outlet (if equipped) is located in the left The power outlets are a direct feed from the battery so rear cargo area. they receive power whether the ignition is in the ON or OFF position.
Page 157: Cup Holders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 CUP HOLDERS CAUTION! In the center console there are two cup holders for the front seat passengers. Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 158: Cargo Area Features
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: The cup holder insert is removable, from the CARGO AREA FEATURES console, for cleaning. It can be reinstalled with the larger Cargo Light cup depression towards the passenger seat, but the top The cargo area light is activated by opening the liftgate, surface will not be flush with the console surface.
Page 159: Rear Storage Compartment
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 Rear Storage Compartment Retractable Cargo Area Cover The rear storage compartment is located on the driver’s NOTE: The purpose of this cover is for privacy, not to side behind the second row seat. secure loads.
Page 160 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. The liftgate may be opened with the cargo cover in WARNING! place. In an accident a cargo cover loose in the vehicle could cause injury. It could fly around in a sudden stop and strike someone in the vehicle.
Page 161: Cargo Tie-Down Hooks
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Cargo Tie-Down Hooks WARNING! The tie-downs located on cargo area floor should be used to safely secure loads when vehicle is moving. Cargo tie-down hooks are not safe anchors for a child seat tether strap. In a sudden stop or collision a hook could pull loose and allow the child seat to come loose.
Page 162 162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Do not carry loads which exceed the load limits WARNING! described on the label attached to the left door or left door center pillar. To help protect against personal injury, passengers should not be seated in the rear cargo area. The rear •...
Page 163: Cargo Load Floor
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 Cargo Load Floor The cargo load floor is held by spring loaded latches. In order to use the cargo load floor, use the following The panel in the load floor is reversible for added utility. procedure: One side is carpeted and the other side features a plastic lined tray which holds a variety of items.
Page 164: Rear Window Features
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Wiper/Washer — If Equipped A switch on the right side of the steering column controls operation of the rear wiper/washer function. Rotating the switch up to the DEL (Delay) position or the ON position will activate the wiper.
Page 165: Rear Window Defroster - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 If the liftgate flipper glass is open, connection to the rear Rear Window Defroster — If Equipped window wiper is interrupted preventing activation of the Press this button (located on the Climate Control rear wiper blade.
Page 167 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel And Controls ... . . 170 Two Types Of Signals ....194 Instrument Cluster .
Page 168 168 UNDERSTANDING YOUR INSTRUMENT PANEL Operation Instructions - Video Entertainment System (Sales Code XRV) — (CD Mode For CD Audio Play) ... 201 If Equipped ......214 Load/Eject Button Satellite Radio —...
Page 169 UNDERSTANDING YOUR INSTRUMENT PANEL 169 Reception Quality ..... 219 Radio Operation And Cellular Phones ..221 Remote Sound System Controls .
Page 170: Instrument Panel And Controls
170 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL AND CONTROLS...
Page 171: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 171 INSTRUMENT CLUSTER...
Page 172: Instrument Cluster Description
172 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 3. Turn Signal Indicator Light The arrow will flash with the exterior turn signal 1. Speedometer when the turn signal lever is operated. Indicates vehicle speed. If the vehicle electronics sense that the vehicle has 2.
Page 173 UNDERSTANDING YOUR INSTRUMENT PANEL 173 engine start. If the bulb does not come on when turning during starting, stays on, or turns on while driving, have the key from OFF to ON, have the condition checked the system inspected by an authorized dealer as soon as promptly.
Page 174 174 UNDERSTANDING YOUR INSTRUMENT PANEL 8. Tachometer Do not operate the vehicle until the cause is corrected. The red segments indicate the maximum permissible This light does not show how much oil is in the engine. engine revolutions-per-minute (r.p.m. x 1000) for each The engine oil level must be checked under the hood.
Page 175 UNDERSTANDING YOUR INSTRUMENT PANEL 175 12. Tire Pressure Monitoring Telltale Light can lead to tire failure. Under-inflation also reduces fuel Each tire, including the spare (if provided), efficiency and tire tread life, and may affect the vehicle’s should be checked monthly when cold and handling and stopping ability.
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Vehicle Information Center Display CAUTION! When the appropriate conditions exist, this display shows the Electronic Vehicle Information Center (EVIC) Driving with a hot engine cooling system could messages. Refer to “Electronic Vehicle Information Cen- damage your vehicle.
Page 177 UNDERSTANDING YOUR INSTRUMENT PANEL 177 16. Seat Belt Reminder Light U.S. federal regulations require that upon transfer of When the ignition switch is first turned ON, this vehicle ownership, the seller certify to the purchaser the light will turn on for 5 to 8 seconds as a bulb check. correct mileage that the vehicle has been driven.
Page 178 178 UNDERSTANDING YOUR INSTRUMENT PANEL 21. Electronic Throttle Control (ETC) Warning Light 22. Front Fog Light Indicator Light— If Equipped This light informs you of a problem with the This light shows the front fog lights are ON. Electronic Throttle Control system. If a problem is detected the light will come on while the 23.
Page 179: Electronic Vehicle Information Center
UNDERSTANDING YOUR INSTRUMENT PANEL 179 • PERFORM SERVICE ELECTRONIC VEHICLE INFORMATION CENTER • KEY NOT PROGRAMMED — DAMAGED KEY • KEY NOT PROGRAMMED — INVALID KEY • KEY NOT PROGRAMMED — EXCEEDED KEY PRO- GRAM LIMIT • PROGRAMMING ACTIVE — NEW KEY PRO- GRAMMED •...
Page 180 180 UNDERSTANDING YOUR INSTRUMENT PANEL • LIFTGATE/DOORS OPEN (with graphic) • WASHER FLUID LOW (with graphic) • LIFTGLASS OPEN (with graphic) • UPSHIFT (with graphic) • HOOD OPEN (with graphic) • CHECK GAUGES • HOOD/DOOR OPEN (with graphic) • AUTO HIGHBEAM ON •...
Page 181: Customer Programmable Features
UNDERSTANDING YOUR INSTRUMENT PANEL 181 • MEMORY #2 POSITIONS SET • LEFT REAR LOW PRESSURE • MEMORY SYSTEM DISABLED — SEATBELT FAS- • RIGHT REAR LOW PRESSURE TENED (with graphic) Customer Programmable Features • MEMORY SYSTEM DISABLED — VEHICLE NOT IN Press the MENU button until one of the display choices PARK following appears:...
Page 182 182 UNDERSTANDING YOUR INSTRUMENT PANEL Language? Display U.S. or Metric? When in this display you may select one of three lan- Pressing the STEP button when in this display selects US guages for all display nomenclature, including the trip or Metric. The overhead console and instrument panel computer functions.
Page 183 UNDERSTANDING YOUR INSTRUMENT PANEL 183 Remote Unlock Driver’s Door 1st? memory set position using the door mounted switch. When this feature is selected only the driver’s door will Pressing the STEP button when in this display will select unlock on the first press of the remote keyless entry “Yes”...
Page 184 184 UNDERSTANDING YOUR INSTRUMENT PANEL Headlamp Delay this display will select “Low Beam” or “Low/High When this feature is selected the driver can choose, when Beam.” Refer to “Lights — SmartBeams” in Section 3 of exiting the vehicle, to have the headlamps remain on for this manual.
Page 185 UNDERSTANDING YOUR INSTRUMENT PANEL 185 Front Wipers Rain Sense? (Available with Rain Easy Entry/Exit Seat? (Available with Memory Seat Sensing Wipers Only) Only) Pressing the STEP button when in this display will select This feature provides automatic driver’s seat positioning “Manual”...
Page 186: Compass/Temperature/Trip Computer
186 UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature/Trip Computer This display provides the outside temperature, one of the eight compass headings to indicate the direction the vehicle is facing, and vehicle trip information. The com- pass and temperature display is the normal display. When the C/T button is pressed the compass/ temperature display returns.
Page 187 UNDERSTANDING YOUR INSTRUMENT PANEL 187 WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
Page 188: Trip Computer
188 UNDERSTANDING YOUR INSTRUMENT PANEL Trip Computer This feature, located in the instrument cluster, displays the following information when the display is in the “Compass/Temperature” mode and the STEP button is pressed: Step Button Press the STEP button to cycle through all of the Compass/Mini-Trip Computer displays.
Page 189 UNDERSTANDING YOUR INSTRUMENT PANEL 189 Reset Button Average Fuel Economy Press the RESET button to reset the display you are in. Shows the average fuel economy since the last reset. Press and hold the RESET button (for 2 seconds) to reset When the fuel economy is reset, the display will read all of the displays.
Page 190 190 UNDERSTANDING YOUR INSTRUMENT PANEL Elapsed Time Shows the accumulated ignition ON time since the last reset. Engine Oil Pressure Shows the current engine oil pressure. The scale will read from 0–100 psi (0–689 kPa). Engine Oil Temperature Shows the current engine oil temperature. The scale will read from 140°...
Page 191 UNDERSTANDING YOUR INSTRUMENT PANEL 191 NOTE: Tires heat up during normal driving conditions. Manual Compass Calibration Heat will cause the tire pressure to increase from 2 to 6 If the compass appears erratic and the “CAL” symbol psi (14 to 41 kPa) during normal driving conditions. Refer does not appear, you must manually put the compass to “Tire Inflation Pressures”...
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL To Put Into a Calibration Mode Start the engine, and leave the transmission in the P (Park) position. display “Compass/ Temperature.” Press and hold the C/T button for ap- proximately 5 seconds to change the display to compass variance mode;...
Page 193 UNDERSTANDING YOUR INSTRUMENT PANEL 193 Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
Page 194: Radio General Information
194 UNDERSTANDING YOUR INSTRUMENT PANEL To set the variance: Turn the ignition ON and set the Two Types of Signals display to “Compass/Temperature.” Press the C/T but- There are two basic types of radio signals... AM or ton approximately 5 seconds. The last variance zone Amplitude Modulation, in which the transmitted sound number will be displayed.
Page 195: Fm Reception
UNDERSTANDING YOUR INSTRUMENT PANEL 195 FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: The radio, steering wheel radio controls (if equipped), and 6 disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition...
Page 196 196 UNDERSTANDING YOUR INSTRUMENT PANEL Power Switch/Volume Control (Rotary) SEEK Button (Radio Mode) Press the ON/VOL control to turn the radio ON. Press Press and release the SEEK button to search for the next the ON/VOL a second time to turn OFF the radio. listenable station in either AM/FM or Satellite (if equipped) mode.
Page 197 UNDERSTANDING YOUR INSTRUMENT PANEL 197 SCAN Button (Radio Mode) 2. Adjust the hours by turning the right side Tune / Pressing the SCAN button causes the tuner to search for Audio control. the next listenable station, in either AM, FM or Satellite (if 3.
Page 198 198 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Button (Radio Mode) Press the rotary TUNE control a fifth time and FADE will Press the button to select AM or FM Modes. display. Turn the TUNE control to the left or right to adjust the sound level between the front and rear speak- Setting the Tone, Balance, and Fade ers.
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 199 Toggle the PTY button to select the following format Nostalgia Nostalgia types: Oldies Oldies 16 Digit-Character Dis- Personality Personality Program Type play Public Public No program type or un- None Rhythm and Blues Rhythm_and_Blues defined Religious Music Religious_Music Adult Hits...
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is You may add a second station to each push-button by displayed, the radio will be tuned to the next frequency repeating the above procedure with this exception: Press station with the same selected PTY name.
Page 201: Understanding Your Instrument Panel 201
UNDERSTANDING YOUR INSTRUMENT PANEL 201 Operation Instructions - (CD MODE for CD Audio CAUTION! Play) This CD player will accept 4 3/4 inch (12 cm) discs NOTE: The ignition switch must be in the ON or ACC only. The use of other sized discs may damage the position to operate the radio.
Page 202: Load/Eject Button (Cd Mode For Cd Audio Play)
202 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Button (CD MODE for CD Audio Play) LOAD/EJECT Button (CD Mode for CD Audio Press the right side of the SEEK button for the next Play) selection on the CD. Press the left side of the button to LOAD/ EJECT - Load return to the beginning of the current selection, or return Press the LOAD/ EJECT button and the push-...
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 203 Radio display will show EJECTING DISC when the disc TIME Button (CD MODE for CD Audio Play) is being ejected and prompt the user to remove the disc. Press this button to change the display from a large CD playing time display to a small CD playing time display.
Page 204: Notes On Playing Mp3 Files
204 UNDERSTANDING YOUR INSTRUMENT PANEL RND/PTY Button (Random Play Button) (CD Notes On Playing MP3 Files MODE for CD Audio Play) The radio can play MP3 files, however, acceptable MP3 Press this button while the CD is playing to activate file recording media and formats are limited.
Page 205 UNDERSTANDING YOUR INSTRUMENT PANEL 205 • Maximum number of files: 255 Supported MP3 File Formats The radio will recognize only files with the *.mp3 exten- • Maximum number of folders: 100 sion as MP3 files. Non-MP3 files named with the *.mp3 •...
Page 206 206 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3 Files MPEG Specifi- Sampling Fre- Bit rate (kbps) When a medium containing MP3 data is loaded, the cation quency (kHz) radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
Page 207: Operation Instructions
UNDERSTANDING YOUR INSTRUMENT PANEL 207 Operation Instructions - (CD Mode for MP3 Audio LOAD / EJECT - Eject Play) Press the LOAD/ EJECT button and the push- button with the corresponding number where SEEK Button (CD Mode for MP3 Play) the CD was loaded and the disc will unload Pressing the right side of the SEEK button plays the next and move to the entrance for easy removal.
Page 208 208 UNDERSTANDING YOUR INSTRUMENT PANEL MSG or INFO Button (CD Mode for MP3 Play) AM/FM Button (CD Mode for MP3 Play) Press and MSG or INFO button while playing MP3 disc. Switches back to Radio mode. The radio scrolls through the following TAG information: RND/ PTY Button (CD Mode for MP3 Play) Song Title, Artist, File Name, and Folder Name (if avail- Pressing this button plays files randomly.
Page 209: Sales Code Rec - Am/Fm/Cd (6-Disc) Radio With Navigation System
UNDERSTANDING YOUR INSTRUMENT PANEL 209 Operating Instructions - Hands Free Phone (If SALES CODE REC — AM/FM/CD (6–DISC) RADIO Equipped) WITH NAVIGATION SYSTEM Refer to Hands Free Phone in Section 3 of the Owner’s Manual. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual.
Page 210: Operating Instructions - Satellite Radio (If Equipped)
210 UNDERSTANDING YOUR INSTRUMENT PANEL Satellite Navigation Radio with CD Player with MP3 Operating Instructions — Satellite Radio (If Capability (REC) - combines a Global-Positioning Equipped) System-based navigation system with an integrated color Refer to your “Navigation User’s Manual” for detailed screen to provide maps, turn identification, selection operating instructions.
Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 211 1. At the Main Menu screen, highlight “Clock Setup” 2. To show the GPS clock, select “Displayed Clock: GPS and press ENTER OR press and hold for 3 seconds the Clock” and press ENTER. TIME button on the unit’s faceplate. The Clock Setup 3.
Page 212 212 UNDERSTANDING YOUR INSTRUMENT PANEL 1. At the Clock Setup screen highlight “Displayed 3. To decrease the clock by one hour, use the Select Clock: User Defined Clock”. Encoder to highlight the “-” sign. Press ENTER. Press ENTER again to decrease the clock by another hour. 4.
Page 213: Audio Clock Display
UNDERSTANDING YOUR INSTRUMENT PANEL 213 Audio Clock Display 3. To switch the clock to the small clock, quickly press TIME again. Select this option to change the size of the clock on the audio screens. 1. When you are at an audio screen, quickly press the TIME button on the navigation faceplate.
Page 214: Video Entertainment System (Sales Code Xrv) - If Equipped
214 UNDERSTANDING YOUR INSTRUMENT PANEL VIDEO ENTERTAINMENT SYSTEM (SALES CODE XRV) — IF EQUIPPED The optional VES™ (Video Entertainment System) con- sists of a DVD player and LCD (liquid crystal display) screen, a battery-powered remote control, and two head- sets. The DVD player is mounted in the rear of the center console storage bin, and is concealed by a door that lifts up for access.
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 215 The LCD screen is located on the headliner behind the front seats. Remote Control Location Lowering the DVD Screen...
Page 216: Satellite Radio - If Equipped
216 UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO — IF EQUIPPED Electronic Serial Number/Sirius Identification Satellite radio uses direct satellite to receiver broadcast- Number (ESN/SID) ing technology to provide clear digital sound, coast to The Electronic Serial Number/Sirius Identification Num- coast. The subscription service provider is Sirius™ Satel- ber is needed to activate your Sirius Satellite Radio lite Radio.
Page 217: Selecting Satellite Mode In Raq Radios
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Selecting Satellite Mode in RAQ Radios Selecting a Channel Press the MODE button repeatedly until the word Press and release the SEEK or TUNE buttons to search for SIRIUS appears in the display. These radios will also the next channel.
Page 218: Storing And Selecting Pre-Set Channels
218 UNDERSTANDING YOUR INSTRUMENT PANEL Storing and Selecting Pre-Set Channels one and stop the search. Pressing a pre-set memory In addition to the 10 AM and 10 FM pre-set stations, you button during a music type scan, will call up the memory may also commit 10 satellite stations to push button channel and stop the search.
Page 219: Reception Quality
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Reception Quality Satellite reception may be interrupted due to one of the following reasons. • The vehicle is parked in an underground parking structure or under a physical obstacle. • Dense tree coverage may interrupt reception. •...
Page 220: Radio Operation
220 UNDERSTANDING YOUR INSTRUMENT PANEL Pressing the center button will make the radio switch CD Player between the various modes available (AM/FM/TAPE/ Pressing the top of the switch once will go to the next CD, Etc.). track on the CD. Pressing the bottom of the switch once will go to the beginning of the current track or to the The left hand control is a rocker type switch with a beginning of the previous track if it is within one second...
Page 221: Cd/Dvd Disc Maintenance
UNDERSTANDING YOUR INSTRUMENT PANEL 221 CD/DVD DISC MAINTENANCE RADIO OPERATION AND CELLULAR PHONES To keep the CD/DVD discs in good condition, take the Under certain conditions, the cellular phone being On in following precautions: your vehicle can cause erratic or noisy performance from your radio.
Page 222: Climate Controls
222 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Automatic Temperature Control The Infrared Dual-Zone Climate Control System auto- matically maintains the interior comfort level desired by the driver and passenger. This is accomplished by a dual sun-sensor in the top of the instrument panel, and an infrared sensor located in the face of the control unit.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 223 LO AUTO position should be used for front seat occu- temperature out of the ducts will be full hot or full cold pants only. The HI AUTO position should be used when respectively. With the temperature setting in these posi- more air flow is desired, or when rear seat occupants are tions, the system does not attempt automatic comfort present.
Page 224 224 UNDERSTANDING YOUR INSTRUMENT PANEL debris due to the climate control sensor’s location. present and the Recirc button is pressed the indicator Mud on the windshield may also cause poor operation will flash and remain off. This tells you that you are of this system.
Page 225 UNDERSTANDING YOUR INSTRUMENT PANEL 225...
Page 226 226 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Regardless of the type of operation, when a NOTE: The defrost mode is not automatically selected. temperature knob is set to the full clockwise or full It must be manually selected, when desired. counterclockwise position, the system will deliver full •...
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 227 Air flows through the registers in the back of the This button can be used to block out smoke, center console, and under the front seats to the rear odors, dust, high humidity, or if rapid cooling seat passengers.
Page 228: Operating Tips
228 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips smoke, perfumes, etc.) from sticking to the windows. Contaminates increase the rate of window fogging. Window Fogging Windows will fog on the inside when the humidity inside Summer Operation the vehicle is high. This often occurs in mild or cool Air conditioned vehicles must be protected with a high temperatures when it’s rainy or humid.
Page 229 UNDERSTANDING YOUR INSTRUMENT PANEL 229 Your air conditioning system is also equipped with an Vacation Storage automatic recirculation system. When the system senses Anytime you store your vehicle, or keep it out of service a heavy load or high heat conditions, it may use partial (i.e.
Page 231: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ..... 234 Rocking The Vehicle ....241 Normal Starting .
Page 232 232 STARTING AND OPERATING Tire Identification Number (TIN) ..253 Tire Rotation Recommendations ... . 266 Tire Loading And Tire Pressure ... 254 Tire Pressure Monitor System (TPMS) .
Page 233 STARTING AND OPERATING 233 Trailer Towing ......277 Trailer And Tongue Weight ....282 Common Towing Definitions .
Page 234: Starting Procedures
234 STARTING AND OPERATING STARTING PROCEDURES Start the engine with the gear selector in the N (Neutral) Before starting your vehicle, adjust your seat, adjust both or P (Park) position. Apply the brakes before shifting to inside and outside mirrors, and fasten your seat belts. any driving gear.
Page 235: Extreme Cold Weather (Below -20°F (-29°C)
STARTING AND OPERATING 235 If Engine Fails to Start If the engine fails to start after you have followed the “Normal Starting” or “Extreme Cold Weather” proce- dures, it may be flooded. Push the accelerator pedal all the way to the floor and hold it there while cranking the engine.
Page 236 236 STARTING AND OPERATING WARNING! WARNING! Never pour fuel or other flammable liquids into the Do not attempt to push or tow your vehicle to get it throttle body air inlet opening in an attempt to start started. Vehicles equipped with an automatic trans- the vehicle.
Page 237: After Starting
STARTING AND OPERATING 237 released. If this occurs, continue cranking with the accel- CAUTION! erator pedal pushed all the way to the floor. Release the accelerator pedal and the key once the engine is running Long periods of engine idling, especially at high smoothly.
Page 238: Automatic Transmission
238 STARTING AND OPERATING AUTOMATIC TRANSMISSION WARNING! It is dangerous to shift the selector lever out of P CAUTION! (Park) or N (Neutral) if the engine speed is higher than idle speed. If your foot is not firmly on the Damage to the transmission may occur if the follow- brake pedal, the vehicle could accelerate quickly ing precautions are not observed:...
Page 239: 5-Speed Automatic Transmission
STARTING AND OPERATING 239 5–Speed Automatic Transmission WARNING! The electronically controlled transmission provides a precise shift schedule. The transmission electronics are It is dangerous to shift the selector lever out of P self-calibrating; therefore, the first few shifts on a new (Park) or N (Neutral) if the engine speed is higher vehicle, may be somewhat abrupt.
Page 240 240 STARTING AND OPERATING P (Park) R (Reverse) Supplements the parking brake by locking the transmis- Shift into this range only after the vehicle has come to a sion. The engine can be started in this range. Never use P complete stop.
Page 241: Rocking The Vehicle
STARTING AND OPERATING 241 Rocking the Vehicle five rocking-motion cycles. This will minimize overheat- If the vehicle becomes stuck in snow, sand, or mud, it can ing and reduce the risk of transmission failure during often be moved by a rocking motion. Move the gear prolonged efforts to free a stuck vehicle.
Page 242: Autostick Operation
242 STARTING AND OPERATING can also provide the driver with more control during 2nd gear and a Boxed 2 will be displayed in the PRNDL. passing, city driving, mountain driving, trailer towing, Once Autostick mode is engaged a move to the Right (+) and many other situations.
Page 243: Autostick General Information
STARTING AND OPERATING 243 (EVIC) portion of your instrument cluster. This message Autostick General Information appears in order to alert the driver that the engine speed • You can start out in first or second gear. The system is approaching it’s maximum value and a upshift to the will ignore attempts to upshift at too low of a vehicle next gear is required.
Page 244: Parking Brake
244 STARTING AND OPERATING PARKING BRAKE To set the parking brake, pull the lever up as firmly as possible. When the parking brake is applied with the ignition ON, the “Brake Warning Light” in the instru- ment cluster will light. To release the parking brake, pull up slightly, press the center button, then lower the lever completely.
Page 245: Anti-Lock Brake System
STARTING AND OPERATING 245 When parking on a hill, turn the front wheels toward the WARNING! curb on a downhill grade and away from the curb on an • Always fully apply the parking brake when leav- uphill grade. ing your vehicle, or it may roll and cause damage The parking brake should always be applied whenever or injury.
Page 246 246 STARTING AND OPERATING WARNING! WARNING! Significant over or under inflation of tires can lead Pumping of the Anti-Lock Brakes will diminish to loss of braking effectiveness. their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to The Anti-Lock Brake System conducts a low-speed self- slow down or stop.
Page 247 STARTING AND OPERATING 247 WARNING! CAUTION! • The Anti-Lock Brake System (ABS) cannot pre- The Anti-Lock Brake System is subject to possible vent the natural laws of physics from acting on the detrimental effects of electronic interference caused vehicle, nor can it increase braking or steering by improperly installed after-market radios or tele- efficiency beyond that afforded by the condition phones.
Page 248: Power Steering
248 STARTING AND OPERATING • Do not “ride” the brakes by resting your foot on the build up between the tire tread and the road. This pedal. This could overheat the brakes and result in hydroplaning action can cause loss of traction, braking unpredictable braking action, longer stopping dis- ability, and control.
Page 249 STARTING AND OPERATING 249 NOTE: Increased noise levels at the end of the steering CAUTION! wheel travel are considered normal and do not indicate that there is a problem with the power steering system. Prolonged operation of the steering system at the end of the steering wheel travel will increase the Upon initial start-up in cold weather, the power steering steering fluid temperature and it should be avoided...
Page 250: Tire Safety Information
250 STARTING AND OPERATING • European Metric tire sizing is based on European TIRE SAFETY INFORMATION design standards. Tires designed to this standard have Tire Markings the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 251 STARTING AND OPERATING 251 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 252 252 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 253: Tire Identification Number (Tin)
STARTING AND OPERATING 253 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall tires as mounted on the vehicle. If the TIN is not found on The TIN may be found on one or both sides of the tire; the outboard side then you will find it on the inboard side however, the date code may only be on one side.
Page 254: Tire Loading And Tire Pressure
254 STARTING AND OPERATING Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle...
Page 255 STARTING AND OPERATING 255 Loading combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
Page 256 256 STARTING AND OPERATING passengers in your vehicle, the amount of available cargo NOTE: The following table shows examples on how to and luggage load capacity is 650 lbs. (since 5 x 150 = 750, calculate total load, cargo/luggage, and towing capaci- and 1400 –...
Page 257 STARTING AND OPERATING 257...
Page 258: Tires - General Information
258 STARTING AND OPERATING WARNING! WARNING! Overloading of your tires is dangerous. Overloading Do not exceed 50 mph (80 km/h) if the “Tire Pressure can cause tire failure, affect vehicle handling, and Monitoring Telltale Light” is illuminated. Vehicle increase your stopping distance. Use tires of the handling and braking may be reduced.
Page 259 STARTING AND OPERATING 259 1. Safety— 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal WARNING! wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under inflation also increases Improperly inflated tires are dangerous and can cause accidents.
Page 260: Tire Inflation Pressures
260 STARTING AND OPERATING Tire Inflation Pressures check tire pressure. Do not make a visual judgement The proper cold tire inflation pressure is listed on either when determining proper inflation. Radial tires may look the face of the driver’s door, or the driver’s side “B” pillar. properly inflated even when they are under inflated.
Page 261: Tire Pressures For High Speed Operation
STARTING AND OPERATING 261 Check tire pressures more often if subject to a wide range Tire Pressures for High Speed Operation of outdoor temperatures, as tire pressures vary with The manufacturer advocates driving at safe speeds temperature changes. within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Tire pressures change by approximately 1 psi (7 kPa) per speeds, maintaining correct tire inflation pressure is very...
Page 262: Radial-Ply Tires
262 STARTING AND OPERATING Radial-Ply Tires WARNING! High speed driving with your vehicle under maxi- WARNING! mum load is dangerous. The added strain on your tires could cause them to fail. You could have a Combining radial ply tires with other types of tires serious accident.
Page 263: Tire Spinning
STARTING AND OPERATING 263 Tire Spinning Tread Wear Indicators When stuck in mud, sand, snow, or ice conditions, do not Tread wear indicators are in the original equipment tires spin your vehicle’s wheels above 35 mph (55 km/h). to help you in determining when your tires should be replaced.
Page 264: Life Of Tire
264 STARTING AND OPERATING becomes 1/16 inch (2 mm). When the indicators appear WARNING! in 2 or more adjacent grooves, the tire should be replaced. All tires should be replaced after six years, regard- Many states have laws requiring tire replacement at this less of the remaining tread.
Page 265: Replacement Tires
STARTING AND OPERATING 265 Replacement Tires WARNING! The tires on your new vehicle provide a balance of many • characteristics. They should be inspected regularly for Do not use a tire, wheel size or rating other than that wear and correct cold tire inflation pressure. The manu- specified for your vehicle.
Page 266: Alignment And Balance
266 STARTING AND OPERATING Improper alignment will not cause vehicle vibration. CAUTION! Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and Replacing original tires with tires of a different size avoid tire cupping and spotty wear. may result in false speedometer and odometer read- ings.
Page 267 STARTING AND OPERATING 267 • Tire Pressure Monitoring System Display Messages in NOTE: It is particularly important, for you to check the tire pressure in all of your tires regularly and to maintain the EVIC the proper pressure. • Tire Pressure Monitoring Telltale Light The “Tire Pressure Monitoring Telltale Light”...
Page 268 268 STARTING AND OPERATING The following warnings will cause a text message to be LEFT FRONT, LEFT REAR, RIGHT FRONT, displayed, an audible chime to sound, and the “Tire RIGHT REAR LOW PRESSURE Pressure Monitoring Telltale Light” to illuminate. The One or more of these messages will be displayed in the audible chime will occur once every ignition cycle for EVIC if a low tire pressure condition exists in one or more...
Page 269 STARTING AND OPERATING 269 CAUTION! CAUTION! The TPMS has been optimized for the original After inspecting or adjusting the tire pressure al- equipment tires and wheels. TPMS pressures have ways reinstall the valve stem cap. This will prevent been established for the tire size equipped on your moisture and dirt from entering the valve stem, vehicle.
Page 270: General Information
270 STARTING AND OPERATING General Information FUEL REQUIREMENTS This device complies with part 15 of the FCC rules and Your vehicle is designed to meet all emis- RSS 210 of Industry Canada. Operation is subject to the sion regulations and provide excellent fuel following conditions: economy when using high quality pre- mium unleaded gasoline having an octane...
Page 271: Reformulated Gasoline
STARTING AND OPERATING 271 Over 40 automobile manufacturers around the world Gasoline/Oxygenate Blends have issued and endorsed consistent gasoline specifica- Some fuel suppliers blend unleaded gasoline with oxy- tions (the World Wide Fuel Charter, WWFC) to define genates such as 10% ethanol, MTBE, and ETBE. Oxygen- fuel properties necessary to deliver enhanced emissions, ates are required in some areas of the country during the engine performance, and durability for your vehicle.
Page 272: Mmt In Gasoline
272 STARTING AND OPERATING manufacturer. While MTBE is an oxygenate made from It is even more important to look for gasolines without Methanol, it does not have the negative effects of Metha- MMT in Canada, because MMT can be used at levels nol.
Page 273: Fuel System Cautions
STARTING AND OPERATING 273 Fuel System Cautions products contain high concentrations of methanol. Fuel system damage or vehicle performance problems resulting from the use of such fuels or additives are not CAUTION! the responsibility of the manufacturer. Follow these guidelines to maintain your vehicle’s NOTE: Intentional tampering with emissions control performance: systems can result in civil penalties being assessed...
Page 274: Adding Fuel
274 STARTING AND OPERATING garage, and never sit in a parked vehicle with the ADDING FUEL engine running for an extended period. If the vehicle is Fuel Filler Cap (Gas Cap) stopped in an open area with the engine running for The gas cap is located behind the fuel filler door, on the more than a short period, adjust the ventilation system driver’s side of the vehicle.
Page 275 STARTING AND OPERATING 275 CAUTION! CAUTION! Damage to the fuel system or emission control To avoid fuel spillage and overfilling, do not “top system could result from using an improper fuel cap off” the fuel tank after filling. (gas cap). A poorly fitting cap could let impurities into the fuel system.
Page 276 276 STARTING AND OPERATING NOTE: Tighten the gas cap about 1/4 turn until you EVIC (Electronic Vehicle Information Center). Refer to hear one click. This is an indication that cap is properly “Electronic Vehicle Information Center” in Section 4 of tightened.
Page 277: Trailer Towing
STARTING AND OPERATING 277 Common Towing Definitions WARNING! The following trailer towing related definitions will assist • Never add fuel when the engine is running. you in understanding the following information: • Never have any smoking materials lit in or near Gross Vehicle Weight Rating (GVWR) the vehicle when the fuel cap is removed or the The GVWR is the total allowable weight of your vehicle.
Page 278 278 STARTING AND OPERATING Gross Combination Weight Rating (GCWR) Tongue Weight (TW) The gross combination weight rating (GCWR) is the total The downward force exerted on the hitch ball by the permissible weight of your vehicle and trailer when trailer. In most cases it should not be less than 10% or weighed in combination.
Page 279 STARTING AND OPERATING 279 hitches are the most popular on the market today and WARNING! they’re commonly used to tow small- and medium-sized trailers. An improperly adjusted Weight Distributing Hitch system may reduce handling, stability, braking per- Weight-Distributing Hitch formance, and could result in an accident. A weight-distributing system works by applying lever- Weight Distributing Systems may not be compatible age through spring (load) bars.
Page 280 280 STARTING AND OPERATING Weight Distributing Hitch System Improper Adjustment of Weight Distributing System...
Page 281: Trailer Hitch Classification
STARTING AND OPERATING 281 Trailer Hitch Classification Trailer Hitch Classification Your vehicle may be factory equipped for safe towing of Class Max. GTW (Gross Trailer trailers weighing over 3,500 lbs (1 587 kg) with the Wt.) optional Trailer Tow Prep Package. See your dealer for Class I - Light Duty 2,000 lbs (907 kg) package content.
Page 282: Trailer Towing Weights (Maximum Trailer Weight Ratings)
282 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/ GCWR (Gross Combined Frontal Area Max. GTW (Gross Max. Tongue Wt. Transmission Wt. Rating) Trailer Wt.) (See Note 1) 6.1L Automatic...
Page 283 STARTING AND OPERATING 283 • The weight of any other type of cargo or equipment Never exceed the maximum tongue weight stamped on your trailer hitch. put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle.
Page 284: Towing Requirements
284 STARTING AND OPERATING Towing Requirements WARNING! To promote proper break-in of your new vehicle driv- etrain components the following guidelines are recom- Improper towing can lead to an injury accident. mended: Follow these guidelines to make your trailer towing as safe as possible: Make certain that the load is secured in the trailer CAUTION!
Page 285 STARTING AND OPERATING 285 • Safety chains must always be used between your 4. Tongue weight rating for the trailer hitch utilized vehicle and trailer. Always connect the chains to the (This requirement may limit the ability to always hook retainers of the vehicle hitch. Cross the chains achieve the 10% to 15% range of tongue weight as a under the trailer tongue and allow enough slack for percentage of total trailer weight).
Page 286 286 STARTING AND OPERATING − When replacing tires, refer to “Tires–General Informa- − Trailer brakes are recommended for trailers over 1,000 tion” for proper tire replacement procedures. Replac- lbs (454 kg) and required for trailers in excess of 2,000 ing tires with a higher load carrying capacity will not lbs (907 kg).
Page 287 STARTING AND OPERATING 287 The electrical connections are all complete to the vehicle WARNING! but you must mate the harness to a trailer connector. Refer to the following illustrations. Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- tem and cause it to fail.
Page 288: Towing Tips
288 STARTING AND OPERATING Towing Tips — Automatic Transmission The “D” range can be selected when towing. However, if frequent shifting occurs while in this range, the “3” range should be selected. NOTE: Using the “3” range while operating the vehicle under heavy operating conditions will improve perfor- mance and extend transmission life by reducing exces- sive shifting and heat build up.
Page 289: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 289 Towing Tips — Electronic Speed Control (If − Air Conditioning Equipped) Turn off temporarily. − Don’t use in hilly terrain or with heavy loads. − refer to Cooling System Operating information in the Maintenance section of this manual for more informa- −...
Page 291: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flashers ....292 Jump Starting ......293 If Your Engine Overheats .
Page 292 292 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS Your vehicle’s hazard warning flasher is an emergency warning system. When you activate it, all front and rear directional signals will flash intermittently. Use it when your vehicle is disabled on or near the road. It warns other drivers to steer clear of you and your vehicle.
Page 293 WHAT TO DO IN EMERGENCIES 293 IF YOUR ENGINE OVERHEATS CAUTION! In any of the following situations, you can reduce the potential for overheating by taking the appropriate ac- Driving with a hot cooling system could damage tion. your vehicle. If the temperature gauge reads “H”, pull over and stop the vehicle.
Page 294 294 WHAT TO DO IN EMERGENCIES 2. Park the booster vehicle within cable reach but with- WARNING! out letting the vehicles touch. Set the parking brake on both vehicles, place the transmission in P (Park), and turn Battery fluid is a corrosive acid solution; do not the ignition OFF.
Page 295 WHAT TO DO IN EMERGENCIES 295 1. Remove all metal jewelry such as watch bands or WARNING! bracelets which might make an unintended electrical contact. Do not permit vehicles to touch each other as this could establish a ground connection and personal 2.
Page 296 296 WHAT TO DO IN EMERGENCIES WARNING! WARNING! • You should not try to start your vehicle by push- Any procedure other than above could result in: ing or towing. 1. Personal injury caused by electrolyte squirting • Do not connect the cable to the negative post of out the battery vent;...
Page 297 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment – 6.1L ....300 Engine Oil Filter ..... . 308 Onboard Diagnostic System —...
Page 298 298 MAINTAINING YOUR VEHICLE Power Steering Fluid Check ....314 Appearance Care And Protection From Corrosion ......329 Body Lubrication .
Page 299 MAINTAINING YOUR VEHICLE 299 Front Fog Light ..... . 343 Fluids, Lubricants, And Genuine Parts ..347 Rear Tail, Stop, Turn Signal, And Back-Up Engine .
Page 300: Engine Compartment - 6.1L
300 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT – 6.1L...
Page 301: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 301 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 302: Loose Fuel Filler Cap Message
302 MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message outside temperatures. If the test is performed and the After fuel is added, the vehicle diagnostic system can problem is gone, the message will disappear. determine if the fuel filler cap is loose, improperly If the problem persists, the message will appear the next installed, or damaged.
Page 303 MAINTAINING YOUR VEHICLE 303 is functioning and is not on when the engine is running, 4. As soon as you turn your key to the ON position, you and that the OBD (On Board Diagnostic) system is ready will see your MIL symbol come on as part of a normal for testing.
Page 304: Replacement Parts
304 MAINTAINING YOUR VEHICLE you may need to do nothing more than drive your DEALER SERVICE vehicle as you normally would in order for your OBD Your dealer has the qualified service personnel, special system to update. A recheck with the above test routine tools and equipment to perform all service operations in may then indicate that the system is now ready.
Page 305: Maintenance Procedures
MAINTAINING YOUR VEHICLE 305 could adversely affect the engine or vehicle performance. WARNING! These items should be inspected if a malfunction is observed or suspected. You can be badly injured working on or around a motor vehicle. Do only that service work for which Engine Oil you have the knowledge and the proper equipment.
Page 306 306 MAINTAINING YOUR VEHICLE NOTE: Fill engine oil one quart at a time. CAUTION! Overfilling or underfilling will cause oil aeration or loss of oil pressure. This could damage your engine. CAUTION! Operating the engine with the oil levels below the safe zone, or operating with oil levels that exceed the top of the safe zone may cause engine damage.
Page 307 MAINTAINING YOUR VEHICLE 307 • Stop and go driving. NOTE: Under no circumstances should oil change in- tervals exceed 6,000 miles (10 000 km) or 6 months • Extensive engine idling. whichever comes first. • Driving in dusty conditions. Engine Oil Selection •...
Page 308: Engine Oil Filter
308 MAINTAINING YOUR VEHICLE Engine Oil Viscosity Chart Materials Added to Engine Oil The proper SAE viscosity grade of engine oil should be The manufacturer strongly recommends against the ad- selected based on the following recommendation and be dition of any additives (other than leak detection dyes) to within the operating temperature shown in the engine oil the engine oil.
Page 309: Drive Belts - Check Condition And Tensioner
MAINTAINING YOUR VEHICLE 309 Engine Oil Filter Selection Belts should be inspected for evidence of cuts, cracks, The manufacturer’s engines have a full-flow type oil glazing, or frayed cords and replaced if there is indication filter. Use a filter of this type for replacement. The quality of damage which could result in belt failure.
Page 310: Engine Air Cleaner Filter
310 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Fuel Filter Under normal driving conditions, replace the air filter at A plugged fuel filter can cause stalling, limit the speed at the intervals shown on “Maintenance Schedule A.” If, which a vehicle can be driven or cause hard starting. however, you drive the vehicle frequently under dusty or Should an excessive amount of dirt accumulate in the severe conditions, the filter element should be inspected...
Page 311 MAINTAINING YOUR VEHICLE 311 WARNING! CAUTION! A hot exhaust system can start a fire if you park over Damage to the catalytic converter can result if your materials that can burn. Such materials might be vehicle is not kept in proper operating condition. In grass or leaves coming into contact with your ex- the event of engine malfunction, particularly involv- haust system.
Page 312: Maintenance-Free Battery
312 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: WARNING! • Do not shut off the engine or interrupt the ignition Battery posts, terminals, and related accessories con- when the transmission is in gear and the vehicle is in tain lead and lead compounds.
Page 313: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 313 To determine the battery charge, check the battery test Air Conditioner Maintenance indicator (if equipped) on top of the battery. Refer to the For best possible performance, your air conditioner illustration. should be checked and serviced by an Authorized Dealer at the start of each warm season.
Page 314: Power Steering Fluid Check
314 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling WARNING! R-134a Air Conditioning Refrigerant is a hydrofluorocar- • Use only refrigerants and compressor lubricants bon (HFC) that is endorsed by the Environmental Pro- tection Agency and is an ozone-saving product. How- approved by the manufacturer for your air condi- ever, the manufacturer recommends that air conditioning tioning system.
Page 315 MAINTAINING YOUR VEHICLE 315 WARNING! CAUTION! Fluid level should be checked on a level surface with Do not use Automatic Transmission Fluid (ATF) or the engine off to prevent injury from moving parts, other types of power steering fluids when servicing and to insure accurate fluid level reading.
Page 316: Body Lubrication
316 MAINTAINING YOUR VEHICLE Body Lubrication Windshield Wiper Blades Locks and all body pivot points, including such items as The rubber edges of the wiper blades and the windshield seat tracks, doors, trunk and hood hinges, should be should be cleaned periodically with a sponge or soft cloth lubricated periodically to assure quiet, easy operation and a mild nonabrasive cleaner.
Page 317: Exhaust System
MAINTAINING YOUR VEHICLE 317 the “Washer Fluid Low” message will be displayed. Refer Exhaust System to “Electronic Vehicle Information Center” in Section 4 of The best protection against carbon monoxide entry into this manual. the vehicle body is a properly maintained engine exhaust system.
Page 318: Cooling System
318 MAINTAINING YOUR VEHICLE Cooling System WARNING! Exhaust gases can injure or kill. They contain carbon WARNING! monoxide (CO) which is colorless and odorless. • When working near the radiator cooling fan, dis- Breathing it can make you unconscious and can eventually poison you.
Page 319 MAINTAINING YOUR VEHICLE 319 applicable). If coolant is dirty or rusty in appearance, the Cooling System — Drain, Flush and Refill system should be drained, flushed and refilled with fresh At the intervals shown on the appropriate “Maintenance coolant. Check the front of the A/C condenser for any Schedule,”...
Page 320 320 MAINTAINING YOUR VEHICLE Adding Coolant CAUTION! Your vehicle has been built with an improved engine coolant that allows extended maintenance intervals. This Mixing of coolants other than specified HOAT en- coolant can be used up to 5 Years or 100,000 miles before gine coolants, may result in engine damage and may replacement.
Page 321 MAINTAINING YOUR VEHICLE 321 The use of lower quality water will reduce the amount of WARNING! corrosion protection in the engine cooling system. • The warning words “DO NOT OPEN HOT” on Please note that it is the owner’s responsibility to main- the cooling system pressure cap are a safety pre- tain the proper level of protection against freezing ac- caution.
Page 322 322 MAINTAINING YOUR VEHICLE do not store ethylene glycol based engine coolant in open Points To Remember containers or allow it to remain in puddles on the NOTE: When the vehicle is stopped after a few miles (a ground. If ingested by a child, contact a physician few kilometers) of operation, you may observe vapor immediately.
Page 323: Hoses And Vacuum/Vapor Harnesses
MAINTAINING YOUR VEHICLE 323 • If frequent coolant additions are required, or if the ONLY the correct type thermostat. Other designs may level in the coolant recovery bottle does not drop when result in unsatisfactory coolant performance, poor gas the engine cools, the cooling system should be pres- mileage, and increased emissions.
Page 324: Brake System
324 MAINTAINING YOUR VEHICLE Inspect all hose connections such as clamps and cou- WARNING! plings to make sure they are secure and no leaks are present. Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting Components should be replaced immediately if there is or riding on the brake pedal can result in abnormally any evidence of wear or damage that could cause failure.
Page 325: Brake Fluid Level Check
MAINTAINING YOUR VEHICLE 325 Insure nylon tubing in these areas has not melted or should be replaced immediately! Eventual deterioration collapsed. of the hose can take place resulting in a possibility of a burst failure. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are WARNING! present.
Page 326 326 MAINTAINING YOUR VEHICLE Overfilling of fluid is not recommended because it may WARNING! cause leaking in the system. • Overfilling the brake fluid reservoir can result in Add enough fluid to bring the level up to the require- spilling brake fluid on hot engine parts and the ments described on the brake fluid reservoir.
Page 327: Fuel System Hoses
MAINTAINING YOUR VEHICLE 327 Care should be taken in installing quick connect fittings CAUTION! to insure they are properly installed and fully connected. See your authorized dealer for service. Do not allow petroleum base fluid to contaminate the brake fluid, all brake seal components could be Automatic Transmission damaged causing partial or complete brake failure.
Page 328 328 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! Using a transmission fluid other than the manufac- The fluid level is preset at the factory and does not turer’s recommended fluid may cause deterioration require adjustment under normal operating condi- in transmission shift quality and/or torque converter tions.
Page 329: Front And Rear Wheel Bearings
MAINTAINING YOUR VEHICLE 329 • Police, taxi, limousine, commercial type operation, or The following maintenance recommendations will enable trailer towing where the vehicle is driven regularly for you to obtain maximum benefit from the corrosion more than 45 minutes of continuous operation. resistance built into your vehicle.
Page 330 330 MAINTAINING YOUR VEHICLE Washing CAUTION! • Wash your vehicle regularly. Always wash your ve- Do not use abrasive or strong cleaning materials hicle in the shade using Mopar Car Wash or a mild such as steel wool or scouring powder, which will car wash soap, and rinse the panels completely with scratch metal and painted surfaces.
Page 331 MAINTAINING YOUR VEHICLE 331 • If your vehicle is damaged due to an accident or heavy soil, use Mopar Wheel Cleaner or select a non- similar cause which destroys the paint and protective abrasive, non-acidic cleaner. Do not use scouring pads, coating have your vehicle repaired as soon as possible.
Page 332 332 MAINTAINING YOUR VEHICLE Your leather upholstery can be best preserved by regular Glass Surfaces cleaning with a damp soft cloth. Small particles of dirt All glass surfaces should be cleaned on a regular basis can act as an abrasive and damage the leather upholstery with Mopar Glass Cleaner or any commercial and should be removed promptly with a damp cloth.
Page 333: Fuse Panel
MAINTAINING YOUR VEHICLE 333 2. Dry with a soft tissue. FUSE PANEL Seat Belt Maintenance Interior Fuses Do not bleach, dye or clean the belts with chemical The fuse panel is on the lower instrument panel just to solvents or abrasive cleaners. This will weaken the fabric. the left of the steering column.
Page 334 334 MAINTAINING YOUR VEHICLE Cav- Cartridge Cav- Cartridge Mini Fuse Description Mini Fuse Description Fuse Fuse 30 Amp Audio Amp (B+) 10 Amp Final Drive Control Green Module (FDCM), Heater Ventilation, Air 15 Amp Sunroof (B+) Conditioning (HVAC), Blue Switch Bank, Transfer 10 Amp Htd Mirror (EBL) Case Switch, O/H,...
Page 335 MAINTAINING YOUR VEHICLE 335 Cav- Cartridge Cav- Cartridge Mini Fuse Description Mini Fuse Description Fuse Fuse 20 Amp Cigar Ltr (R/A) Spare Yellow (Acc De- lay) 10 Amp Tire Pressure Trans- ducers (R/O) 15 Amp Rear Wiper (B+) Blue 10 Amp Steering Control Mod- ule (SCM), Diag.
Page 336: Underhood Fuses (Power Distribution Center)
336 MAINTAINING YOUR VEHICLE Underhood Fuses (Power Distribution Center) Cav- Cartridge Mini Fuse Description Fuse 30 Amp Power Outlets Pink 30 Amp Rr Wiper/Ign R/O Pink 30 Amp ABS Pump Pink Spare 50 Amp Auto Shut Down (ASD) Spare 40 Amp Acc Delay/Seats Power Distribution Center Green...
Page 337 MAINTAINING YOUR VEHICLE 337 Cav- Cartridge Cav- Cartridge Mini Fuse Description Mini Fuse Description Fuse Fuse 30 Amp Cig Ltr/T-Tow 20 Amp PCM Batt (Gasoline Pink Yellow Only) 40 Amp Rear Window Defog- 30 Amp ABS Valves Green ger (EBL)/Htd Mirror Green 40 Amp Junction Block (JB)
Page 338: Underhood Fuses (Integrated Power Module)
338 MAINTAINING YOUR VEHICLE Underhood Fuses (Integrated Power Module) Cav- Cartridge Mini Fuse Description Fuse 10 Amp Trailer-Tow Park Lamps 10 Amp Rt Park Lamps 20 Amp Front Control Module Yellow (FCM) Batt #4 20 Amp Front Control Module Yellow (FCM) Batt #2 20 Amp Adjustable Pedal...
Page 339: Vehicle Storage
MAINTAINING YOUR VEHICLE 339 Cav- Cartridge Cav- Cartridge Mini Fuse Description Mini Fuse Description Fuse Fuse 20 Amp Front Control Module 10 Amp Occupant Restraint Yellow (FCM) Batt #1 Controller (ORC) R/S 20 Amp Lt Trailer-Tow Stop/ 10 Amp Occupant Restraint Yellow Turn Controller (ORC) R/O...
Page 340: Replacement Bulbs
340 MAINTAINING YOUR VEHICLE insure adequate system lubrication to minimize the Exterior Lights Bulb Type possibility of compressor damage when the system is Backup Lights ......3157K started again.
Page 341: Bulb Replacement
MAINTAINING YOUR VEHICLE 341 BULB REPLACEMENT 3. Turn the low or high beam bulb 1/4 turn counter clockwise to remove from housing. Head Light 1. Open the hood. 2. Remove the headlamp cover. 4. Disconnect the electrical connector and replace the bulb.
Page 342: Front Turn Signal
342 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Front Turn Signal 1.
Page 343: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE 343 3. Turn the turn signal bulb 1/4 turn counter clockwise CAUTION! to remove from housing. Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol.
Page 344: Lights
344 MAINTAINING YOUR VEHICLE CAUTION! Do not touch the new bulb with your fingers. Oil contamination will severely shorten bulb life. If the bulb comes in contact with any oily surface, clean the bulb with rubbing alcohol. Rear Tail, Stop, Turn Signal, and Back-Up Lights 1.
Page 345: Center High Mounted Stop Light (Chmsl)
MAINTAINING YOUR VEHICLE 345 3. Squeeze the socket assembly tabs to remove it from the Center High Mounted Stop Light (CHMSL) housing. 1. Remove the two screws securing the CHMSL. 2. Twist the bulb socket to remove from the CHMSL 4.
Page 346: Fluid Capacities
346 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 21 Gallons 79 Liters Engine Oil with Filter 6.1 Liter Engine (SAE 0W-40, API Certified) 7 Qts 6.6 Liters Cooling System * 6.1 Liter Engine (Mopar Engine Coolant/Antifreeze 5 Year/ 14.8 Qts 14 Liters 100,000 Mile Formula)
Page 347: Fluids, Lubricants, And Genuine Parts
MAINTAINING YOUR VEHICLE 347 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) Engine Oil (6.1L Engine) Use API Certified SM/CF synthetic engine oil. SAE 0W-40 is recommended, meeting the requirements of DaimlerChrysler Material Standard MS-10725.
Page 348: Chassis
348 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission Mopar ATF+4 Automatic Transmission Fluid Transfer Case Mopar NV146 Transfer Case Fluid or equivalent. Usage of other fluid/ lubricants is NOT recommended. Axle Differential (Front-Rear) Mopar Synthetic Gear & Axle Lubricant SAE 75W-140 (API-GL5) or equivalent.
Page 349 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..350 Schedule “B” ......353 Maintenance Schedules .
Page 350: Emission Control System Maintenance
350 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The “Scheduled” maintenance services, listed in bold There are two maintenance schedules that show the type must be done at the times or mileages specified to required service for your vehicle. assure the continued proper functioning of the emission First is Schedule B .
Page 351 MAINTENANCE SCHEDULES 351 NOTE: Most vehicles are operated under the conditions CAUTION! listed for Schedule “B.” Failure to perform the required maintenance items NOTE: If ANY of these apply to you, change your may result in damage to the vehicle. engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first, and follow the maintenance rec- ommendations in “Maintenance Schedule B.”...
Page 352 352 MAINTENANCE SCHEDULES Once a Month At Each Oil Change • Check the tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the exhaust system. • Inspect the battery and clean and tighten the terminals •...
Page 353: Schedule "B" 353
SCHEDULE “B” 353 Schedule “B” NOTE: If ANY of these apply to you, change your Follow this schedule if you usually operate your vehicle engine oil every 3,000 miles (5 000 km) or 3 months, under one or more of the following conditions. whichever comes first, and follow the maintenance rec- ommendations in “Maintenance Schedule B.”...
Page 354 354 SCHEDULE “B” Miles 3,000 6,000 9,000 12,000 15,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary.
Page 355 SCHEDULE “B” 355 Miles 18,000 21,000 24,000 27,000 30,000 (Kilometers) (30 000) (35 000) (40 000) (45 000) (50 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary.
Page 356 356 SCHEDULE “B” Miles 33,000 36,000 39,000 42,000 45,000 (Kilometers) (55 000) (60 000) (65 000) (70 000) (75 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary.
Page 357 SCHEDULE “B” 357 Miles 48,000 51,000 54,000 57,000 60,000 (Kilometers) (80 000) (85 000) (90 000) (95 000) (100 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary.
Page 358 358 SCHEDULE “B” Miles 63,000 66,000 69,000 72,000 75,000 (Kilometers) (105 000) (110 000) (115 000) (120 000) (125 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary.
Page 359 SCHEDULE “B” 359 Miles 78,000 81,000 84,000 87,000 90,000 (Kilometers) (130 000) (135 000) (140 000) (145 000) (150 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary.
Page 360 360 SCHEDULE “B” Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary.
Page 361 SCHEDULE “B” 361 Miles 108,000 111,000 114,000 117,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change the engine oil and engine oil filter, if not replaced at 3 months. Inspect the engine air cleaner filter, replace if nec- essary.
Page 362 362 SCHEDULE “B” Inspection and service should also be performed anytime * This maintenance is not required if the belt was a malfunction is observed or suspected. Retain all re- previously replaced. ceipts. This maintenance is recommended by the manufac- turer to the owner, but is not required to maintain emissions warranty.
Page 363: Schedule "A" 363
SCHEDULE “A” 363 Schedule “A” Miles 6,000 12,000 18,000 24,000 30,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) [Months] [12] [18] [24] [30] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if necessary.
Page 364 364 SCHEDULE “A” Miles 36,000 42,000 48,000 54, 000 (Kilometers) (60 000) (70 000) (80 000) (90 000) [Months] [36] [42] [48] [54] Change the engine oil and engine oil filter. Inspect the brake linings.
Page 365 SCHEDULE “A” 365 Miles 60,000 66,000 72,000 78,000 (Kilometers) (100 000) (110 000) (120 000) (130 000) [Months] [60] [66] [72] [78] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if nec- essary.
Page 366 366 SCHEDULE “A” Miles 84,000 90,000 96,000 102, 000 (Kilometers) (140 000) (150 000) (160 000) (170 000) [Months] [84] [90] [96] [102] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if nec- essary.
Page 367 SCHEDULE “A” 367 Miles 108,000 114,000 120,000 (Kilometers) (180 000) (190 000) (200 000) [Months] [108] [114] [120] Change the engine oil and engine oil filter. Inspect the engine air cleaner filter, and replace if necessary. Inspect the PCV Valve, replace if necessary. Inspect the drive belt, replace if necessary.* Inspect the brake linings.
Page 368 368 SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 369: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Reporting Safety Defects ....373 Vehicle ......370 In Canada .
Page 370: Suggestions For Obtaining Service For Your Vehicle
Warranty service must be done by an authorized or work done that is not on your maintenance log, let the Chrysler, Dodge, or Jeep dealer. We strongly recommend service advisor know. that you take your vehicle to your selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 371 IF YOU NEED CONSUMER ASSISTANCE 371 • Vehicle identification number technicians, special tools, and the latest information to assure your vehicle is fixed correctly and in a timely • Vehicle delivery date and mileage manner. DaimlerChrysler Motors Corporation Customer Center This is why you should always talk to your dealer’s P.O.
Page 372 372 IF YOU NEED CONSUMER ASSISTANCE Customer Assistance For The Hearing Or Speech contract, call the manufacturer’s Service Contract Na- Impaired (TDD/TTY) tional Customer Hotline at 1-800-521-9922. To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
Page 373: Warranty Information (U.s. Vehicles Only)
IF YOU NEED CONSUMER ASSISTANCE 373 WARRANTY INFORMATION (U.S. Vehicles Only) campaign. However, NHTSA cannot become involved in See the Warranty Information Booklet for the terms and individual problems between you, your dealer, and the provisions of DaimlerChrysler’s warranties applicable to manufacturer.
Page 374: Publication Order Forms
374 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals. PUBLICATION ORDER FORMS To order the following manuals, you may use either the Filled with diagrams, charts and detailed illustrations, website or the phone numbers listed below. Visa, Mas- these practical manuals make it easy for students and tercard, American Express, and Discover orders are ac- technicians to find and fix problems on computer- cepted.
Page 375: Department Of Transportation Uniform Tire Quality Grades
IF YOU NEED CONSUMER ASSISTANCE 375 Call Toll Free at: All Passenger Car Tires Must Conform to Federal Safety Requirements in Addition to These Grades. • 1–800–890–4038 (U.S.) Treadwear • 1–800–387–1143 (Canada) The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled con- ditions on a specified government test course.
Page 376: Temperature Grades
376 IF YOU NEED CONSUMER ASSISTANCE on specified government test surfaces of asphalt and grade C corresponds to a level of performance which all concrete. A tire marked C may have poor traction perfor- passenger car tires must meet under the Federal Motor mance.
Page 377 INDEX...
Page 378 378 INDEX ABS (Anti-Lock Brake System) ... . 173,245 Antifreeze (Engine Coolant) ....319,346 Adding Engine Coolant (Antifreeze) ..320 Disposal .
Page 379 INDEX 379 Battery ....... 312 Bulb Replacement ..... 340,341 Emergency Starting .
Page 380 380 INDEX Cellular Phone ......78 Coolant Capacity ..... . 346 Center High Mounted Stop Light .
Page 381 INDEX 381 Diagnostic System, Onboard ....301 Emergency, In Case of Dimmer Switch, Headlight ....119 Freeing Vehicle When Stuck .
Page 382 382 INDEX Oil Change Interval ....306 Finish Care ......330 Oil Selection .
Page 383 INDEX 383 Fuel ....... . . 270 Gauges Additives ......272 Coolant Temperature .
Page 384 384 INDEX Heated Mirrors ......77 Instrument Panel Lens Cleaning ... . . 332 Heated Seats .
Page 385 INDEX 385 LATCH Center Mounted Stop ....345 (Lower Anchors and Tether for CHildren) ..58,60 Cruise ......177 Lead Free Gasoline .
Page 386 386 INDEX Low Tire ......175 Load Floor, Cargo ..... . . 163 Malfunction Indicator (Check Engine) .
Page 387 INDEX 387 Malfunction Indicator Light (Check Engine) . . 172,302 Navigation Radio ......209 Manual, Service ......374 Navigation System .
Page 388 388 INDEX Opener, Garage Door (HomeLink ) ... 145 Power Outside Rearview Mirrors ....75 Distribution Center (Fuses) .
Page 389 INDEX 389 Radio, Navigation ..... . . 209 Remote Starting System ....24 Radio Operation .
Page 390 390 INDEX Seat Belts ......35 Power ......102,103 Adjustable Upper Shoulder Anchorage .
Page 391 INDEX 391 Spark Plugs ......309 Sunglasses Storage ..... . . 145 Speed Control (Cruise Control) .
Page 392 392 INDEX General Information ....258 Recreational ......289 High Speed .
Page 393 INDEX 393 Transmitter, Remote Keyless Entry (RKE) ..19 Viscosity, Engine Oil ..... . 308 Tread Wear Indicators .
Page 394 394 INDEX Fluid ....... 316 Wiper Blade Replacement ....316 Windshield Wiper Blades .
Page 395 NOTES...
Page 396 NOTES...
Page 397 NOTES...
Page 398 NOTES...
Page 399 NOTES...
Page 400 NOTES...

This manual is also suitable for:

Grand cherokee srt8