Download Print this page
PEERLESS PLA 60 Installation And Assembly Manual

PEERLESS PLA 60 Installation And Assembly Manual

Articulating swivel arm for 37" - 60" plasma screens

Advertisement

Quick Links

Installation and Assembly
37" - 60" Plasma Screens
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 729-0307 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
- Articulating Swivel Arm for
Models: PLA 60, PLA 60-S,
This product is UL Listed. It must be
installed by a qualified professional
R
installer.
Maximum UL Load Capacity: 175 lb (79 kg)
ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06
PLAV 60, PLAV 60-S

Advertisement

loading
Need help?

Need help?

Do you have a question about the PLA 60 and is the answer not in the manual?

Questions and answers

Summary of Contents for PEERLESS PLA 60

  • Page 1 Installation and Assembly - Articulating Swivel Arm for Models: PLA 60, PLA 60-S, PLAV 60, PLAV 60-S 37" - 60" Plasma Screens This product is UL Listed. It must be installed by a qualified professional installer. Maximum UL Load Capacity: 175 lb (79 kg) 3215 W.
  • Page 2: Tools Needed For Assembly

    Read instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-729-0307.
  • Page 3: Parts List

    Before you start make sure all parts Parts List listed are included with your product. PLA 60 PLA 60-S PLAV 60 PLAV 60-S DESCRIPTION QTY. PART # PART # PART # PART # A wall plate 201-1040 201-4040 201-1040 201-4040 B tilt-roll assembly 201-1093 201-4093...
  • Page 4: Installation To Wood Stud Wall

    Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
  • Page 5 Installation to Concrete Wall WARNING • Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor. • Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • Page 6 WARNING • If you are uncertain that product is properly installed, call customer care. Note: There are five mounting positions. The center position is shown (right). Slide washer (J) over wall support arm axle (D). Next, insert plastic cap (N) into axle. Then, insert holding pin (M) into axle.
  • Page 7 Attach two pieces of vinyl trim (E) to wall plate (A). Next, attach one piece of vinyl trim to bottom of swivel box on arm assembly (C). Insert one finishing cap (L) into each unused hole of wall plate (A). SWIVEL BOX Note: Refer to adapter bracket instruction sheet for attachment of adapter bracket to plasma before proceeding with step 5.
  • Page 8 WARNING • Use an assistant or mechanical lifting equipment to safely lift and position the plasma TV. Insert two M10 screws (F) into swivel box on arm assembly (C) as shown. Leave approx. 1/4" of exposed thread. SWIVEL BOX .25" Hook tilt-roll assembly (B) onto M10 screws (F).
  • Page 9 9 of 9 ISSUED: 05-02-06 SHEET #: 202-9112-3 12-05-06 ©2006 Peerless Industries, Inc. All rights reserved. Peerless is a registered trademark of Peerless Industries, Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.

This manual is also suitable for:

Pla 60-sPlav 60Plav 60-sPla 60-s