Advertisement
•
Loosen knob (Figure 7, Key No. 14). Place V-belt on
motor and drive pulleys (Figure 8, Key Nos. 46 and
50).
•
Tension V-belt by pushing down on motor mount
plate and tightening knob. Belt is properly tensioned
when light pressure applied to midpoint of the belt
produces about 1/2" deflection.
•
Make sure blade teeth are pointing down towards
table. Turn blade inside out if necessary.
•
Rotate handwheel (Figure 8, Key No. 23) counter-
clockwise to move blade wheels towards each other.
•
Loosen handle (Figure 9, Key No. 30). Rotate knob
(Figure 9, Key No. 22) to lower upper blade guide
assembly as low as possible.
•
Loosen three screws (Figure 9, Key No. 5). Remove
blade guards (Figure 9, Key Nos. 4 and 38).
•
Slip blade over upper and lower blade wheels, and
center blade on blade wheels. Slide blade in
between blade guides.
•
Replace blade guards and secure
in place by tight-
ening screws. Raise upper blade guide assembly.
Rotate handwheel clockwise to tension blade.
Position clutch handle (Figure 8, Key No. 62) to
"Wood". See Figure 2.
Wood
Metal
Figure 2 - Clutch Handle Position
NOTE: The blade must be tensioned and tracked, and
the blade guides must be adjusted before operation of
the saw. Refer to "Tensioning Blade", "Tracking Blade"
and "Blade Guides" in the OPERATION section, page 6.
ATTACH TABLE
Refer to Figure 10.
•
Table (Key No. 1) is attached to frame with two cast
iron trunnions.
•
Remove table stud (Key No. 16)
•
Finger tighten one socket head bolt with washer (Key
Nos. 3 and 4) on left side of front trunnion (Key No.
2) into table.
•
Bring table to frame by inserting back of blade into
slot. Position table with back trunnion (Key No. 5) on
guide posts which are welded to frame.
•
Position front trunnion so it rides on guide post.
Attach handle with flat washer (Key Nos. 13 and 11)
to secure back trunnion.
•
Insert trunnion rod with acorn nut and fiat washer
(Key Nos. 10 and 11) through other guide post and
attach the internally threaded knob with flat washer
(Key Nos. 12 and 11) to the trunnion rod.
•
Mount second bolt with washer on front trunnion.
Position front trunnion fiat against bottom of table
and tighten internally threaded knob to secure.
•
Tighten socket head bolts (Key No. 3) to secure trun-
nions to table. Install table stud.
SET HORIZONTAL
STOP
Refer to Figure 10.
•
When table is attached to frame, a bolt (Key No. 14)
is used for a horizontal stop.
•
Loosen trunnion knob and set table at 90 ° to blade
using a square.
•
Secure position of table with knob.
• Adjust bolt to contact bottom edge of table.
•
Lock bolt in position with hex nut (Key No. 15).
ATTACH RIP FENCE
Refer to Figure 10.
•
Rip fence (Key No. 19) rides in the slot of table (Key
No. 1).
•
Slide rip fence into slot.
•
Hold rip fence to table and fasten by threading knob
(Key No. 20) into rip fence.
•
Rip fence can be repositioned by loosening knob.
ALIGN TABLE
Refer to Figure 10.
•
The table must be aligned properly so that the blade
is at a right angle to the table and that the rip fence
is aligned with the blade.
•
Lock the table in the horizontal position. Mount the
rip fence on the table. Slide the rip fence next to, but
not touching, the blade. Lock the rip fence.
•
Check that the blade is aligned parallel with the rip
fence. If the blade and fence are not parallel, loosen
handle and knob (Key Nos. 12 and 13) on the trun-
nions (Key Nos. 2 and 5). Adjust the table position so
that the blade and rip fence are parallel. Secure the
table position by tightening handle and knob.
• After assembly, the table has to be aligned in order
to have the blade running through the center of the
slot in the table insert.
•
To move table sideways, loosen bolts (Key No. 3) on
the trunnions (Key Nos. 2 and 5). Move table to left
or right until blade runs through the center of slot.
Tighten bolts and make sure that table stays in posi-
tion while bolts are being tightened.
4
Advertisement
